COLOR TELEVISION RECEIVER Chassis : S62B(P)_SHINE Model : WS32Z306VBXXEC SERVICE Manual COLOR TELEVISION RECEIVER FEATURES Slimfit(Low Depth) CRT ■ ■ ■ SRS-WOW Simple 100Hz ■ ■ WS32Z306V...
When space between the part and the printed circuit board. voltage exceeds the specified limits, check each special Check the AC power cord for possible damages. Keep part. the part or the lead away from any heat-emitting materials. Samsung Electronics...
Page 6
Critical safety parts should be bracketed with ( Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
5. Check for insulation between the blade of the AC plug 10. The sharp edges of the metal material may cause and that of any conductive materials (i.e. the metal physical damage, so ensure wearing protective gloves panel, input terminal, earphone jack, etc). during the repair. Samsung Electronics...
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
5. Make sure to turn the power off and unplug the power cord from the outlet before removing the product. Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock. Samsung Electronics...
- VSP9402 : RF-CVBS,EXT-CVBS,FRONT Y,C,SCART1 R/G/B input and Video Signal Processing. - CXA2165 : H-out,VD-P,VD-N,RGB output,Video and Deflection Signal Processing. - STV8237 : Provides S-IF,Analog audio and Digital audio signal input and decoding functions. - SDA5550 : I2C-Comunication,Master Control Micom. - M27W201 : ROM Micom Samsung Electronics...
5. When replacing the CRT Ass'y : No adjustments required. 6. When replacing the front panel master power switch : No adjustments required. 7. When replacing the Side AV : No adjustments required. 8. When replacing the control switch : No adjustments required. Samsung Electronics...
Option (XX XX XX) Checksum(XXXX) Reset / XX-XX-XX 3. Functions of the Keys within Service Mode MENU Show all menus Move the cursor to select an item. ▲ / ▼ Adjust the selected configuration value ◀ / ▶ Samsung Electronics...
Adjust Angle V Position 2. Deflection Adiustment (NTSC) WS32Z306VB CW29Z306VB item Remark Data Data V Amp V_SHIFT H EW H Shift V Linearity Upper-Linearity Lower-Linearity V SC H Parablar Upper Corner Lower Corner H Trapezium Angle V Position Samsung Electronics...
Page 19
CR Offset CB Offest R Drive Adjust G Drive 32->38 B Drive Adjust Sub Bright Adjust Sub Contrast Adjust Sub Color Secam sub color Sub Tint CTI Level Color AXIS LTI Level 1->3 Melody volume Video mute time Samsung Electronics...
Page 20
PIP Tint PIP Color PIP Pal V Pos PIP NTSC V Pos PIP H Pos PIP R Cut off PIP G Cut off PIP B Cut off PIP R Drive PIP G Drive PIP B Drive PIP VSP Delay Samsung Electronics...
Page 21
8. Video Adjustment 5 WS32Z306VB CW29Z306VB item Remark Data Data R_Drive Warm2 B_Drive Warm2 R_Cutoff_Warm2 B_Cutoff_Warm2 R_Drive Warm1 B_Drive Warm1 R_Cutoff_Warm1 B_Cutoff_Warm1 R_Drive Normal B_Drive Normal R_Cutoff_Normal B_Cutoff_Normal R_Drive Cool1 B_Drive Cool1 R_Cutoff_Cool1 B_Cutoff_Cool1 R_Drive Cool2 B_Drive Cool2 R_Cutoff_Cool2 B_Cutoff_Cool2 Samsung Electronics...
Page 22
Standard Brightness Standard Shapness Standard Color Standard Tint Standard Color Tone Movie Contrast Movie Brightness Movie Shapness Movie Color Movie Tint Movie Color Tone Left Blanking (PAL) Right Blanking (PAL) Left Blanking (VGA) Right Blanking (VGA) Left Blanking (480p) Samsung Electronics...
Page 23
Range of B Gain Range of F/B Gain TTX V-Position TTX H-Position Pal Sensitivity (AV mode) wide model 4:3 Normal Parabola 1080i 50HZ Trepezium 1080i 60HZ Trepezium UP-UCG (Up Corner Semi Control) LO-UCG (Low Corner Semi Control) Vertical Slicing Level Samsung Electronics...
Page 25
OSD Language OSD Language Table TTX Language Group On : Australia,Newzealand 13 TTX List On / Off Off: Europe,CIS,Asia 14 Digital NR On / Off 15 AGC on/off On / Off 16 Blue Screen On / Off Samsung Electronics 3-11...
