1/12/2014 FILE NO. 060-200325 SERVICE MANUAL Color Television S3ES Chassis 29SZ5DA 29SZ5DE 29SZ5SH 29SZ5ST PRINTED IN MALAYSIA Dec. 2003 (YC/X) Digitized in Heiloo, Holland...
www.freeservicemanuals.info 1/12/2014 SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press o button once on 2) Press o button again to 3) While pressing the o button, Remote Control. keep pressing. press MENU button on TV set. Item Data (Service mode display) 2.
Page 3
www.freeservicemanuals.info 1/12/2014 4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING &...
www.freeservicemanuals.info 1/12/2014 8. SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown. Indicated color of mode now selected : Green and Red Indicated color of other modes : White...
www.freeservicemanuals.info 1/12/2014 DESIGN MODE 1. ENTERING TO DESIGN MODE 2) While pressing (or CALL) button on 3) Press MENU button on TV. 1) Select the Service mode. Remote and press MENU button on TV. ITEM Press DATA Press (Design mode) (Adjustment mode) When QA02 is initialized, items “OPT0”...
www.freeservicemanuals.info 1/12/2014 ELECTRICAL ADJUSTMENTS ITEM ADJUSTMENT PROCEDURE FOCUS VR ADJ 1. Enter the service mode, then select any register item. 2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap- pears on the screen. 3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture screen.
Page 7
www.freeservicemanuals.info 1/12/2014 ITEM ADJUSTMENT PROCEDURE WHITE BALANCE 1. Set Contrast to 40, and brightness to +20 by picture control. ADJUSTMENT 2. Set the TV in service mode, and get the inside W/B adjusting signal with VIDEO button. • CUTOFF ADJUSTMENT 3.
www.freeservicemanuals.info 1/12/2014 CIRCUIT CHECK HIGH VOLTAGE CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below. 1. Connect an accurate high voltage meter to the second anode of the picture tube. 2.
www.freeservicemanuals.info 1/12/2014 CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 29" HIGH VOLTAGE AT ZERO BEAM: 32.8 kV MAX HIGH VOLTAGE: 33.0 kV AC VOLTAGE 110~240 V Table-1 SERVICE MODE ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE: Item Adjustment Reference data...
www.freeservicemanuals.info 1/12/2014 LOCATION OF CONTROLS Front ON-timer indicator (green) z Power indicator (red) Remote sensor a Input source selection z Power switch Behind the door a (3) Video 3 input MENU t c s terminals Channel select Menu item select Headphones jack (ø3.5 mm) –...
www.freeservicemanuals.info 1/12/2014 Remote control Power on/standby CALL index, initial Sound mute TXT/TV selection Direct select (0 _ 9) Input source selection Digit select CH (channel select) Menu item select Volume _ /+ Menu item adjust _ /+ Picture menu MENU Sound menu Teletext function –...
www.freeservicemanuals.info 1/12/2014 PROGRAMMING CHANNEL MEMORY • First, use the ASM (Automatic Search Memory) function to preset all active channels in your area automatically. Then, arrange the preset channels with the SEARCH, SKIP and MFT (Manual Fine Tuning) functions so that you can tune into only desired channels.
Page 13
www.freeservicemanuals.info 1/12/2014 To preset channels (SKIP) To skip a position number After presetting the channels, you may skip unnecessary position numbers so that only the channels you want to watch are selected. Select the position number to skipped with CH s/t buttons or the digit/ direct select (-/--, 0 –...
Page 14
www.freeservicemanuals.info 1/12/2014 • The adjustments below are not necessary under normal conditions. However, in areas of inferior broadcast conditions where adjustment is necessary for a better picture, adjust the tuning with the MFT (Manual Fine Tuning). The AFT OFF status automatically keeps the condition adjusted with the MFT function. •...
· · · · · The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. · · · · · The PC board assembly with mark is no longer available after the end of the production. Model : 29SZ5DA/29SZ5DE/29SZ5SH/29SZ5ST Capacitors ..... CD : Ceramic Disk PF : Plastic Film EL : Electrolytic Resistors ....
Page 16
www.freeservicemanuals.info 1/12/2014 Location Parts No. Descriptiopn Location Parts No. Descriptiopn C444 24503225 PLASTIC FILM CF92 T 1500VH 6200PF H #3 24539183 PLASTIC FILM, 50V 0.020UF J C445 24828563 PLASTIC FILM, 200V 56000PF J #4 24539183 PLASTIC FILM, 50V 0.021UF J C447 24679220 ELECTROLYTIC, 250V 22UF M 3A C667...
