Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for meywalk 2000
- Page 1 User manual meywalk ® 2000 Model Small, Medium and Large...
-
Page 2: Table Of Contents
Contens These instructions for use contain information on the assembly and adjustment of MEYWALK® 2000, how to maintain it, things to watch out for and other important items. Introduction Prior to first use Joining the top part and bottom frame... -
Page 3: Introduction
Both user and helper will stand up without support from a seat. find it much less tiring to get in and out of the MEYWALK® 2000 than MEYWALK® 2000 can be adjusted to other walking aids. Due to the large give a good and individually fitted wheels MEYWALK®... -
Page 4: Prior To First Use
Prior to first use The height of the trunk support is al- Prior to first use MEYWALK® 2000 is tered by loosening the bottom two supplied almost fully assembled. Allen screws and then the bottom Check that the package contains the two spanner grips. -
Page 5: Trunk Support Locking
Trunk support locking: When closing the trunk support one can “lock” the two rear tubes by giv- ing them a firm push downwards. In this way one can secure them from accidently slide open or being opened by “a busybody” ! Seat position and angle: The seat can be adjusted forwards or backwards by slackening the Allen... -
Page 6: Rea Stop
MEYWALK® the way back until they come to a the external tube. After adjustment, 2000 and raise the tilt bar. -
Page 7: Mounting An Adjustmedt Of Accessories
Accessories: Anti-tip: Height reduction fitting: Anti-tip supports are mounted on The trunk support and seat height each side by first removing the cen- can also be reduced approximately 8 tercap on the outside of the rear cm (3”) with a set of height reduction wheel and unscrewing the nut from fittings. -
Page 8: Swivel Lock On Front Casters
Swivel lock on front casters: Leg separation plate: The crossbar for the leg separation The swivel locks are delivered mounted on two new front casters. plate is mounted between the front For mounting first remove the two wheels. The fittings at both ends of front wheels from the casters, use a 6 the crossbar are fastened with the mm Allen key here. -
Page 9: Leg Guides
After adjustment To mount the hip-pads first lift off the retighten the screws and grips. top part of MEYWALK® 2000 from the bottom frame. At each side Leg guides: unscrew and remove the Allen screw and the spanner grip from the Leg guides for MEYWALK®... -
Page 10: Mounting And Use Of Drag Brakes
Mounting and use of non- Mounting and use af drag bra- reverse brakes: kes. The non-reverse brakes are mounted The drag brakes are fitted on the out- inside of the existing brakes. Use a side of the existing brakes. Use a 10 10 mm spanner to unscrew the mm (13/32”) spanner to unscrew the nuts from the two bolts which fix the... -
Page 11: Sefety Precautions
Council Directive The spring system used in MEY- low the instructions on the polish . 93/42/EEC concerning medical de- WALK® 2000 can involve a certain vices. risk of the walking aid toppling over Checking for tightness: Meywalk® 2000 is tested by Berlin if used by a very restless user. -
Page 12: Technical Data
Technical data Dimensions: Small Medium Large Length: 85 cm 95 cm 95 cm External width: 68 cm 70 cm 70 cm Internal width: 48 cm 48 cm 48 cm Seat height: 48-66 cm 62-86 cm 76-100 cm Trunk support height: 81-100 cm 94-117 cm 108-131 cm...
Need help?
Do you have a question about the 2000 and is the answer not in the manual?
Questions and answers