1. Manuals
  2. Brands
  3. Opale Parachutes Manuals
  4. Accessories
  5. SAFETECH ST60-X
  6. User manual

Opale Parachutes SAFETECH ST60-X User Manual

Parachute rescue kit
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents

2016
User's manual
v1.0
SAFETECH 4.9K
ST60-X
Please read this manual before first use.
O p a l e - P a r a c h u t e s . c o m
Opale Aero System SARL - 23 rue de la Motte
62250 MARQUISE - France
contact@opale-aerosystem.com +33(0)981 144 387
© Copyright 2016 - Opale Aerosystem SARL - Tous droits réservés

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SAFETECH ST60-X and is the answer not in the manual?

Questions and answers

Summary of Contents for Opale Parachutes SAFETECH ST60-X

  • Page 1 2016 User’s manual v1.0 SAFETECH 4.9K ST60-X Please read this manual before first use. O p a l e - P a r a c h u t e s . c o m Opale Aero System SARL - 23 rue de la Motte 62250 MARQUISE - France contact@opale-aerosystem.com +33(0)981 144 387 ©...

  • Page 2: Composition Of The Kit

    Thank you for choosing Opale-Parachutes. Composition of the kit This user’s guide includes all the information you need to assemble and use your parachute rescue kit. A good knowledge of your equipment will allow you to safely obtain most of its performances .Thanks for giving this manual to the new owner in case you decided to sell your kit.
  • Page 3 Falling speed / impact energy characteristics according to the drone mass ( approximate value ): Assembling Masse Totale (kg) (lb) 10.8 Install 2 CHC M3x12 screws with M3 nuts. Falling speed (m/s) Impact energy (J) Place the servomotor. The sprocket has to be on the left side, as shown on the picture.
  • Page 4 Assembling Assembling Attach the line provided to the tube base by passing Pass the line through the piston. the line through the loop. Take out the other end of the line on the opposit side. Prepare 1 CHC M3x8 with a large M3 washer. Arrange the line loop on the screw, as shown on the picture.
  • Page 5 Assembling Assembling The arming rod has to stand out at the base of the Do the same operation symetrically in relation to the tube.. first piece of adhesive foam. Lock the arming rod with the “Remove Before Flight” pin. Parachute preparation and installation Remove the parachute from its pocket and unfold it totally.
  • Page 6 Parachute preparation and installation Parachute preparation and installation Again divide equally the panels to the left and to the Arrange the parachute inside the tube, and make right. sure that the lines and the parachute trailing edge With the first half, do a simple S. And hold those pan- are placed upwards the tube.
  • Page 7 Parachute preparation and installation Parachute preparation and installation Slide the 8 on top of the parachute. In locking status the piston is locked with the pin. The servomotor horn can have an angle from 45 to 70° (the angle formed by the servomotor plan and the horn).
  • Page 8 Installation on the DJI Inspire 1 Installation on the DJI Inspire 1 Composition of the ST60-X adapter kit for the DJI Fix the tube on the socket with 3x CHC M3-8 screws Inspire 1 (ref OP17602) and 3x M3 nuts. Composed of carbon fiber parts and hardware kit.

  • Page 9: Maintenance

    These operations can be done at our workshop. Please contact your Opale Parachutes team. O p a l e - P a r a c h u t e s . c o m O p a l e - P a r a c h u t e s . c o m...

Table of Contents