Advertisement

Quick Links

Glen Dimplex Professional Appliances:
This appliance must be installed by a competent person in compliance with the installa-
tion and servicing instructions and national regulations in force at the time.
Particular attention must be paid to the following:
Adjustment must not be made by the user to parts which are protected by the manu-
facturer.
Users of this appliance should be conversant with the appropriate provisions of the
Fire Precautions Act and the requirements of the Gas Safety Regulations, in
particular, the need to service the appliance on a regular basis to ensure the continued
safe and efficient performance of the appliance.
Always ensure that a competent person undertakes any servicing.
After installation, the installer must ensure that the user is instructed on the safe use
of this appliance, and has a copy of the user guide left with them for reference.
This equipment is only for professional use, and should only be operated by qualified
persons.
It is the responsibility of the supervisor or equivalent to ensure that users wear suit-
able protective clothing and draw attention to the fact that, some parts will, by
necessity become very hot and will cause burns if touched accidently.
D
Always take care when removing food from the grill as the area around the cavity
may be hot.
D
Always use oven gloves when handling any utensils which have been in the grill as
they will be hot.
D
Always make sure that the grill shelf is secured correctly.
8
Plastic cooking utensils can melt if they come into contact with the grill. Never
leave them close to, or on top of the grill.
8
Do not wrap foil around the grill shelf.
8
Do not drape tea towels near the grill while it is on, this will cause a fire hazard.
8
Do not use this appliance to heat anything other than food items, and do not use
for heating the room.
Salamander Grill
Gas Safety (Installation & Use) Regulations.
Health and Safety at Work Act.
This appliance must be earthed
When using the appliance:
(GB/IE)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Salamander and is the answer not in the manual?

Questions and answers

Summary of Contents for Glen Dimplex Salamander

  • Page 1 Glen Dimplex Professional Appliances: Salamander Grill (GB/IE) This appliance must be installed by a competent person in compliance with the installa- tion and servicing instructions and national regulations in force at the time. Particular attention must be paid to the following: Gas Safety (Installation &...
  • Page 2 These appliances must be installed and serviced by a competent person as stipulated by the Gas Safety (Installation & Use) Regulations IMPORTANT The installer must ensure that the installation of the appliance is in conformity with these instructions and National Regulations in force at the time of installation. Particu- lar attention MUST be paid to - •...
  • Page 3: Section 1 - Installation

    SECTION 1 - INSTALLATION UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER ARE NOT TO BE ADJUSTED BY THE INSTALLER 1.1 NETT WEIGHT and DIMENSIONS WIDTH DEPTH HEIGHT WEIGHT (mm) (mm) (mm) (kg) CONN. 3/4” BSP (female) The grill may be mounted on any of the following options: Feet (supplied), floor stand or wall bracket.
  • Page 4 Installation pipe work should be fitted in accordance with IGE/ UP/ 2. The pipe work should be of adequate size but not smaller than the gas inlet connection on the ap- pliance, i.e. Rp 3/4” B.S.P. An isolating cock must be located close to the appliance to allow shut-down during an emergency or servicing of the gas supply.
  • Page 5: Section 2 - Assembly And Commissioning

    SECTION 2 - ASSEMBLY AND COMMISSIONING 2.1 ASSEMBLY 2.1.1 Grill Unit Unpack grill and check that all components are undamaged. Parts supplied loose are specified in the contents list below: Brander Plate Brander Drip Tray Grill Shelf Grill Shelf Handle / Shields (x2) Drip Tray Adjustable Feet (x4) 2.1.2 Appliance Mounting Accessories...
  • Page 6: Instruction To User

    2.5.2 Checking the performance of the controls Light grill burner as detailed in Section 2.5.3. Check ignition is smooth and without delay. Repeat operation several times. 2.5.3 Lighting sequence Important: Prior to operation, ensure ALL packing material has been removed from the appliance.
  • Page 7: Section 3 - Servicing

    SECTION 3 - SERVICING IMPORTANT: BEFORE ATTEMPTING ANY SERVICING, ENSURE ISOLATING COCK IS TURNED OFF AND CANNOT BE INADVERTENTLY TURNED ON. AFTER ANY MAINTE- NANCE TASK, CHECK APPLIANCE TO ENSURE THAT IT PERFORMS CORRECTLY AND CARRY OUT ANY NECESSARY ADJUSTMENTS AS DETAILED IN SECTION 1. After carrying out any service or exchange of gas carrying components - ALWAYS CHECK FOR GAS TIGHTNESS 3.1 REMOVAL OF PLAQUES AND BURNERS...
  • Page 8: Fault Check List

    3.3.2 Thermocouple Remove top front panel and top panel as detailed in section 3.1.1 Remove RH side panel as detailed in section 3.1.2 Remove nut securing thermocouple sensor to support bracket and pull thermo- couple through support bracket from the rear Undo thermocouple connection at FFD section of gas tap and carefully remove thermocouple.
  • Page 9: Section 4 Spares

    If a flame is established but not maintained then follow this check list: Check the thermocouple sensor is secured correctly and that the burner ports are clean Check that the thermocouple is not damaged and is securely fixed to FFD section of the gas control Check that the FFD is energising and maintaining the flame If after carrying out the above, the burner is still not maintaining the flame check...
  • Page 10: Section 1 About Your Appliance

    USER’S GUIDE SECTION 1 ABOUT YOUR APPLIANCE This appliance must be installed and serviced by a competent person as stipulated by the Gas Safety (Installation & Use) Regulations This equipment is only for professional use, and should only be operated by qualified persons.
  • Page 11: Section 5 Cleaning And Maintenance

    2.2 Hot Ignition Press and turn knob to full flame position Ignite burner using piezo ignition button and continue to hold knob in for a further 5-10 seconds before release Burner should remain lit but if burner goes out return to Step 1 and repeat ignition procedure When burner remains lit, turn knob to required position To turn the burner off, turn knob to the OFF position...
  • Page 12 Vitreous enamel surfaces Approved cleaning agents which have the mark of the Vitreous Enamel Development Centre are recommended. It is advisable to clean daily after use. Wipe clean the vitreous enamel surfaces while they are still warm using a soft cloth and hot soapy water.
  • Page 13: Spares List

    SPARES LIST Part Number Description 083076900 Plaque (single) 082980700 Thermocouple 080125000 Locknut thermocouple BRASS 503095700 Bracket thermocouple 082544300 Grill electrode 503095800 Bracket electrode 082541700 No 4 x 3/8” torx pan head bz 083064902 Tap grill 082983800 Control knob 081502200 Generator ignition piezo black 083076700 Handle shield 083076600...
  • Page 16 Glen Dimplex Professional Appliances Stoney Lane, Prescot, Merseyside, L35 2XW Tel: 0844 815 3755 08 31177 00 © 10.2010...

Table of Contents