Page 26
Remark Data Data Data V Amp V_SHIFT H EW H Shift V Linearity Upper-Linearity Lower-Linearity V SC H Parablar Upper Corner Lower Corner H Trapezium Angle V Position CXA2151 Sub01 CXA2151 Sub02 Zoom1 Tra-offset Zoom2 Tra-offset 3-12 Samsung Electronics...
Page 27
Remark Data Data Data V Amp V_SHIFT H EW H Shift V Linearity Upper-Linearity Lower-Linearity V SC H Parablar Upper Corner Lower Corner H Trapezium Angle V Position CXA2151 Sub01 CXA2151 Sub02 Zoom1 Tra-offset Zoom2 Tra-offset Samsung Electronics 3-13...
Page 28
CIS 32" Asia 29" item Remark Data Data Data H Parablar_Pal Adjust Upper Corner_Pal Adjust Lower Corner_Pal Adjust Bow_Pal Angle_Pal H Shift_Pal Adjust H Parablar_NTSC Adjust Upper Corner_NTSC Adjust Lower Corner_NTSC Adjust Bow_NTSC Angle_NTSC H Shift_NTSC Adjust 3-14 Samsung Electronics...
Page 29
CIS 29" CIS 32" Asia 29" item Remark Data Data Data ABL Mode Gamma DPIC Level DC Trans ABL-TH VM-Level VM-Coring VM-f0 VM-Limit VM-Delay SHP CD SHP f0 SHP f1& p/o AKB Time Coring Bandpass Highpass Bandpass_AV Highpass_AV Samsung Electronics 3-15...
Page 30
10. Video Adjustment 4 CIS 29" CIS 32" Asia 29" item Remark Data Data Data 3Pip Pal V position 3Pip Pal H Position 3Pip Ntsc V Position 3Pip Ntsc H Position Sync Phase (480p) Sync Phase (576p) Sync Phase (1080i) 3-16 Samsung Electronics...
Page 31
R cutoff offset 576P G cutoff offset 576P R drive offset 480i G drive offset 480i R cutoff offset 480i G cutoff offset 480i R drive offset 576i G drive offset 576i R cutoff offset 576i G cutoff offset 576i Samsung Electronics 3-17...
Page 32
CIS 29" CIS 32" Asia 29" item Remark Data Data Data Sub Bright Sub Contrast Sub Color Sub Tint (Hue) Color AXIS LTI mode VM-Level VM-Coring VM-f0 VM-Limit VM-Delay SHP CD SHP f0 SHP f1& p10 LTI level 3-18 Samsung Electronics...
Page 33
SHP f1& p10 LTI level H_EHT comp_1080i V_EHT comp_1080i PIN EHT comp_1080i ABL TH_1080i 16. DTV Video Adjustment 2 CIS 29" CIS 32" Asia 29" item Remark Data Data Data EEP_GAMMA_480P EEP_DPIC_LEVEL_480P DC_TRANS_480P EEP_GAMMA_576P EEP_DPIC_LEVEL_576P DC_TRANS_576P EEP_GAMMA_1080I EEP_DPIC_LEVEL_1080I DC_TRANS_1080I Samsung Electronics 3-19...
Page 34
Standard Contrast Standard Brightness Standard Shapness Standard Color Standard Tint Standard Color Tone Movie Contrast Movie Brightness Movie Shapness Movie Color Movie Tint Movie Color Tone Left Blanking (PAL) Right Blanking (PAL) Left Blanking (VGA) Right Blanking (VGA) 3-20 Samsung Electronics...
Page 35
Range of B Gain Range of F/B Gain TTX V-Position TTX H-Position PAL Sensitivity (AV mode) wide model 4:3 Normal Parabola 1080i 50HZ Trepezium 1080i 60HZ Trepezium UP-UCG (Up Corner Semi Control) LO-UCG (Low Corner Semi Control) Samsung Electronics 3-21...
Page 37
Search LNA Sound 10 carrier mute 11 High Deviation 12 TTX Group Russian Russian West Europe Arabic TTX Language Group 13 TTX List On : Australia,Newzealand Off: Europe,CIS,Asia 14 TTX On/Off 15 AGC 16 Tilt 17 Hotel Mode Samsung Electronics 3-23...
② Press "Info → Menu → Mute → Power On" using the remote control and enter Factory Mode. ③ Enter Deflection Mode. ④ Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so that the width becomes 5 and the height becomes 4. 3-24 Samsung Electronics...
Page 39
⑦ When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed. If there is no change, finish the adjustments. Samsung Electronics 3-25...
After Adjustment Focus VR 6. Slowly turn the Dynamic Focus VR clockwise so that the 2nd line is the most clearly displayed. After Adjustment 7. Check the entire screen focus and repeat steps 3 to 6, if necessary. 3-26 Samsung Electronics...
