Page 2
Introduction Thanks for purchasing this hunting camera which is an professional product for recording and observing the wildlife. We provide detail user manual for your reference. Please read this manual carefully before first use. We are serious and strict when writhing the manual. While the errors and omissions may exist during printing process.
Page 3
This document is subject to copyright protection. Any other copy without prior written permission of our company is not allowed. Our company reserve all the right for the final interpretation of this user manual,three guarantees and relative documents. Safety Please read below safety precautions carefully before using the camera.
Parts Of The Camera 1. Up/Video Button 2. Right Button 3. Shot Button 4. OK Button 5. Left Button 6. Menu Button 7. Replay Button 8. Down/Capture Button 9. Micro SD Card Slot 10. AV Jack 11. USB Jack 12. OFF 13.
14. ON 15. Display Screen 16. Infrared LEDs 17. Lens 18. Motion Sensor Power Supply Please install batteries before using the camera. ♦ Open the camera case and remove the battery cover. Install 8 pieces of 1.5V AA batteries. Please make sure the electrode is correct.
♦ If the camera is in low power, please connect the camera to a power adapter(not provide) for power supply. Inserting The Memory Card The camera has no built-in memory. Please prepare a Micro SD card and insert it into the camera for saving files.
Page 7
♦ Do not insert the memory card forcibly. Please refer to the marking on the camera. ♦ For the first time use, please wait for the memory card temperature reach the ambient temperature.The camera will be short-circuit influenced by environment temperature and humidity.
Basic Operation Turn On And Off The Camera Switch the Mode Button to“Test/On”to turn on the camera. Switch the Mode Button to “Off” to turn off the camera. System Setup Switch Mode Button to“Test”, then you can set the system parameters. 1.
Page 9
3. Press Up/Down button to scan all menu. Then press OK button to enter the options interface. 4. Press Up/Down button to scan all options. And press OK button to confirm options. 5. Press Menu button again to turn back to last menu or exit the setup menu.
Page 10
Photo Resolution Set the still image resolution.The bigger the resolution is ,the higher the sharpness is. It will take bigger space either. Options:【12MP(4000x3000P)】/ 【8MP(3264x2448P)】/【5MP(2592x1944P)】/ 【3MP(2048x1536P)】/【1MP(1280x960P)】. Photo Series Set the photo number of continuous shooting. In photo mode, the camera will take photos continuously.
Page 11
Video Resolution Set the video resolution. The bigger the resolution is ,the longer the video time can be stored. Options: 【1920x1080P】 / 【 1280x720P】 / 【 720x480P】 /【640x480P】/【320x240P】. TL Video Resolution Set the resolution of time lapse video . Options:【2592x1944P】/【2048x1536P】. Video Length Set the duration of recording a video clip.
Page 12
Audio Recording Open this function,the camera will record audio when recording video. Options:【On】/【Off】. Shot Lag Set the time of delay shooting when the camera detects the motion. Within the selected time, the camera will not record any image or video. It can avoid to store too much same event and save more capacity.
Page 13
Sensitivity Motion Sensors Set the sensitivity of the sensor. Environmental impact is small indoors, you can choose “Low”. In outdoor, choose “Middle”in normal condition. Choose “High”if the environment impact is huge outdoors. The temperature can also influence the sensor sensitivity. “High Sensitivity”applies to mild environment.
Page 14
camera will work just in the stated time slot. In other time, the camera will keep in standby state. Options:【On】/【Off】. Target recording time Start: Stop: Hr:Min Hr:Min 00 00 MENU Back OK Select Time Lapse In Time lapse menu, there are three options as below.
Page 15
[Normal]: The camera will take pictures automatically as per set time interval. For example,set the interval time to 1 hour, the camera will take a photo each hour. If you want to observe that a plant blooms, the camera will take 24 photos in 24 hours to record the whole process of blooming.
Page 16
hours,there will be 24 photos. These photos will be converted into a video. Settings Set time lapse Hr:Min :Sec Notification:Motion sensors deactivated MENU Back OK Select [Off]: Close the time lapse function. Language Set the language display on screen. Options: 【English】 / 【 German】 / 【 Danish】 / 【 Finnish】...
Page 17
/ 【 Swedish】 【Spanish】 / 【 French】 / 【 Italian】 / 【 Dutch】 / 【Portuguese】 / 【Simplified Chinese】 / 【Japanese】 . Time & DateSet the date and time of camera. The date format: dd/mm/yyyy, yyyy/mm/dd, mm/dd/yyyy. The time format: 24h,12h. Press Left/Right button to choose the item.Press Up/Down button to adjust the value.
Page 18
Password Protection Set the power-on password of the camera. The password is four digits,each digit ranges from 0 to If you forget the password, please reset the camera. Then all parameters will reset to the factory settings. Options:【On】/【Off】. Beep Sound Open/close the button sound.
Page 19
card that has been used in another device previously ,please format the memory card. Options:【Yes】/【No】. Serial NO. Set the unique serial number for the camera. The number is four digits, each digit ranges from 0 to 9. Options:【On】/【Off】. Reset Settings Restore the camera to factory default settings including password,serial number and so on.
Page 20
Take Photos ,Record Video ,Playback Switch the Mode Button to “Test”. In this mode,you can take photos, record video and playback files manually. ♦ Take Photos:Press Capture button to switch to photo mode. Press Shot button to take a picture. ♦...
Page 21
have a pause. Press Menu button to stop playback. Press Playback button again to exit the playback mode. Playback Menu: 1) Delete current file:Delete the current photo or video. Options:【Cancel】/【Delete】. 2) Delete all files: Delete all photo and video files in the memory card.
Working Mode Switch the Mode Button to “On”. After turn on the camera,the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode. If the wild animals enter the detection range of the motion sensors , the camera will be activated and detect the motion trail.
When the wild animals leave the detection zone of the sensors , the camera will be deactivated and turn back to standby mode. Night Mode During the night,the infrared LEDs will turn on automatically ,to provide necessary light for taking pictures.
When record a video for long time in the evening, the low voltage may have a great influence on the stability of the machine. Do not record video with low voltage in the evening. Using the wall bracket You can mount the camera on a wall or tree by the supplied wall bracket.
Page 26
■ Phillips head screwdriver Caution ♦ Ensure that there are no electric lines, water or heating pipes installed at the proposed drilling location. ♦ The supplied wall plugs are only suitable for mounting on concrete or stone. Before starting the installation, please check your installation location carefully for its suitability for the plugs.
Install Steps ♦ Mark the drill holes by holding the foot of the wall bracket at the desired mounting location and marking the hole positions. ♦ Use a drill with a 6 mm drill bit to drill the required holes and insert the plugs and insert the wall plugs flush with the wall.
Page 28
the two pivot bolts a little, position the camera and fix the position by tightening the two pivot bolts . Connecting To TV The camera can transfer the video signal to an external monitor or a television. Please follow below instructions to operate. 1.
Page 29
The image will show on the TV. Download Files To Computer There are two ways to download files from the memory card to a computer: By inserting the memory card into a card reader By connecting the camera to a computer using the supplied USB cable.
Page 30
represents the memory card. 3. Copy image or video files from the memory card to your computer. Connecting the Camcorder to a PC by the USB Cable 1. Connect the camera to the computer via USB cable.Turn on the camera,the screen will display” MSDC“.
Need help?
Do you have a question about the CVAIC-OG72 and is the answer not in the manual?
Questions and answers