Page 17
www.freeservicemanuals.info 1/12/2014 Location Parts No. Descriptiopn Location Parts No. Descriptiopn C815 24092555 CERAMIC DISC, AC250V E 1000PF M CA14 24105680 CERAMIC CHIP, 50V CH 68PF J C816 24766479 ELECTROLYTIC, 50V 4.7UF M CA15 24105680 CERAMIC CHIP, 50V CH 68PF J C817 24092339 CERAMIC DISC, 2KV 330PF K CA48...
Page 18
www.freeservicemanuals.info 1/12/2014 Location Parts No. Descriptiopn Location Parts No. Descriptiopn #4 24794100 ELECTROLYTIC, 16V 10UF M #3 24794100 ELECTROLYTIC, 16V 10UF M CD25 24092743 CERAMIC CHIP, 10V F 0.47UF Z #4 24794100 ELECTROLYTIC, 16V 10UF M CD26 24105560 CERAMIC CHIP, 50V CH 56PF J CS11 #1 24203100 ELECTORLYTIC, 16V 10UF M 7L 3A CD27 24105560 CERAMIC CHIP, 50V CH 56PF J...
Page 19
www.freeservicemanuals.info 1/12/2014 Location Parts No. Descriptiopn Location Parts No. Descriptiopn R232 24011123 CHIP, METAL FILM, 1/20W 12K OHM J R521 24011271 CHIP, METAL FILM, 1/20W 270 OHM J R233 24367273 CARBON FILM, 1/6W 27K OHM G R522 24011271 CHIP, METAL FILM, 1/20W 270 OHM J R303 24321229 OXIDE METAL FILM, 1/2W 2.2 OHM J R544...
Page 20
www.freeservicemanuals.info 1/12/2014 Location Parts No. Descriptiopn Location Parts No. Descriptiopn R819 24310829 OXIDE METAL FILM, 1/2W 8.2 OHM J R4760 24000247 METAL FILM, 1/4W 39K OHM F R821 24366101 CARBON FILM, 1/6W 100 OHM J R4770 24011102 CHIP, METAL FILM, 1/20W 1K OHM J R822 24552103 OXIDE METAL FILM, 1/2W 10K OHM J RA01...
1/12/2014 SCHEMATIC DIAGRAM MODEL : 29SZ5DA/29SZ5DE/29SZ5SH/29SZ5ST WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 34
1/12/2014 SPECIFICATIONS (Representative: 29SZ5DA/DE) Rated voltage ~ 110 V – 240 V, 50/60 Hz Power consumption 126 W (at ~ 220 V, 50 Hz) Dimensions 782 mm × 498 mm × 585 mm (Width × Depth × Height) 46 kg...
Page 35
1/12/2014 TOSHIBA ASIA OCEANIA SERVICE CENTRE TOSHIBA SINGAPORE PTE LTD FILE NO: TAOSC-CTV-20040220-01 echnical DATE : 20 Feb 2004 Product Model 29SZ5 Series (R, MQ, T, SG, TM, DA, AX, SH, ST, TE, ES, DE,) Symptom : Folding at Left side when playing 16:9 bright picture...
Page 36
www.freeservicemanuals.info 1/12/2014 TAOSC Asia Oceania Service Centre Change value of R4704 from chip, metal film:1/16W, 270KΩ to chip, metal film: 1/16W, 360KΩ. Change value of C498 from plastic film: 50V, 1800PF to plastic film: 50V, 3300PF Digitized in Heiloo, Holland...
Page 37
www.freeservicemanuals.info 1/12/2014 SCHEMATIC DIAGRAM MODEL : 21A3E / 21A3TR 21A3M / 21A3MJ WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY NOTE: PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. 1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5% 4.
Page 38
1/12/2014 SCHEMATIC DIAGRAM MODEL : 29SZ5DA/29SZ5DE/29SZ5SH/29SZ5ST WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 39
1/12/2014 4.5V 4.5V 5.0V 32.0V 29SZ5DA/29SZ5DE/29SZ5SH/29SZ5ST MAIN (TUNER) SHEET-1/9 (1/11) Digitized in Heiloo, Holland...