Page 41
5. Adjust the Screen VR of FEB so that the highest point of the Pedestal Level is 175V. 175V Screen Adjust Method the Screen Voltage for Toshiba Pattern by Oscilloscope ※ Screen Voltage Measurement Data Item Data Required Adjustment The Highest Voltage among RK, GK and Screen Voltage Screen Voltage BK 175Vp-p-3V Samsung Electronics 3-27...
Page 42
4. When the adjustment is finished, check the following checklist. - If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again. - If there is a ghost line on the screen, adjust the Screen Voltage again. 3-28 Samsung Electronics...
Exploded View & Part List 4. Exploded View & Part List 4-1 WS32Z306VBXXEC You can search for the updated part code through ITSELF web site. URL:http://itself.sec.samsung.co.kr Loc.No. Code No. Description Specification Q'ty SA/SNA Remark CIS3 BP64-00331B DECORATION-POWER PJTV,ABS,HB,GR503,SVM30 S.N.A CIS7...
Electrical Part List You can search for the updated part code through ITSELF web site. URL:http://itself.sec.samsung.co.kr 5. Electrical Part List 5-1 WS32Z306VBXXEC Loc.No. Code No. Description Specification Q'ty SA/SNA Remark ASSY CHASSIS M0017 AA91-09381A ASSY CHASSIS WS32Z306VBXXEC,S62B,SHINE S.N.A T0098 AA94-15114A...
2) Check that the Master Switch has been pressed. 3) Check that the transmitter is turned on. 4) Check that transmitter device selection is set to TV. 5) Check that the signal cable is properly connected. 6) Check that channel setting has been set. Samsung Electronics...
Page 65
When the screen is not properly displayed and the left or right side of the picture is shrunk, or the top or bottom of the screen is expanded or shrunk, check if the Deflection Board is out of order. Samsung Electronics...
Page 66
I s a CRT high vo lt age been measured? Main Board I s t he cabl e f rom t he Connect t he cabl e Main Boar d t o t he CRT Ass' y proper l y connect ed? Samsung Electronics...
You can check the checksum according in the following order. Factory Mode → Checksum → Right Button → Calculate Checksum → Output Checksum (e.g. 0xab2b) ■ Checksum Examples T_COREOAKR1_1010 : checksum = 0xab2b T_COREOAKR1_1014 : checksum = 0x4faa Samsung Electronics...
Q406 H-OUT TR Open Line Materials Materials Change Q804 Materials (VCC_5V_C) F-Box Check and Change the Module B+(132V) Line F/BACK LINE Change No-Power CHECK Materials Repair End IC804 Q406 IC501S TU01S F/BOX FP801S POWER CORD IC301S IC803S IC601 Samsung Electronics...
- If no signal is received even though the RF signal from the external aerial is connected to the MAIN Board Tuner, check the following items. - Supply Power: 5V, 9V, 33V - Check for an RF defect: Check the CVBS output - Check for an AUDIO defect: Check the SiF Signal output Samsung Electronics...
Page 73
It receives the EXT1/EXT2/signal and consists of monitor output (video and audio). The signal is input to VSP9402 through the port. If no signal input/output is detected, check the following items. - Power supply : VSP9402(3.3V,1.8V) , CXA2180(5V) - Check if the input and output jacks are defective. 6-10 Samsung Electronics...
Page 74
The signal is received from the Audio Processor (MSP3421G) and sound is output at 10W + 10W power. - Power supply :15V - Check for input defects : L/R - Check for output defects : L+, L-, R+, R- Samsung Electronics 6-11...
Page 75
4. STV8237(Audio Processor) Diagnosis It processes the SIF and SCL 1/2 signal output from the Tuner. - Power supply : 3.3V,1.8V,9V , 5V - Check for input defects : SIF, SCL1/2-IN,SCL1/2-OUT - Check for output defects : SOUND L/R 6-12 Samsung Electronics...
Page 76
It receives RF, AV1/2/3 and S-VHS (Y,C) signals and outputs to Y/Pb/Pr of CXA2180Q, M-OUT and V-OUT through internal switching. - Power supply :1.8V, 3.3V - Check for input defects : RF, SCL1/2,S-VHS(Y,C) - Check for output defects :M-OUT,Y,Pb,Pr,HS1,VS1 Samsung Electronics 6-13...
Page 77
ABL and EHT operation. If V-Drive output is not detected, check for an IC defect. - Power supply : 5V, 9V - Check for input defects : Y/Pb/Pr, H/V - Check for output defects : R/G/B, ABL, EW, V/H-DRIVE 6-14 Samsung Electronics...
