Advertisement
Quick Links
Download this manual
See also:
User Manual
NetScreen-5GT
*HWWLQJ 6WDUWHG
8VH WKH LQVWUXFWLRQV LQ WKLV *HWWLQJ 6WDUWHG JXLGH WR KHOS \RX FRQQHFW DQG FRQILJXUH \RXU
1HW6FUHHQ*7 )RU PRUH FRQILJXUDWLRQ H[DPSOHV DQG GHWDLOV VHH WKH 1HW6FUHHQ*7 8VHU·V *XLGH
DQG WKH 1HW6FUHHQ &RQFHSWV
Router
&211(&7,1* 7+( '(9,&(
8VLQJ WKH LQVWUXFWLRQV EHORZ FRQQHFW WKH 1HW6FUHHQ*7 DQG SUHSDUH WR FRQILJXUH WKH
GHYLFH WR SURWHFW \RXU QHWZRUN 8VH WKH /('V RQ WKH IURQW SDQHO RI WKH GHYLFH WR KHOS
\RX GHWHUPLQH WKH GHYLFH VWDWXV
6WHS
Connect an Ethernet cable from the Untrusted port of the
NetScreen-5GT to the external router, cable modem, or DSL modem.
6WHS
•
If the workstation is in a LAN (see diagram), connect a cable
from the Trusted port to the internal switch or hub.
•
If the workstation is a single workstation, connect an Ethernet
cable from the Trusted port directly to the Ethernet port on
the workstation.
6WHS
Connect the power cable between the NetScreen-5GT and a power
source. NetScreen recommends using a surge protector.
a.
Ensure that the Power LED glows green. This indicates the
device is receiving power.
b.
After the device starts (should take about 30 seconds), ensure
that the Status LED blinks green. This indicates the device is
operating normally.
([DPSOHV 6FUHHQ26 5HIHUHQFH *XLGH
Internet
1
3
Hub/Switch
LAN
2
The numbers on the diagram are paired with the
c.
Ensure that the Link Activity LEDs glow green for the connected
interfaces. This indicates the device has network connectivity.
6WHS
Configure the workstation to access the NetScreen-5GT via a
Web browser:
a.
Ensure that your workstation is properly connected to your LAN
(use the diagram above).
b.
Change the TCP/IP settings of your workstation to obtain its IP
address automatically from the NetScreen-5GT via DHCP. For
help, see the operating system documentation for your
workstation.
Note: Ensure that your internal network does not already have a
DHCP server.
c.
If necessary, restart your workstation to enable the changes to
take effect.
*HWWLQJ 6WDUWHG *XLGH
3a
3b
3c
steps below
Advertisement
Related Manuals for NetScreen Technologies 5GT
Summary of Contents for NetScreen Technologies 5GT
- Page 1 This indicates the device has network connectivity. Connect an Ethernet cable from the Untrusted port of the 6WHS NetScreen-5GT to the external router, cable modem, or DSL modem. 6WHS Configure the workstation to access the NetScreen-5GT via a Web browser: •...
- Page 2 Yes option, select the Load Configlet from: option, browse to the file location, then click Next. The configlet sets up the NetScreen-5GT for you. If you use a configlet, you can skip the remaining instructions in this guide.
- Page 3 • Select Static IP to assign a unique and fixed IP address to the Check the Enable NAT check box if you want the NetScreen-5GT to Untrust zone interface. Enter the Untrust Zone Interface IP be in Route mode with NAT enabled. Click Next.
- Page 4 All rights reserved. NetScreen, NetScreen Technologies, GigaScreen, NetScreen-Security Manager, NetScreen-Remote, NetScreen ScreenOS and the NetScreen logo are trademarks and registered trademarks of NetScreen Technologies, Inc. in the United States and other countries. All other trademarks and registered trademarks are the property of their respective IÃ("(&&ÃSr‰Ã7...
Need help?
Do you have a question about the 5GT and is the answer not in the manual?
Questions and answers