Summary of Contents for RHYNO RWC-60
- Page 1 RHYNO 18V 5” Angle Grinder - OPERATOR’S MANUAL - USA Catalog No: RWC-60 TO REDUCE THE RISK OF INJURY, USERS MUST READ AND UNDERSTAND OPERATOR’S MANUAL. Rev A 4/1/2017...
- Page 2 /min ……….. Per minute bpm ………. Beats/min If you have any questions or comments ipm …………. Inches/min about this or any RHYNO tool, call us toll RPM ………… rotations/min free at: sfpm ………. Surface feet/min 844-25RHYNO (844-257-4966) SPM ………..
- Page 3 RHYNO 18V 5" Grinder Tool Tool Tool No Load Wheel Charger AC Input AC Input Battery Battery Battery Catalog Voltage Speed Diameter Catalog Voltage Current Output Catalog Capacity Output 0-8,000 RWC-60 4-5 in. RWC-16 RWC-41...
-
Page 4: General Power Tool Safety
Part Name Qty. Part Name Qty. Housing Button Rotor Pole Switch Stator Dust Protector-Left Switch Dust Protector-Right 1 Gear Box Wheel Guard Screw (T15) Inner Flange Outer Flange Pinion Gear Lock Nut Wrench Ball Bearing Screw (T10) Gear Box Cover © Charger Side Handle Battery Pack... -
Page 5: Personal Safety
protected supply. Use of a GFCI reduces a. Do not force the power tool. Use the the risk of electric shock. correct power tool for your application. 3) PERSONAL SAFETY The correct power tool will do the job a) Stay alert, watch what you are doing better and safer at the rate for which it common sense... - Page 6 b) Operations such as polishing are not charger that is suitable for one type of battery pack may create a risk of fire recommended to be performed with when used with another battery pack. this power tool. Operations for which b) Use power tools only with specifically the power this power tool was not designated battery packs.
- Page 7 n) Regularly clean the power tool’s air accessories will normally break apart during this test time. vents. The motor’s fan will draw the h) Wear personal protective equipment. dust inside the housing and excessive Depending on application, use face accumulation of powdered metal may shield, safety goggles or safety glasses.
-
Page 8: Kickback And Related Warnings
w) Always handle and store wheels in a start up. The operator can control careful manner. torque reaction or kickback forces if x) Do not operate this tool for long periods proper precautions are taken. of time. Vibration caused by the b) Never place you hand near the rotating operating action of this tool may cause accessory. -
Page 9: Additional Safety Warnings Specific For Abrasive Cutting-Off Operations
attempt to remove the cut-off wheel wheel and sparks that could ignite clothing. from the cut while the wheel is in d) Wheels must be used only for motion otherwise kickback may occur. recommended applications. Investigate and take corrective action to example: do not grind with the side of eliminate the cause of wheel binding. -
Page 10: Additional Safety Information
operation. Do not overstress the wires • Arsenic and chromium from chemically- by applying excessive load to the treated lumber. brush. The wire bristles can easily Your risk from these exposures varies, penetrate light clothing and/or skin. depending on how often you do this type b) If the use of a guard is recommended of work. -
Page 11: Important Safety Instructions For All Battery Packs
• Do not incinerate the batter pack even catalog number and voltage. Your tool if it is severely damaged or is uses a RHYNO charger. Be sure to read all completely worn out. The battery pack safety instructions before using your can explode in a fire. -
Page 12: Important Safety Instructions For All Battery Chargers
Fuel Gage Battery Packs temperature and end-user application. RHYNO Battery Packs or tools include a fuel Important Safety Instructions for gage which consists of three green LED All Battery Chargers lights that indicate the level of charge remaining in the battery pack. - Page 13 CAUTION: Burn hazard. To reduce the risk injury, charge only RHYNO 12 Not recommended rechargeable battery packs. Other types of battery packs may overheat and burst • Do not place any object on top of the resulting in personal injury and property charger or place the charger on a soft damage.
-
Page 14: Charging A Battery Pack
(0°-45°C) the LED will indicate RED & b. Remove the battery pack from the tool GREEN. for charging when needed. RHYNO e. A fully discharged battery pack with an Lithium-ion battery packs do not internal temperature in the normal develop “memory” when charged after range will charge in about 15-20 only a partial discharge. -
Page 15: Assembly And Adjustments
flammable or combustible solvents around Before using the tool, check that the batteries, charger or tools. handle is tightened securely. 4) REPAIRS The charger has no serviceable parts. Hot/Cold Battery Pack Delay When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the batty pack has reached an appropriate temperature. - Page 16 (3.17m), the tool must be serviced and rea- always placed between the spindle and the assembled by a RHYNO service center. operator. Failure to have the tool serviced may cause Tighten guard screw securely.
- Page 17 guard can result in injury due to wheel not required for these accessories, the breakage and wheel contact. See the guard may or may not fit correctly. Accessories Chart for more information. WARNING: Failure to properly seat 1) Install the unthreaded inner flange on the flange/clamp/nut wheel could result in spindle with the raised section (pilot) serious injury (or damage to the tool or...
-
Page 18: Operation
1) Thread the wheel on the spindle by WARNING: Failure to properly seat hand. the flange/ clamp nut/ wheel could result 2) Depress spindle lock button and use a in serious injury (or damage to the tool or wrench on the hub of the wire wheel or wheel). -
Page 19: Proper Hand Position
Proper Hand Position WARNING: Allow the tool to reach full speed before touching tool to the work WARNING: To reduce the risk of surface. Lift the tool from the work surface serious personal injury, ALWAYS use before turning the tool off. proper hand position as shown. -
Page 20: Personal Safety
Surface Grinding, Sanding and Wire motion to avoid creating gouges in the work surface. Brushing b. If sanding with a backing pad, move the tool constantly in a straight line to CAUTION: Always use the correct prevent burning and swirling of guard per the instructions in this manual. -
Page 21: Environmental Safety
or whenever the wearer has difficulty women should be kept away from the breathing. immediate work area. 3. All toys, washable furniture and utensils used by NOTE: Only those dust masks suitable for children should be washed thoroughly working with lead paint dust and fumes before being used again. -
Page 22: Maintenance
WARNING: Never use solvents or with this tool could be hazardous. To other harsh chemicals for cleaning the reduce the risk of injury, only RHYNO and non-metallic parts of the tool. These We Cut The Glass, LLC recommended chemicals may weaken the plastic... -
Page 23: Register Online
RHYNO factory service way. RHYNO and We Cut The Glass, LLC center or a RHYNO authorized service are not responsible for any injury caused center. -
Page 24: Limited Warranty
(2) years after the date of purchase unless otherwise noted. Return of the tool to a RHYNO factory service center location, freight prepaid and insured, is required. A copy of the proof of purchase should be included with the return product.
Need help?
Do you have a question about the RWC-60 and is the answer not in the manual?
Questions and answers