Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for LT Security 87XXT-HT series
Summary of Contents for LT Security 87XXT-HT series
- Page 1 Network Video Recorder Quick Start Guide Available from A1 Security Cameras www.a1securitycameras.com email: sales@a1securitycameras.com...
-
Page 2: Table Of Contents
Quick Start Guide of Network Video Recorder TABLE OF CONTENTS Chapter 1Description of Panels......................... 8 Front Panel ............................8 Rear Panel............................10 Chapter 2Installation and Connections ......................11 NVR Installation..........................11 Hard Disk Installation ........................11 RS-485 and Controller Connection ....................13 HDD Storage Calculation Chart...................... - Page 3 Quick Start Guide of Network Video Recorder Quick Start Guide This Manual is applicable Hybrid Network Video Recorder (NVR). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
-
Page 4: Regulatory Information
Quick Start Guide of Network Video Recorder Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 5: Safety Instruction
Quick Start Guide of Network Video Recorder Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. - Page 6 Quick Start Guide of Network Video Recorder Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
- Page 7 Quick Start Guide of Network Video Recorder Applicable Models This manual is applicable to the models listed in the following table. Series Model Type 87XXT-HT Network Video Recorder series 16CH Available from A1 Security Cameras www.a1securitycameras.com email: sales@a1securitycameras.com...
- Page 8 Quick Start Guide of Network Video Recorder Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
-
Page 9: Chapter 1Description Of Panels
Quick Start Guide of Network Video Recorder Chapter 1 Description of Panels 1.1 Front Panel Figure 1. 1 Front Panel Table 1. 1 Description of Front Panel Name Function Description POWER: the POWER indicator turns green when NVR is powered up. READY: The indicator light is green when the device is running normally. - Page 10 Quick Start Guide of Network Video Recorder Name Function Description Exit and back to the previous menu. Enter numeral “5”; Enter letters “JKL”; 5/JKL/EDIT: Delete characters before cursor; Check the checkbox and select the ON/OFF switch; Start/stop record clipping in playback. Enter numeral “6”;...
-
Page 11: Rear Panel
Quick Start Guide of Network Video Recorder Name Function Description Receiver for IR remote. IR Receiver 1.2 Rear Panel Figure 1. 2 Rear Panel Table 1. 2 Description of Rear Panel Item Description VIDEO IN BNC interface for TVI and analog video input. VIDEO OUT BNC connector for video output. -
Page 12: Chapter 2Installation And Connections
Quick Start Guide of Network Video Recorder Chapter 2 Installation and Connections 2.1 NVR Installation During the installation of the NVR: 1. Use brackets for rack mounting. 2. Ensure there is ample room for audio and video cables. 3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter. 4. - Page 13 Quick Start Guide of Network Video Recorder Figure 2. 2 Connect the Data Cable 3. Connect the power cable to the HDD. Figure 2. 3 Connect the Power Cable 4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD. Figure 2.
-
Page 14: Rs-485 And Controller Connection
Quick Start Guide of Network Video Recorder 2.3 RS-485 and Controller Connection Typical Connection : Figure 2. 5 Controller Connection A To connect PTZ to the NVR: 1. Disconnect pluggable block from the RS-485 terminal block. 2. Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part. -
Page 15: Hdd Storage Calculation Chart
Quick Start Guide of Network Video Recorder 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K... -
Page 16: Chapter 3Menu Operation
Quick Start Guide of Network Video Recorder Chapter 3 Menu Operation 3.1 Menu Structure The menu structure varies according to different models. Menu Playback Maintenance Shutdown Export VCA Search Record Camera Configuration Manual Behavior Normal Normal Schedule Camera General System Info Logout Record General... -
Page 17: Activating Your Device
Quick Start Guide of Network Video Recorder After the device starts up, the wizard will guide you through the initial settings, including modifying password, date and time settings, network settings, HDD initializing, and recording. To shut down the NVR: 1. Enter the Shutdown menu. Menu >... -
Page 18: Login And Logout
Quick Start Guide of Network Video Recorder For the old version device, if you upgrade it to the new version, the following dialog box will pop up once the device starts up. You can click YES and follow the wizard to set a strong password. Figure 3. -
Page 19: User Logout
Quick Start Guide of Network Video Recorder Figure 3. 6 User Account Protection User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to perform any operations, you need to enter user name and password log in again. Steps: Enter the Shutdown menu. -
Page 20: Using The Setup Wizard
Quick Start Guide of Network Video Recorder Figure 3. 8 Configure Signal Input Type Click Apply to save the settings. Each two video channels are grouped in sequence, e.g., CH01 and CH02, CH03 and CH04..., and each two channels in the same group must be connected with the same type of video source selected on GUI. For example, when the TVI/CVBS signal mode is selected, then either TVI or CVBS signal input can be connected to the channels in the same group;... -
Page 21: Network Settings
Quick Start Guide of Network Video Recorder Figure 3. 9 Wizard 3.7 Network Settings Purpose: Network settings must be properly configured before you operate NVR over network. Steps: 1. Enter the Network Settings interface. Menu > Configuration > Network Figure 3. 10 Network Settings 1 self-adaptive 10M/100M/1000M network interface or 1 self-adaptive 10M/100Mbps network interface provided for LTN87XXT-HT. -
Page 22: Adding Ip Cameras
Quick Start Guide of Network Video Recorder Gateway, MTU and DNS Server. If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server. 4. After having configured the general settings, click the Apply button to save the settings. 3.8 Adding IP Cameras Purpose: Before you can get live video or record the video files, you should add the network cameras to the connection list... -
Page 23: Live View
Quick Start Guide of Network Video Recorder Figure 3. 12 Add IP Camera Select the detected IP camera and click the Add button to add it directly, and you can click the Search button to refresh the online IP camera manually. Ÿ... -
Page 24: Playback
Quick Start Guide of Network Video Recorder After rebooting all the manual records enabled are canceled. Steps: 1. On the live view window, right lick the window and move the cursor to the Start Recording option, and select Continuous Record or Motion Detection Record on your demand. 2. -
Page 25: Chapter 4Accessing By Web Browser
Quick Start Guide of Network Video Recorder Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. - Page 26 Quick Start Guide of Network Video Recorder After login, you can perform the operation and configuration of the device, including the live view, playback, log search, configuration, etc. Available from A1 Security Cameras www.a1securitycameras.com email: sales@a1securitycameras.com...
Need help?
Do you have a question about the 87XXT-HT series and is the answer not in the manual?
Questions and answers