Subscribe to Our Youtube Channel
Summary of Contents for Zultys BPS12
- Page 1 BPS12 Battery Power Supply Hardware Manual Manual Part Number 90-18020 Zultys Technologies 771 Vaqueros Avenue Sunnyvale, CA 94085 tel: +1-408-328-0450 fax: +1-408-328-0451 http://www.zultys.com...
-
Page 2: Revision History
This document contains proprietary information which is protected by copyright. The contents of this manual and the associated software are the property of Zultys Technologies, and all rights are reserved. No part of this document may be photocopied, reproduced, stored in any computer format, translated to another language, or publicly displayed without the prior written consent of Zultys Technologies. -
Page 3: Table Of Contents
Installing the BPS12........ - Page 4 Index ..........39 ii BPS12 Hardware Manual...
-
Page 5: Introduction
Scope 1.1.1 Audience This manual is intended for properly trained service personnel and technicians who need to install the BPS12 Battery Power Supply. The manual assumes you are familiar with electronic circuitry and wiring practices. 1.1.2 Installation and Use Unpack the product and verify the items as described in chapter 3, starting on page 11. -
Page 6: Ordering Information
1.1.4 What this Manual Does Not Include This manual does not describe the features and functionality of the BPS12. The manual does not discuss technology details, pricing, names of sales representatives, or names of distribution channels. Access the Zultys web sites for all further information. Zultys is very open about its products and most of the manuals are available on line at: http://www.Zultys.co.uk... -
Page 7: Documentation Overview
BPS12. Warning This notice indicates that if a specific procedure or practice is not correctly followed, permanent damage to the BPS12 and personal injury may result. Danger This notice warns you of imminent hazard to yourself and others if proper... -
Page 8: Forms Of Documentation
The printed version of this manual is updated as required. 1.4.2 This manual is available in PDF format. You can download the PDF file from the Zultys web site http://www.zultys.com You can obtain old versions of the manual that may describe the hardware that you have, the manual that was used to produce the most recently printed manual, or the latest manual that describes all the latest features of the product. -
Page 9: Warranty, Service, And Support
BPS12 and surrounding equipment. You can install the BPS12 yourself or arrange for someone else to install it for you. Zultys does not offer installation. If you purchased the BPS12 from a VAR or distributor they will be able to offer you installation services. -
Page 10: Warranty
Zultys Technologies (Zultys) provides a warranty to the purchaser of its products as outlined below. For purchases made in the USA, Canada, the UK, China, and Australia, the purchaser is the end user. For all other sales, the purchaser is Zultys’ reseller or distributor, who has sold you, the end user, the product. - Page 11 For warranty service or repair, this product must be returned to a service facility designated by Zultys. Zultys may repair on-site at the option of the Buyer. The Buyer is then responsible for travel charges and applicable additional expenses for such services.
-
Page 12: Support
This section suggests ways to save yourself time by checking for answers yourself and ruling out common problems. If you have a question about the way the BPS12 works, the best way to get an accurate, immediate answer is to try one or all of these approaches first. - Page 13 2.4.3.3 Calling Technical Support Be prepared when you call. When you call to speak to Zultys technical support, you are likely to get an immediate resolution to your problem if you are ready with certain types of information: E-mail a problem report in advance of calling. Allow Zultys technical support at least four hours to review your e-mail.
- Page 14 BPS12 Hardware Manual Use Zultys’ technical support to solve problems that you have tried diligently to solve by yourself. You may contact Zultys’ technical support at the following number. You must pay for any phone charges: +1-408-328-0450...
-
Page 15: Receiving The Equipment
3.2.1 Verify Contents There are few hardware options for the BPS12. Upon delivery of your system, inspect the packing list, and confirm that all items listed on that note were received. Compare the packing slip with your purchase order. Your BPS12 is usually shipped with an ac power cord, one battery power cable, rack mount brackets, and sufficient screws to securely mount the power supply to your equipment rack. -
Page 16: In Case Of Damage Or Malfunction
Zultys. Distributors will offer their own service and support for Zultys’s products. 3.4.3 Describing the Problem If you are returning equipment to Zultys for service, attach a tag or sheet of paper to the equipment giving the following details: • your company or institution’s name, address, and phone number... - Page 17 The method of shipment which Zultys will return repaired merchandise back to your facility will be the same method by which you shipped the merchandise to Zultys. For example, if you shipped merchandise to Zultys by ground shipment, Zultys will return the merchandise to you by ground shipment.
- Page 18 BPS12 Hardware Manual...
-
Page 19: Chapter 4 Hardware Description
Front Side of the BPS12 The front side of the BPS12, shown in figure 4-1, displays the BPS12 label on the right side of the panel and features three LEDs in the upper left corner. This side contains no wiring connectors. - Page 20 4.2.2 Rear Side of BPS12 The rear side of the BPS12, shown in figure 4-2, is the side that has the power connectors, fuses, and standby switch. The numbers in the figure correspond to the following descriptions: T16 AH, 250V...
