® Operating Instructions Pallmann King Cobra Sanding Machine ® PALLMANN | 14509 E. 33rd Place, Unit G | Aurora CO 80011 | 720.374.4810 | Fax 720.374.2113 | www.pallmann.us...
Page 2
Reproduction in whole or in part requires written permission from Switching off and storing the machine ..........................Pallmann USA, Aurora CO. Toll free 866-505-4810. Declaration of conformity .............................. No liability for any damage arising from the use of this manual.
Adjusting the tension roller ............................... 8.4 Adjusting the tension roller ..................24 Changing the belt................................8.5 Replacing the belt ......................26 Checking dust extraction ..............................8.6 Checking dust extraction .....................27 Switching off and storing the machine ..........................8.7 Switching off and storing the machine ..............27 Declaration of conformity .............................. Warranty .........................28 Warranty................................... Pallmann King Cobra Manual...
Before starting to work, make yourself familiar with the operation of the machine. It’s too late if you do it while working! Never allow anyone without sufficient skills and knowledge operate the machine. Pallmann King Cobra Manual...
Changing the sanding drum ............................Adjusting the running wheels ............................Adjusting the castor wheels ............................Adjusting the tension roller ............................... Changing the belt................................Checking dust extraction ..............................Switching off and storing the machine ..........................Declaration of conformity .............................. Warranty................................... Pallmann King Cobra Manual...
The King Cobra wood floor sander is suitable for dry sanding of wood floors. No other use is recommended. Caution! fatal Never use King Cobra for wet procedures. There is a fatal risk from electric shock! fatal Pallmann King Cobra Manual...
Contents 5.1 Installing the dust tube Introduction ..................................Note: The King Cobra is delivered with the dust tube (1) removed. Scope of delivery ................................Caution! Machine specifications COBRA CLASSIC ........................Injury to the operator or other persons could occur or damage could occur if the fatal machine starts up unintentionally.
3. Loosen both of the wing screws a little (4). Push the handle down to detach the control rod (5) from the connector (8). 4. Open the guide tube support (7) with the clamping lever (6) and pull the guide tube (1) out. Pallmann King Cobra Manual...
Adjusting the tension roller ............................... Changing the belt................................Checking dust extraction ..............................6. Now you can remove the Switching off and storing the machine ..........................motor. Declaration of conformity .............................. Warranty................................... COBRA CLASSIC #74540 09/2014 Pallmann King Cobra Manual...
Caution! Wear safety goggles! Changing the belt................................Checking dust extraction ..............................When using the King Cobra floor sander and when working on the King Cobra sanding fatal Switching off and storing the machine ..........................machine always wear safety goggles to protect your eyes.
When using the parquet floor sander COBRA CLASSIC and when working on COBRA fatal Use only original Pallmann® dust bags for the King Cobra floor sander. The dust bag CLASSIC, never wear loose clothing. This can get caught up in moving parts.
Switching off and storing the machine ..........................5. Insert a new sanding belt. Declaration of conformity .............................. 6. Clamp the new sanding belt by moving the tension lever (2) backward. Warranty................................... 7. Close the sanding drum cover (1). Pallmann King Cobra Manual...
Declaration of conformity .............................. Caution! Fatal risk from electric shock! Running over the electric cable with the sander entails a fatal risk from electric shock! fatal Warranty................................... Never point the machine towards the cable! Pallmann King Cobra Manual...
Risk of injuries from the machine starting up unintentionally! Disconnect the machine Warranty................................... fatal from the power supply when not in use, when changing the sanding belt, and when carrying out any other work to the machine. Pallmann King Cobra Manual...
4. Set the switch to setting "I". Once the motor has started up, switch to setting "II". This “Run”. This gradual start-up procedure avoids high current to enter the motor gradual start-up procedure avoids high start-up currents. during start up. Pallmann King Cobra Manual...
Page 17
Declaration of conformity .............................. always be held up because otherwise the sanding drum will be lowered to the flo Caution! Warranty................................... To avoid creating uneven sanding marks in floor, always walk at an even pace fatal while sanding. Pallmann King Cobra Manual...
Page 18
Pallmann King Cobra Manual machine is moving evenly again.
Safeguard the machine to prevent it rolling away. The sanding dust contained in the dust bag must be disposed of immediately in a The sanding dust contained in the dust bag must be disposed of immedia Warranty................................... fire proof, non-flammable container. The container must be covered with a fire proof, fire-proof, non-flammable container. The container must be covered with a fir non-flammable lid. Store the container only outdoors. non-flammable lid. Store the container only outdoors. Pallmann King Cobra Manual...
4. Fold the tension lever (2) forward to relieve the tension on the sanding belt. will not fall off while the King Cobra is in operation. To unscrew the retaining nut, use the double fork wrench that comes with the machine. Lower the sanding drum so Warranty...................................
Page 21
Warranty................................... After chanding the sanding drum, the surface setting on the machine must be readjusted (See chapter 8.2). Note! Pallmann King Cobra Manual After changing the sanding drum, the surface setting on the machine must be ne (See chapter 8.2)
Switching off and storing the machine ..........................the right running wheel. Declaration of conformity .............................. Warranty................................... 5. Loosen the cam fixation screw on the running wheel brac 5. Loosen the cam fixation screw on the running wheel b Pallmann King Cobra Manual...
Page 23
Switching off and storing the machine ..........................2. Adjusting required Declaration of conformity .............................. Correct 3. Optimal sanding pattern Warranty................................... Adjusting the castor wheels Instructions for adjusting the casto Adjusting the castor wheels Pallmann King Cobra Manual Instructions for adjusting the castor whe...
Changing the sanding drum ............................Adjusting the running wheels ............................Adjusting the castor wheels ............................Adjusting the tension roller ............................... Changing the belt................................Checking dust extraction ..............................Switching off and storing the machine ..........................Declaration of conformity .............................. Warranty................................... Pallmann King Cobra Manual...
Page 25
Adjusting the running wheels ............................Adjusting the castor wheels ............................Adjusting the tension roller ............................... Changing the belt................................Checking dust extraction ..............................Switching off and storing the machine ..........................Declaration of conformity .............................. Warranty................................... Pallmann King Cobra Manual 5. Loosen the retaining nut (1).
3. Slightly lift the belt tensioner ( 2 ) and pull back the locking stud ( 3 ). 4. Lower the belt tensioner to take up belt slack. 4. Lower the belt tensioner to take up belt slack. Pallmann King Cobra Manual...
Changing the sanding drum ............................Adjusting the running wheels ............................Adjusting the castor wheels ............................Adjusting the tension roller ............................... Changing the belt................................Checking dust extraction ..............................Switching off and storing the machine ..........................Declaration of conformity .............................. Warranty................................... Pallmann King Cobra Manual...
Warranty Contents The warranty period for new Pallmann® machines shall last for one year from the point at which the machine is transferred / delivered to the customer, insofar as statutory legal requirements do not stipulate otherwise. Introduction ..................................When validating warranty claims, the invoice or proof of purchase must always be submitted.