Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Art-Tech MAG-180 SPOT
- Page 1 USER MANUAL...
-
Page 2: Before You Begin
1 x Power cable 1 x User Manual Unpacking Instructions Congratulations on purchasing ART-TECH 180W moving head spot fixture ! Now that you’ve got your moving head spot,you should carefully unpack the carton and check the contents to ensure that all parts are present and in good condition. Notify the... - Page 3 Icons This manual uses the following icons to indicate information that requires special attention on the part of the user. ICONS MEANING This paragraph contains critical installation, configuration or operation information. Failure comply with this information may render the fixture partially or completely inoperative, cause damage to the fixture or cause harm to the user.
- Page 4 ● Secure fixture to fastening device using a safety chain. ● Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher than this. ● In the event of a serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
- Page 5 · Ballast: switching mode power supply Optical System · Beam angle: 14° · Pan: 540°(2.3sec), Tilt: 265° (1.8 sec) · 16-bit resolution · Auto repositioning Color · 7+open, indexable and bidirectional rainbow effect Gobo · Outside ￠25.5mm, inside ￠21.5mm · 6+ open custom interchangeable position for rotating gobo wheel ·...
-
Page 6: Product Dimensions
· Fan speed auto change according to temperature Power · Max power consumption: 250W · Powercon in and out · Power supply: Electronic auto-ranging · Input voltage range: 100–240V, 50-60Hz Dimension and Weight · Fixture:275X245X353MM · Net Weight: 8.3KG · Gross Weight: 9.7KG Rigging ·... -
Page 7: Power Linking
3. SET UP AC Power This fixture runs on 100-240VAC, 50/60 Hz. This fixture used switch power supply, it can transform by itself when user input power. Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0 to 100% switch. -
Page 8: Mounting And Rigging
Mounting & Rigging The Spot may be mounted in any safe position provided there is adequate room for ventilation. Be sure that the structure can support 10 times the weight of the fixture. Please see the “Technical Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. -
Page 9: Configuration (Dmx)
OPERATING Configuration (DMX) Set the product in DMX mode to control with a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. 3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product. - Page 10 White 10-19 White+Red 20-29 30-39 Red+Green 40-49 Green 50-59 Green+Blue 60-69 Blue 70-79 Blue+Yellow 8CH Color 80-89 Yellow 90-99 Yellow+Rose 100-109 Rose 110-119 Rose+Warm White 120-129 Warm White 130-139 Warm White+Cambridge blue 140-149 Cambridge blue 150-180 Cambridge blue+White 181-255 Rainbow Effect(slow to fast) 9CH Focus 000-255 Focus, from near to far...
-
Page 11: Dmx Personalities
DMX Personalities The 180W Moving Head Spot has an 16-channel personality To select DMX personality to use, follow the steps below: 1. Press <MENU> repeatedly until RUN MODE, SETTINGS, SPECIAL on the display 2. Press <UP> or <DOWN> to select RUN MODE 3. -
Page 12: Manual Mode
Manual Mode To enable the Manual mode, do the following. 1. Press <MENU> repeatedly until RUN MODE, SETTINGS, SPECIAL on the display 2. Press <UP> or <DOWN> to select RUN MODE 3. Press<UP> or <DOWN> to select Manual 4. Press<ENTER> INVERT/ PAN To enable the invert/pan mode, do the following. -
Page 15: General Maintenance
5. APPENDIX General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. -
Page 16: General Troubleshooting
General Troubleshooting Symptom Solution Check the fan in the fixture.If it is stopped or moving slower than normal,the unit may Fixture auto shut have shut itself off due to high heat. This is to protect fixture from overheating. Clear the fan of obstruction, or return the unit for service.
Need help?
Do you have a question about the MAG-180 SPOT and is the answer not in the manual?
Questions and answers