Block Diagram 7-2 Partial Block Diagram 7-2-1 Micom Block Diagram 7-2-2 Video Block Diagram R- OU T G- OU T CRT-ASSY B - OU T VG A BLOCK Deflection CXA2165 BLOCK CXA2151 74HC123 BA7657 BA7657 SDA9489 TM BLOCK VSP9402 Samsung Electronics...
Page 81
D V D 1 (D T V ) IN - L D V D 1 (D T V ) IN - R D V D 2 (D T V ) IN - L D V D 2 (D T V ) IN - R 7-2-4 CRT Diagram Samsung Electronics...
Wiring Diagram 8. Wiring Diagram 8-1 Overall Wiring C RT PCB SI G N A L A V - I N SOUND OUT C RT PC B POWER F- BOX I N SERT KEY- CONTROL AC - I N Samsung Electronics...
*GT804 : This is a ground port to prevent high voltage due to lightning and is connected to the Deflection Board. *CN802 : This is a 3 pin port connected to the AC power cable. It is connected to the power cable socket. *GT805, GT806 : This is a port connected to the D-Coil surrounding the CRT. Samsung Electronics...
Page 87
PCB Diagram 9-1-3 Main Board Connector Pin CN401 CN601 Connected to the Deflection Board Connected to the Speaker Port PIN No. Pin Name PIN No. Pin Name V_BLANK EW_OUT H_PULSE VD_P VD_N VCC_20V HDRIVE_OUT VCC_HTD_16V VCC_142V VCC_142V Samsung Electronics...
* CN06 : This is a 4 pin port connected to the Control Ass'y, and receives TV/Video, Menu, Ch Up/Down and Vol -/+ signals. * CN701 : This is a 10 pin port connected to the Side AV, and receives S-Video2 and AV4 external inputs. Samsung Electronics...
Page 89
PIN No. Pin Name PIN No. Pin Name PIN No. Pin Name KEY3 TILT POWER STD-LED KEY1 KEY2 12V-A 12V-B R-OUT G-OUT B-OUT CN701 Connected to the Side AV Port PIN No. Pin Name S-Y2 S-C2 AV4-L AV4-R Samsung Electronics...
* CN401 : This is a 14 pin port connected to the Main Board and is supplied 135V, 16V power by the Main Board and the power on and off signal. * CN403 : This is a 10 pin port connected to the CRT Ass'y, and supplies power for the CRT and R/G/B signal amplifying AMP. Samsung Electronics...
Page 91
9-3-3 Deflection Board Connector Pin CN401 CN403 Connected to the Main Board Connected to the CRT Ass'y PIN No. Pin Name PIN No. Pin Name V_BLANK VCC_200V EW_OUT H_PULSE HEATER VCC_-16.5V VD_P VCC_20V VD_N VCC_20V HDRIVE_OUT VCC_HTD_16V VCC_135V VCC_142V VCC_142V Samsung Electronics...
* CNC02 : This is a port that receives power for the CRT and AMP from the Deflection Board. * FV1 : A port to connect the VM signal to the DY Ass'y. * FN1 : A port to connect signals to the Tilt Coil and is required for the screen slant adjustment. Samsung Electronics...
Page 93
PIN No. Pin Name PIN No. Pin Name VCC-200V HEATER VCC_-16.5V VCC_20V VCC_142V Connects the VM signal to the DY Ass'y Connects the signal to the Tilt Coil PIN No. Pin Name PIN No. Pin Name TILT TILT Samsung Electronics...
Schematic Diagram 10. Schematic Diagram 10-1 MAIN 10-1-1 MAIN 1 This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-1...
Page 95
Schematic Diagram 10-1-2 MAIN 2 This Document can not be used without Samsung’s authorization. Power Signal TP09 TP09 10-2 Samsung Electronics...
Schematic Diagram 10-2 Feature Box 10-2-1 Feature Box 1 This Document can not be used without Samsung’s authorization. Power TP07 Signal TP08 TP07 TP08 Samsung Electronics 10-3...
Page 97
Schematic Diagram 10-2-2 Feature Box 2 This Document can not be used without Samsung’s authorization. Power Signal 10-4 Samsung Electronics...
Page 98
Schematic Diagram 10-2-3 Feature Box 3 This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-5...
Page 99
Schematic Diagram 10-2-4 Feature Box 4 This Document can not be used without Samsung’s authorization. Power Signal 10-6 Samsung Electronics...
Page 100
Schematic Diagram 10-2-5 Feature Box 5 This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-7...
