Summary of Contents for Genie H2O 3500
- Page 1 ASSEMBLY AND OPERATION MANUAL For Use With GreaseShield Units Pressurized flow through water heater Genie H2O 3500, 4000, 4500, 5000, 5500...
- Page 2 Advantages of pressurized flow through water heaters “Genie H20” Instant water heaters Genie H2O 3500, 4000, 4500, 5000, 5500 series are pressure heaters of power adequately 3.5, 4.0, 4.5, 5.0 and 5.5 kW prepared for 230V power supply. They are designed for supplying hot water for such receivers as wash basins, sinks, showers (using original manufacturer’s sprayer set).
-
Page 3: Safety Regulations
Table 2. Heater power depending on voltage in electric system Voltage Genie H20 3500 3500 3200 2917 2646 2390 Genie H20 4000 4000 3640 3320 3024 2720 Genie H20 4500 4500 4095 3735 3400 3060 Genie H20 5000 5000 4550... -
Page 4: Wiring System
Before heater’s installation check state of wiring system and particularly terminal. After heater’s connection to wiring system measure voltage drop under load Fig.2 Genie Genie Genie Genie Genie Type 3500 4000 4500 5000 5500 Minimum wire cross section [mm²] Current intensity [A] 15.2 17.4 19.6 21.7... - Page 5 4. Assembly CAUTION! The device can only work in position showed on drawing No 1. Heater installation in position other than proper one or without water filter can damage heating element and cause the guarantee to be null and void. Do not screw connecting hoses with high power in order to avoid threads damage.
-
Page 6: Operating Principal
5. Operating Principal In addition to the NORMAL inlet, The GS-LL incorporates a Low level tank to which the outlet from a 20 grid floor level oven is connected. The low level tank includes a bypass outlet to the normal drain as a backup overflow system should the GS-LL malfunction. The tank also includes a final baffle so that should bypass occur grease will not be pas- sed to drain. - Page 7 7. Switch on the HOD unit at the main socket. 8. Undo the access cover on the GS and press and hold button “B” for 10 seconds. This will open the water solenoid for 5 minutes and allow water to enter the LL tank. This in course will then be pumped up to the main tank .Repeat as necessary to fill the Main Tank of the GS.
-
Page 8: Water Filter Cleaning
Fig. 3 Fig. 4 8. Water filter cleaning 1. Turn off water inflow by shutting off valve and disconnect from power line. 2. Disconnect hose from heater intake. 3. Take out filter (using small screw driver – see fig. 8). 4. -
Page 9: Defects And Repair
5. Install filter into heater intake with basket bottom down (Fig. 9) 6. Connect hose to the heater. 7. Open water valve and check tightness. 8. Before power switching on check electronic system is not splashed with water – if so, blow up with air to remove water from electronic circuit board. - Page 10 Water temperature on heater exit too high water flow suppressed too much by control valve (adjust water flow according to – chapter 6) – blocked water filter (clean it out according to chapter 7) – water pressure in water system too low Heater is switching on and out automatically water pressure oscillation in water system –...
-
Page 11: Technical Data
10. Technical data Perfect Perfect Perfect Perfect Perfect Type 3500 4000 4500 5000 5500 Power [kW] 15.2 17.4 19.6 21.7 23.9 Current intensity[A] Voltage [V] Minimum switching water 1.25 flow [l/min] Maximum water pressure 0.65 0.65 0.65 0.65 0.65 [MPa]... - Page 12 Environmental Products and Services Ltd 5 Shepherds Drive | Carnbane Industrial Estate | Newry | Co. Down | BT35 6PH | Northern Ireland Tel: +44 (0) 28 3083 3081 Fax: +44 (0) 28 3025 7556 Email: GenieHoD@EPAS-Ltd.com Web: EPAS-Ltd.com...
Need help?
Do you have a question about the 3500 and is the answer not in the manual?
Questions and answers