COnTenTS SAFETY WARNINGS SAFETY WARNINGS FOR USE NEEDO RADIATORS INSTALLATION MANUAL USE DIAGNOSTICS CLEANING THE HORIZONTAL MODEL CLEANING THE VERTICAL MODEL USEFUL INFORMATION ETS PARAMETERS DESCRIPTION TECHNICAL DATA CERTIFICATIONS...
WARNINGS The information in this product manual is essential for the correct installation, use and maintenance of the Needo heating system and is up-to-date on the date shown in the actual manual. Any updates or modifications can be found on the www.needo.eu website...
Before using the product, we recommend carefully reading and understanding the following information. Needo products have been designed for you and your needs, but you must remember that they have not been created for uses other than those presented in this manual.
Page 9
Keep away from children This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they benefit by a person responsible for their safety, monitoring or instruction on the use of the appliance.
Page 10
Further safety warnings We recommend that you carefully read the safety warnings in the Installation Guide, provided in the packaging with this manual, to help you fully understand the product. The Manufacturer accepts no responsibility for any improper use, other than the uses indicated, adopted by the purchaser.
T, M, R LINES PRODUCT PRESENTATION The NEEDO design electrical radiator was designed to heat homes and offices and is regulated and controlled through the KNX communication system. The innovative NEEDO technology and the precise heating management control make it...
InSTALLATIOn INSTALLATION GUIDE Installation of the product must only be performed by qualified and skilled personnel. The correct installation procedures are provided in the Installation Guide that is attached to this manual. Once installation is complete it must be kept by the purchaser, together with this manual.
MAnUAL USe Manual radiator control The radiator can be controlled in manual mode thanks to a button placed on the powerbox at the bottom of the radiator itself (Fig. 01). Press this button to choose one of the three operating modes of the radiator. The selection is cyclical: OFF ->...
DIAGnOSTICS The led status (Fig. 02) makes it possible to understand what is happening with your radiator. Below is a brief guide to the various states and the operations to be implemented, if necessary. Fig. 02 LED (Fig. 02) STATUS the temperature in the room is below the set-point Green the temperature in the room is equal to or above the...
CLeAnInG THe HORIZOnTAL MODeL ANTI-DUST SYSTEM The advantages of Needo products Needo products have been designed with you in mind. The possibility of tilting the radiator (Fig. 03), in the case of the horizontal model, allows you to easily clean all the parts of the radiator body, keeping your home healthy.
CLeAnInG THe VeRTICAL MODeL How to clean Before starting to clean the product make sure that the radiator is in stand-by mode and is no longer hot. Clean with a clean dry cloth or with special, non- aggressive products. Fig. 05 What not to do (for both models) Do not clean the radiator when it is switched on.
In the event of modifications, the spare parts are guaranteed for a year. The guarantee is only valid if accompanied by a dated purchase receipt. CONTACTS The Needo Assistance Centre can be contacted as follows: www.needo.eu service@needo.eu DISPOSAL At the end of its lifetime the product must be disposed of in compliance with the current directives of the Country where it is being used.
PARAMeTeRS DeSCRIPTIOn Only for skilled and expert installers COMMUnICATIOn ObjeCTS DeSCRIPTIOn In this Section the KNX Communication Objects available for the NEEDO radiator are described in detail. neeDO – On/Off > Switch – 1.001 - In This “one bit” communication object enables the radiator to be switched between OFF and ON.
Page 19
– Operation mode > Value State – 20.102 - OUT This data point provides the information about the radiator status in terms of Operation Modes. It returns the operation mode as integer from 0 to 5, according to what described for the communication object 3).
Page 20
control the environment temperature according to the value passed by this communication object (as reference), and the setpoint. When this group object is activated, the reference temperature variable sensed by the embedded radiator NTC, (that is commonly used by the system control of the radiator, and is provided by the communication object nr. 13), is ignored by the control algorithm.
Page 21
communication object 8 (External temperature sensor), then the radiator will regulate according to the temperature provided by the value estimated by the NTC. In the other case, if the radiator receives values from communication object 8, then it will regulate according to this value, and the temperature estimated by the embedded NTC is ignored.
Page 22
KNX bus. On change, On request, Cyclically Send integral consumption (default=0, min=0, max=240) 19) User Message - Radiator size > Value State – 14.056 - OUT The RADIATOR SIZE returns the size of the NEEDO radiator in of Watts [W].
Page 23
GeneRIC PARAMeTeRS The following parameters are generic and independent of the communication object adopted in an installation. Operation mode (after power supply error) Default=0, min=0, max=5 Setpoint offset (°C) default=0, min=-5, max=5 Operation mode (after power supply error): The Operation mode (after power supply error) defines the mode on which the radiator has to be recovered after a faulty power supply.
ETSI EN 301 489-17 v2.1.1 (2009) ETSI EN 300 328 v1.7.1 The conformity declaration can be consulted at the following address: www.needo.eu/declaration.php Manual Revision 02/2013 The manufacturer accepts no responsibility for any inaccuracies contained in this document that are due to errors of printing, transcription or translation.