-
Page 21: Status Indicators
4. Hardware Description Status Indicators The BPS12 provides three LEDs on the front and rear panels to inform you of device status and an audio alarm to alert you of conditions that require your attention. The front and rear panel LEDs are equivalent and always display the same status messages. -
Page 22: Status Led
When a condition causes all LEDs to flash red, the LEDs will continue to flash red for a minimum of 32 seconds before the system shuts down. The BPS12 flashes all LEDs red and buzzes the audio alarm continuously under the following conditions:... -
Page 23: Bps12 Capacity
4.4.1.1 Load supply When the main ac power is on, a single BPS12 can supply –56 Vdc nominal, 10 A maximum to an individual load or distributed among all loads. 4.4.1.2... - Page 24 A fully charged BPS12, at room temperature, can discharge a current of 0.6 A for 20 hours, which equals a battery capacity of 12 Ah. However, the same BPS12 can discharge a current of 8 A for only one hour, for a battery capacity of 8 Ah.
-
Page 25: Installing The Bps12
• the instructions for attaching the BPS12 to an equipment rack The BPS12 was designed to be permanently installed within a network room in a 19" equipment rack. You must carefully install the BPS12 system to ensure its proper operation. -
Page 26: Preparation For Installation
The combined load current for systems connected in parallel must not exceed 10 A. 1. You may purchase extender brackets if the equipment bay is 23" instead of 19". Check with your Zultys representative for the part number and pricing of these brackets. -
Page 27: Installation
The BPS12 has a universal ac input that you can connect to a standard electric outlet (90 Vac to 264 Vac, 47 Hz to 63 Hz). The BPS12 draws a maximum current of 9.3 A from its ac input. 5.2.1.6 Cable Lengths You need to install the BPS12 so that you can run the battery supply cable to your load. - Page 28 Devices that connect to the BPS12 are likely to be the MX250, MX1200, the LAN switch, and other BSP-12s. All connections to the BPS12 are made at the rear side of the system. Leave space at the rear of the system for cables and for personnel installing the system.
-
Page 29: Mounting Brackets
BPS12 to appear at the front of the equipment rack. When mounting the bracket on the front end of the chassis, orient the front flange of the bracket so that it is flush with the front panel of the BPS12, as shown in figure 5-4 BPS12... - Page 30 Mounting brackets on the rear of the chassis – You can attach the flange to the Rear Bracket holes; orient the front flange of the bracket so that it is flush with the rear panel of the BPS12, as shown if figure 5-5.
- Page 31 Once mounted in position with the screws in place, use a power screwdriver to tighten all four screws. 1. The BPS12 is supplied with four 12-24 mounting screws for conventional 19” equipment racks. Zultys supplies M6 screws for metric threaded racks.
- Page 32 BPS12 Hardware Manual...
-
Page 33: Powering And Connecting The Bps12
BPS12 to an ac power source and the expected response from the BPS12. To connect the BPS12 to an ac source, verify that the standby switch is pressed in the O position. Plug the ac cord into ac input located in the bottom left corner of the BPS12, as shown in figure 6-1. - Page 34 LED will turn green when charging is complete. Danger You must use only the power cord supplied by Zultys when connecting this system to ac power. If this is not suitable, contact your Zultys sales or service representative. The power cord that is provided has a separate ground (earth) connector, and you must insert it into a power socket that is provided with a protective ground (earth) contact.
-
Page 35: Connecting The Bps12 To An Mx250 Or Mx1200
You can connect up to five BPS12 units for a maximum discharge capacity (at 0.6 A) of 60 Ah. - Page 36 BPS12 Hardware Manual To connect two BPS12 units together, plug each end of a Power Cable into a dc power output in each unit. You can use any dc power output on each chassis when connecting the two BPS12 units...
-
Page 37: Maintenance And Use
Only trained and qualified personnel should be allowed to maintain the BPS12. Servicing The only user serviceable parts on the BPS12 are the seven fuses that are accessible from the rear panel. This section describes the method of diagnosing possible fuse failures and the method of replacing the fuses. -
Page 38: Replacing Fuses
45°. The receptacle is spring loaded and will pop out of the chassis. Replace the fuse only with a 10 A fuse supplied with the BPS12 by Zultys – 35-10008-00. Place the new fuse in the receptacle and then return the receptacle into the chassis. -
Page 39: Disposal
7. Maintenance and Use For proper service of the BPS12, return it to the distributor from whom you purchased it or to Zultys. Disposal When the system is no longer of any use, you may return it to Zultys, or the Zultys distributor... - Page 40 BPS12 Hardware Manual...
-
Page 41: Regulatory And Safety Compliance
A p p e n d i x A Regulatory and Safety Compliance The BPS12 complies with the following agency approvals and standards. Safety UL 60950, CSA-C22.2, AS/NZ 60950:2000, EN60950. EMC Emission FCC Part 15, ICES-003, AS/NZS 3548, CISPR 22, EN55022, EN61000-3-2, EN61000-3-3. - Page 42 BPS12 Hardware Manual...
-
Page 43: Index
....11 – procedure ....21 returning to Zultys ... 12 BPS12 Hardware Manual 39... - Page 44 Index 40 BPS12 Hardware Manual...
Need help?
Do you have a question about the BPS12 and is the answer not in the manual?
Questions and answers