Summary of Contents for HomeGuardian 4902013
- Page 1 4902001/2/4/8/9/12/13 are only compatible to our main security system 4902000 (HWS100) ONLY. Installation and operating instructions...
- Page 2 Under the alarm mode, once the main control unit receive the signal from any sensors, it will send a signal to the auto dialer at the same time. Once the auto dialer receive it and was triggered by an emergency,...
- Page 3 Remarks: *The dialer is not applicable to the ISDN, ADSL switch board phone connections.
- Page 5 SECTION 4 – ACTIVATING THE DIALER Congratulations.Your Auto Dialer plus is now ready to help in emergency situations.You can test how the Dialer works by pressing both # and * keys on the dialer’s keypad for the dialer to dial out to the phone numbers you have stored. SECTION 5 - INSTRUCTION FOR THE RECIPIENT There are several things that your call recipients should know in order to successfully receive and terminate an emergency call from your dialer.
-
Page 6: Section 7 - Maintenance
SECTION 6 - HOUSE SECURITY CODE AND ZONE CODE SETTINGS You can change the house security code on each sensor, panel and other modules of your security system to avoid interference with other systems. In most cases you will NOT need to change the factory settings of the house security code. If the Panel and sensors activate intermittently or do not work at all, you may be able to solve the problem by changing the house security codes on all system modules. - Page 7 IC Caution Statement Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This product meets the applicable Industry Canada technical specifications. Before the installation of this equipment, the users should assure that the equipment is allowable to be connected to the facilities of the local communications company.
- Page 8 If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
- Page 9 pound sign...
- Page 12 4902001/2/4/8/9/12/13 sont compatibles avec notre système de sécurité principal 4902000 (HWS100) SEULEMENT Installation et instructions d’opération...
- Page 13 Under the alarm mode, once the main control unit receive the signal from any sensors, it will send a signal to the auto dialer at the same time. Once the auto dialer receive it and was triggered by an emergency, it will silently send a pre-recorded message to up to 8-pre-programmed telephone numbers with the first 2 numbers being the priority phone number.
- Page 14 Remarks: *The dialer is not applicable to the ISDN, ADSL switch board phone connections.
- Page 18 Avertissement IC Son fonctionnement est soumis aux deux conditions suivantes : 1. Ce dispositif ne peut causer aucune interférence nuisible et 2. Ce dispositif doit accepter toute interférence reçue, y compris une interférence pouvant causer un fonctionnement non désiré.
- Page 19 This product meets the applicable Industry Canada technical specifications. Before the installation of this equipment, the users should assure that the equipment is allowable to be connected to the facilities of the local communications company. It must also be installed using an acceptable method of connection.
- Page 20 Step 1. To ENTER Press to activate the keyboard Enter setup SETUP mode Enter the 4-DIGIT PIN (Default PIN is "1234") mode for any Press to go into SETUP mode programming Step 2. To RECORD Press and hold for 2 seconds, until the Under message REC shows up on the screen to start the...
- Page 21 To ERASE a Press (Display will show "1" for 1st phone stored phone number),Repeat this step to choose which number phone numbers you wish to ERASE (1, 2, 3, 4, 5, 6, 7, 8) Press then to confirm erasing To program Press (Display will show "1"...
Need help?
Do you have a question about the 4902013 and is the answer not in the manual?
Questions and answers