Subscribe to Our Youtube Channel
Related Manuals for Compex WPJ344
Summary of Contents for Compex WPJ344
- Page 1 WPJ344 Hardware Manual...
- Page 2 Please direct any comments or suggestions about this document to: feedback@compex.com.sg Trademark Information Compex® is a registered trademark of Compex Systems Pte Ltd. Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp. All other brand and product names are trademarks or registered trademarks of their respective owners.
-
Page 3: Table Of Contents
Contents COPYRIGHT ..............................2 REVISION HISTORY ............................ 2 DEVELOPMENT KITS ..........................2 BLOCK DIAGRAM ............................2 KEY FEATURES ............................3 General Information ............................ 3 Information on Power ..........................3 CONFIGURATION AND INSTALLATION ....................4 GPIO Bit Mapping ............................4 Interface Connectors ............................ 4 Serial Port Header ............................ -
Page 4: Copyright
REVISION HISTORY Revision Information / Changes Rev 1.0.0 First release for WPJ344 BareBoard Rev 1.0.1 Update to 6A06 Version Rev 1.0.2 Make some layout changes. DEVELOPMENT KITS The Development Kits consist of JTAG and Serial Converter. Please contact our sales team at sales@compex.com.sg... -
Page 5: Key Features
(LV) 9V~24V DC Supported Voltages ：3.3V and 5V MINIPCIE SLOTS Supports all Compex WLE Series Depend on Order Configuration. JTAG Programmer available to reprogram the flash in case of loader corruption. Serial Converter available to change the TTL signals on board to RS232 signals for debugging. -
Page 6: Configuration And Installation
The connectors are listed in the section below and the connector locations are shown in the following diagrams. Connector Function Connector Function Power J12/J13 Ethernet Ports USB signal JTAG Port Mini-PCIE Slot 3.3V Serial Port Power Jack Reset Button WPJ344 Hardware Manual... -
Page 7: Serial Port Header
Please attach the serial converter first on the board serial header, before attaching the power supply. This is to ensure that there is no surge of power to the serial converter, and prevent any damage the chipset on the serial converter. WPJ344 Hardware Manual... -
Page 8: Serial Converter Pin Layouts
RX – Yellow Pin 4 RX – Yellow Pin 3 TX – Orange Pin 6 GND – Green Pin 7 GND – Green Arrangement of Cables on Arrangement of Cables on the Serial Converter to the board board itself WPJ344 Hardware Manual... -
Page 9: Jtag Port Header
Ethernet Connectors The board contains 2 X 10/100/1000 Base-T Ethernet Channels. The Ethernet Channels are available through standard 8-pin RJ45 connectors. Ethernet Connectors(P1/P2) signals is shown below. SIGNAL SIGNAL TX+/POE+ TX-/POE+ TX-/POE+ RX-/POE- RX+/POE- RX+/POE- TX+/POE+ RX-/POE- WPJ344 Hardware Manual... -
Page 10: Jtag Process
JTAG PROCESS Minimum Requirement 1. OCD Commander Ver2.5.4 2. upbios.tst file (same for all Compex device) 3. uboot.bin file 4. JTAG cable Steps 1. Install the OCD Commander to your PC 2. Plug the JTAG cable to the JTAG port of the device 3. -
Page 11: Firmware
“packages” from the OpenWRT into CompexWRT easily with the SDK provided. CompexWRT Firmware: Please download from www.compex.com.sg CompexWRT Firmware (with no Compex Logo): Please contact the sales person in charge for your account. CompexWRT Usermanual: Please download from www.compex.com.sg CompexWRT SDK: Please contact the sales person in charge for your account. -
Page 12: Appendixi
①After connecting this two pin with Jumper, the board can provide on- board 5V to the radio card. 5V Pin ②Plug 5V cable to the 5V pin, the cable can provide external 5V power. Refer to RMF. WPJ344 Hardware Manual... - Page 13 JTAG port JTAG jumper header for programming mini-PCIE slot 9.2mm height mini-PCIE slot Radio 2.4GHz On-board radio(23dBm/perchain) USB Pin Support USB Port and USB Extension AR9344 Main Chipset Serial port Serial port connection header WPJ344 Hardware Manual...
-
Page 14: Faq
1. The Ethernet ports are two LAN port in default，WAN port is defined by software，so you can change any Ethernet port to WAN port in Luci interface. WPJ344 Hardware Manual...
Need help?
Do you have a question about the WPJ344 and is the answer not in the manual?
Questions and answers