Table of Contents
Advertisement
Please dispose of packaging for the product in a responsible
manner. It is suitable for recycling.
Help to protect the
environment, take the packaging to the local amenity tip
and place into the appropriate recycling bin.
01938
12"x 36" Wood Lathe
Never dispose of electrical equipment or batteries in with
your domestic waste. If your supplier offers a disposal facil-
ity please use it or alternatively use a recognised re-cycling
agent. This will allow the recycling of raw materials and help
protect the environment.
Please read and fully understand the instructions in
FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR.
this manual before operation. Keep this manual
safe for future reference
Ref:101027
24
1
Advertisement
Table of Contents
Summary of Contents for SIP 01938
- Page 1 Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate recycling bin. 01938 12”x 36” Wood Lathe Never dispose of electrical equipment or batteries in with your domestic waste. If your supplier offers a disposal facil- ity please use it or alternatively use a recognised re-cycling agent.
- Page 2 NOTES...
- Page 3 PARTS LIST….cont CONTENTS Ref No. Description Ref No. Description Cap Head Bolt (M10 x 25) Washer (8 mm) 53-1 Lock washer (10 mm) Nut (M8) Page No. Description 54-1 Stand-Leg A Mains Lead Contents 54-3 Stand-Top Plate Digital Readout General Safety Instructions 54-4 Stand-Long Support Label-A...
-
Page 4: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS PARTS LIST 1. KNOW YOUR POWER TOOL. Read this instruction manual carefully. Learn the tool's Ref No. Description Ref No. Description applications and limitations, as well as its specific potential hazards. Headstock C-Ring (S16) 2. KEEP GUARDS IN PLACE and in working order, never use the tool if any damage is present. - Page 5 EXPLODED DRAWING...cont GENERAL SAFETY INSTRUCTIONS….cont 20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rota- tion of the blade or cutter only. 21. NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN the power off. Don't leave the tool until it comes to a complete stop.
-
Page 6: Specific Safety Instructions
SPECIFIC SAFETY INSTRUCTIONS EXPLODED DRAWING Caution! If used incorrectly, woodworking machines can be dangerous; for this reason always comply with the safety instructions mentioned in this manual. WARNING: Do not operate your wood lathe until it is completely assembled and in- stalled according to the instructions. -
Page 7: Maintenance
MAINTENANCE SPECIFIC SAFETY INSTRUCTIONS….cont WARNING - FOR YOUR OWN SAFETY; ALWAYS TURN THE LATHE OFF AND DISCONNECT IT WARNING! Before connecting the tool to the mains supply be sure that the FROM THE MAINS SUPPLY BEFORE PERFORMING ANY MAINTENANCE OR LUBRICATION voltage supply is the same as that specified on the nameplate of the tool. -
Page 8: Technical Specifications
2 Morse Taper ternatively close the yellow cover. CONTENTS AND ACCESSORIES Your variable speed SIP wood lathe is fitted with a safety NVR (No Volt Release) switch. This means that if power is cut to the lathe (such as in a power failure); the motor will not start to run... -
Page 9: Getting To Know Your Wood Lathe
OPERATING INSTRUCTIONS….cont GETTING TO KNOW YOUR WOOD LATHE Operating The Tailstock: • Move the tailstock (1) by loosening the tail- stock lock lever (2) and sliding the tailstock assembly to the desired position on the lathe bed. Securely lock the tailstock into position by tightening the lock lever. - Page 10 OPERATING INSTRUCTIONS Guarantee: Operating tips: This SIP wood lathe is covered by a 24 month parts and labour warranty covering fail- 1. Make sure cutting tools are sharp and clean for best performance and safe opera- tion. ure due to manufacturers defects. This does not cover failure due to misuse or operat- ing the machine outside the scope of this manual.
-
Page 11: Electrical Connection
Installing The Faceplate: Connecting to the power supply: This SIP wood lathe is fitted with a standard 230v ~ 13 amp plug. Before using the Remove the headstock spur from the spindle by lathe, inspect the mains lead and plug to ensure that neither are damaged. If any using the push rod. - Page 12 ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS….cont CAUTION: The lathe is a heavy machine and must be lifted with assistance to assem- Fitting The Headstock Locking Handle: ble the lathe to the leg set. • Locate and assemble the head locking • Separate the leg set parts. handle (1), spring (2) and Allen bolt (3) as •...
Need help?
Do you have a question about the 01938 and is the answer not in the manual?
Questions and answers