Schematic Diagram 10-3 DEFLECTION This Document can not be used without Samsung’s authorization. TP01 Power Signal TP02 TP01 TP02 TP03 TP03 TP04 TP04 TP05 TP06 TP06 TP05 10-8 Samsung Electronics...
Schematic Diagram 10-7 LED Module 10-8 Master S/W This Document can not be used without Samsung’s authorization. This Document can not be used without Samsung’s authorization. 10-12 Samsung Electronics...
Also used to select items on the on-screen menu. ⑦ POWER Press to turn the TV on and off. ∧ CH ∨ ④ ④ ∨ Press to change channels. Also press to move between items on the on-screen menu. Samsung Electronics 11-1...
Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a DVD player. Because there are three sets of input jacks, you can connect three different A/V components (i.e., a VCR and a DVD, 2 VCRs, etc.) 11-2 Samsung Electronics...
You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, DVD, Cable box, and Samsung Set-top Boxes.
Page 109
SELECTION BY NAME SUB PICTURE(PIP) SIZE SELECTION SUB PICTURE(PIP) LOCATION SELECTION SUB PICTURE(PIP) PREVIOUS CHANNEL FASTEXT TOPIC SELECTION TELETEXT SUB-PAGE PIP ON/OFF TELETEXT STORE TELETEXT SIZE SELECTION INTERCHANGE THE MAIN AND SUB SUB PICTURE(PIP) PICTURE (PIP) SOURCE SELECTION 11-4 Samsung Electronics...
① Remove the 2 screws fixing the Terminal Board and the Board Jacks. : RH, +, B, M4, L15, ZPC(BLK), SWRCH18A 6003-001026 ② Lift the fixing holder up at and pull the Terminal Board to separate it from the unit. Samsung Electronics 12-1...
Page 111
② To separate the power cord, slide the fixing clip and lift the cable up. ① Separate the CRT Ass'y from the CRT ② Separate the TBC wire, GND, VM and Tilt cables from the CRT Ass'y sequentially. 12-2 Samsung Electronics...
Page 112
P u l l t h e w i r e s w h i l e p r e s s i n g o n t h e f i x i n g d i p of the material and the PCB. Samsung Electronics 12-3...
Page 113
Notice: Since pulling the wire by force may damage the coating of the wire, separate the wire holding the metal part with the tool. ① Remove the 4 screws fixing the Deflection Ass'y. : PWH, +, B, M3, L10, ZPC(YEL), SWRCH18A 6003-001023 12-4 Samsung Electronics...
Page 114
Power Board ① Remove the 4 screws to separate the holder fixing the Deflection Board Holder. : RH, +, B, M4, L15, ZPC(BLK), SWRCH18A 6003-001026 ② Separate the holder. ① Separate the cable from the Deflection Board Samsung Electronics 12-5...
- A circuit for correcting the spool shape which appears on the left and right part of a picture. This is caused by the difference between the distances from the center of a picture to each corner. KA393, FQP630 etc. (Adopt PWM circuit) Samsung Electronics 13-1...
- Consists of L304, C305, C439, R312. Symmetrize the up and down amplitude using the saturable reactor of L304 and adjust N/S Gain by controlling the capacity value of C305 and C439 If the correction vector is excessive, one can slightly reduce the resistance of R312 Samsung Electronics 13-3...
Page 119
< Ve r t i c a l W ave fo r m < No r m a l Ve r t ical a f t e r co r r e ct i i o n > S i g na l > 13-4 Samsung Electronics...
Page 120
..D415 : moves to the right of a picture ..D417 : moves to the left of a picture Total Length of a Picture Moved (m/m) Condition Left Center Right To Left To Right To Left To Right To Left To Right After Samsung Electronics 13-5...
Page 121
This is possible by inputting ABL voltage to E/W using R433 as the picture brightness varies. There are H,V, PIN-COMP as well in Factory data and these correct the high voltage regulation. If the H-COMP capacity 13-6 Samsung Electronics...
Page 122
COMP capacity value, therefore, should be varied +/- 1step from the factory- adjusted condition, since a gain widely varies dependant on the SET distribution. ▶Before and After of E/W Circuit Correction Samsung Electronics 13-7...
Ex: For LCD 15:9 devices, "Wide" is displayed on the OSD instead of "16:9". 4. The picture size can be changed even in the blue screen. However, the picture size should be controlled by the product specifications if the change is impossible due to hardware restrictions. Samsung Electronics 14-1...
You can use this AV interface for users by controlling connected AV devices function to study English by watching AFKN or CC marked through the Anynet menu when AV devices of Samsung video tapes. Electronics are connected.