Summary of Contents for Fiore FI310
- Page 1 ™ COOK TOP INSTALLATION OPERATING INSTRUCTIONS FI310/FI320/ FI640/FI850/FI950...
-
Page 2: Safety Information
If damage or defect is discovered DO NOT IN- STALL your Fiore product. Any claimed damage or defect to the finish of the product after the product has been installed will be excluded from any manufacturer warranty. -
Page 3: For Your Safety
FOR YOUR SAFETY: If the information in this manual is not followed exactly, a fire, explosion or gas leak may result. It may cause prop- erty damage, personal injury or death. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance. WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. - Page 4 ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage, frequency and connected to an individual properly grounded branch circuit. The appliance must also be protected by a circuit breaker or fuse having amperage as not- ed on the rating plate. We recommend you to have the electrical wiring and hookup of your cooktop connected by a qualified electrician After installation, have the electrician show you where your main cooktop disconnect is located.
-
Page 5: Table Of Contents
COOK TOP INSTALLATION AND OPERATING INSTRUCTIONS TABLE OF CONTENTS INSTALLATION PREPARATION DIMENSIONS AND CLEARANCES POWER SUPPLY LOCATIONS INSTALLATION INSTRUCTIONS INSTALL PRESSURE REGULATOR ASSEMBLE BURNERS AND CHECK IGNITION LP GAS CONVERSION SETTING THE MINIMUM FLAME... -
Page 6: Installation Preparation
INSTALATION PREPARATION MODELS AVAILABLE FI310 Series 11.8” Natural Gas/11.8” LP FI320 Series 11.8” Natural Gas/11.8” LP FI640 Series 22.8” Natural Gas/22.8” LP FI850 Series 22.8” Natural Gas/22.8” LP FI950 Series 30.3” Natural Gas/30.3” LP These models are factory set for either natural gas or LP gas operation. Be sure to order the correct model for the installation situation. - Page 7 INSTALATION PREPARATION ADVANCE PLANNING Refer to “Installation Preparation” for information on appropriate placement and necessary clearances when planning installation. Avoid placing cabinetry directly above cooktop when possible. If cabinetry is used above cooking surface: Use cabinets no more than 13″ deep. Maintain 30″...
- Page 8 PRE-INSTALATION CHECKLIST When preparing cooktop opening, make sure the inside of the cabinet and the cooktop do not interfere with each other. (See section on preparing the opening.) Slide the cooktop out of the end of the box. Remove packaging materials, grate boxes, regulator and literature package from the cooktop before beginning installation.
- Page 9 GAS SUPPLY AND PRESSURE REGULATOR Gas supply: These cooktops are shipped from the factory set for either natural gas or LP gas. Check to be sure you have the correct cooktop for the type of gas being used. The pressure regulator must be connected in series with the manifold of the cooktop and must remain in series with the supply line regardless type of gas being used.
- Page 10 INSTALL PRESSURE REGULATOR WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leakage and per- sonal injury. Always use new flexible connectors when installing a gas appliance. To reduce the possibility of gas leakage, apply Teflon tape or a thread compound approved for use with LP or Natural gases to all threaded connections.
-
Page 11: Electrical Connection
Install a manual shut-off valve in the gas line in an easily accessible location outside the cooktop. Be sure you know how and where to shut off the gas supply to the cooktop. Install the electrical outlet 12″ below the countertop. ELECTRICAL CONNECTION: This cooktop features pilotless electric ignition for energy savings and reliability. -
Page 12: Dimensions And Clearances
Cut the opening in the countertop. To ensure accuracy, it is best to make a template for the opening. Make sure the sides of the opening are parallel also rear and front cuts are exactly perpendicular to the sides. Observe all minimum clearances. Observe all minimum clearances. Observe all minimum clearances. FI310 Series FI640 Series FI850/950 Series FI310 Series FI640 Series... -
Page 13: Installation Instructions
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTI INSTALL THE COOKTOP Remove the screws on the sides of the cooktop burner box. Use those screws to attach the side mounting brackets. Remove the screws on the sides of the cooktop burner box. Use those screws to attach the side mounting brackets. Insert the cooktop centered into the cutout opening. -
Page 14: Assemble Burners And Check Ignition
ASSEMBLE BURNERS AND CHECK IGNITION The electrode of the electronic ignition system is positioned above the surface of the burner base. Do not remove a burner cap or touch the electrode of a burner while another is turned on. Damage or electrical shock may occur. The electrode of the electronic ignition system is positioned above the surface of the burner base. - Page 15 Burner ignition. Cooktop Spark Ignition—When you turn the cooktop knob to LITE, the spark igniter makes a series of electric sparks (ticking sounds) which light the burner. During a power failure, the burners will not light automatically. In an emergency, a cooktop burner may be lit with a match by following the steps below. WARNING: Lighting gas burners with a match is dangerous.
-
Page 16: Lp Gas Conversion
LP GAS CONVERSION If sold outside the U.S. and Canada: WARNING: If you wish to use this product with Liquefied Petroleum (LP) gas containing greater than 10% bu- tane, you must purchase the butane conversion kit. SAFTY INFORMATION The pressure regulator and burner orifices are set for natural gas operation. To convert this cooktop from natural gas operation to LP operation, the regulator and burner orifices must be convert- ed. -
Page 17: Tools You Will Need
TOOLS YOU WILL NEED 1. ADJUST THE REGULATOR Disconnect all electrical power at the main circuit breaker or fuse box. Shut off the gas supply to the appliance by closing the manual shut-off valve. Adjust the pressure regulator by doing the following: FIGURE A FIGURE B For Natural Gas usage the retainer pin will look like this. - Page 18 2. CHANGE BURNER NOzzLES 2. CHANGE bURNER NOZZLES INSTALLATION TIP: First remove all nozzles and then start replacing them. This will help to prevent the possi- INSTALLATION TIP: First remove all nozzles and then start replacing them. This will help to prevent the pos- bility that some may not be replaced.
- Page 19 LIQUID PRETROLEUM (LP) GAS NOZZLES LIQUID PRETROLEUM (LP) GAS NOZZLES LIqUID PRETROLEUM (LP) GAS NOzzLES POSITION NOZZLE MINIMUM MAXIMUM RATE BURNER POSITION NOZZLE MINIMUM MAXIMUM RATE BURNER DIAMETER PRESSURE PRESSURE (BTU/H) DIAMETER PRESSURE PRESSURE (BTU/H) Auxiliary Front Right 1 x 0.70 10”...
-
Page 20: Setting The Minimum Flame
SETTING THE MINIMUM FLAME SETTING THE MINIMUM FLAME The flame on the small output is regulated by the factory. When the injectors have been replaced or there are special mains pressure conditions, it may be necessary to regulate the minimum flame again. The operations necessary to set The flame on the small output is regulated by the factory. - Page 22 ATE INSPECTION of your Fiore product for potential freight damage. Any claims for damage visible or hidden, must be made immediately in order for the carrier to assume full responsibility and absorb any associated costs. If damage or cosmetic defect is discovered DO NOT INSTALL your Fiore product. Any claimed damage or defect...
- Page 23 Defects and damages arising from transportation of the product to the home of the owner and other acts of God. Fiore does not assume any responsibility for incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages; therefore, the above limitation or exclusion may...
- Page 24 ™ The appliances are for household use only.
Need help?
Do you have a question about the FI310 and is the answer not in the manual?
Questions and answers