Detroit Radiant Products P-16T Installation, Operation, Maintenance And Parts

Pt series

Advertisement

Quick Links

Detroit Radiant Products Co.
PT Series
Models P-16T & P-32T
Installation,
Operation,
Maintenance,
and Parts
Important! The LP gas heater is designed and
approved for use as a construction heater in
accordance with the ANSI Z83.7a-2007 Standard.
Other standards govern the use of fuel gases and
heat producing products in specific applications.
Check with local authorities if you have questions or
need advice about applications.
Failure to comply with the precautions and instructions provided with this heater can
result in death, serious bodily injury, and property loss or damage from hazards of fire,
explosion, burns, asphyxiation, carbon monoxide poisoning, and/or electrical shock.
Only persons who can understand and follow the instructions should use or service
this heater. If you need assistance or heater information such as an instruction manual,
label, etc. contact the manufacturer.
Fire, burn, inhalation, and explosion hazard. Keep combustibles such as building
materials, paper, or cardboard a safe distance away from the heater as recommended
by the instructions. Never use the heater in spaces which do or may contain volatile or
airborne combustibles or products such as gasoline, solvents, paint thinner, dust
particles, or unknown chemicals.
This heater is not approved for use in any indoor residential application. This
includes, but is not limited to, attached garages, solarium, living quarters, mobile
homes, campers, tents, recreational vehicles, etc.
For Your Safety
Propane gas is VERY FLAMMABLE! It is scented and its strong odor is readily detectable. In the event of a leak,
propane will accumulate and the possibility of a fire is present. If you smell gas:
• Never strike a match, create a flame, or create an electric spark.
• Move the heater outside and ventilate the area thoroughly.
• Find and correct the source of the leak before attempting to light the heater. If the leak cannot be corrected, do
not tamper with the heater.
• Turn the heater "OFF" and consult the manufacturer, a qualified installer, or the gas supplier.
INSTALLER: Present this manual to the end user.
Keep these instructions in a clean and dry place for future reference.
Model#: ___________________ Serial #: _________________________
Manual
!
WARNING
!
(located on rating label)
LIOPT-Rev. 29110
Print: LIOPT-1M-11/16_r1-01/17 (WHI)
Replaces: LIOPT-3M-01/14 (CDS)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P-16T and is the answer not in the manual?

Questions and answers

Summary of Contents for Detroit Radiant Products P-16T

  • Page 1 Detroit Radiant Products Co. PT Series Manual Models P-16T & P-32T Installation, Operation, Maintenance, and Parts Important! The LP gas heater is designed and approved for use as a construction heater in accordance with the ANSI Z83.7a-2007 Standard. Other standards govern the use of fuel gases and heat producing products in specific applications.
  • Page 2: Table Of Contents

    Series Contents 1.0 Safety..............3 Warning Symbols.
  • Page 3: Safety

    Safety • Warning Symbols • Applications Series Safety WARNING Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. All persons involved with the operation and maintenance of this heater must read and understand the information in this manual before use or service of the heater.
  • Page 4: Clearance To Combustibles

    Series Safety • Clearance to Combustibles Clearance to Combustibles WARNING Improperly connected gas line may result in serious injury or death, explosion, poisonous fumes, toxic gases, or asphyxiation. Connect gas lines in accordance to national, state, provincial, and local codes. Placement of explosive objects, flammable objects, liquids, and vapors close to the heater may result in explosion, fire, property damage, serious injury, or death.
  • Page 5: Safety Signs And Labels

    Safety Signs and Labels Safety warning labels must be maintained on the infrared heater. Illustrations of the safety labels, and their locations, are pictured below. DETROIT RADIANT PRODUCTS - RADIANT HEATER DETROIT RADIANT PRODUCTS - RADIANT HEATER PORTABLE INFRARED CONSTRUCTION HEATER...
  • Page 6: Installation

    Series Installation • Assembly Installation Read and understand the installation, operating, and maintenance instructions thoroughly before assembling or operating this equipment. WARNING Insufficient ventilation may result in fire, explosion, health problems, carbon monoxide poisoning, serious injury, or death. Vent enclosed spaces and buildings according to national, state, provincial, and local codes.
  • Page 7: Heater Dimensions

    Products Co. voids all approvals and warranties. Figure 2.1 • Heater Dimensions Chart 2.1 • Heater Dimensions (in Inches) Model No. Dim “X” Dim “Y” P-16T 10 1/16 13 1/8 P-32T 10 1/16 18 5/8 • Chart 2.2 Operating Values...
  • Page 8: Mounting The Heater

    Connect gas lines in accordance to national, state, and local codes. Mounting the Heater (P-16T, P-32T) Attach the mounting bracket to the heater by lining up the upper hole of the bracket with the mounting hole located on the side of the heater. Fasten the two parts with the 3/8-16 thumbscrew provided.
  • Page 9: Operation

    Operation • Lighting the Heater • Shutdown Series Operation WARNING Improperly connected or damaged gas line may result in fire, explosion, poisonous fumes, toxic gases, asphyxiation, serious injury, or death. Check the hose assembly and gas connection before each use. Gas lines must be installed in accordance to national, state, provincial, and local codes.
  • Page 10: Maintenance

    Series Maintenance • Storage • Troubleshooting Guide Maintenance WARNING Gas hoses that are cut or have abrasions and/or wear may fail and release gas resulting in fire, explosion, serious injury, or death. Replace worn or damaged hoses before use. Never operate the heater if repairs are necessary. If the heater has not been in service for an extended period of time, the following maintenance procedures should be performed before heater operation: Inspect unit before each use and at least annually by a qualified service person.
  • Page 11: Parts

    Type-1 inlet P-109P Propane orifice spud for P-16T P-125 LP gas valve, assembled w/ all fittings for P-32T P-110P Propane orifice spud for P-32T P-126 LP gas valve, assembled w/ all fittings for P-16T Visit http://store.reverberray.com for additional replacement parts information.
  • Page 12: Repair

    Corrective Action: Replace the rayhead assembly or return it to Detroit Radiant Products for repair. Repair cost is $48.00 for each P-16T model and $55.00 for each P-32T model. Repair charges include return shipping and handling costs. Units can be returned COD via UPS (additional fees for COD service will apply).

This manual is also suitable for:

P-32t

Table of Contents