Subscribe to Our Youtube Channel
Summary of Contents for SMA Solar Technology BTREP-OUT.GR1
- Page 1 ® Device for Closing Dead Zones with SMA Bluetooth Wireless Technology SMA BLUETOOTH REPEATER OUTDOOR Installation Manual BTREPOUT-IA-en-11 | 98-0054411 | Version 1.1...
-
Page 3: Table Of Contents
SMA Solar Technology AG Table of Contents Table of Contents 1 Information on this Document......5 2 Safety . - Page 4 Table of Contents SMA Solar Technology AG 10 Troubleshooting ........27 10.1 Voltage Supply .
-
Page 5: Information On This Document
SMA Solar Technology AG 1 Information on this Document 1 Information on this Document Validity This document is valid for the following device types as of hardware version A1 and firmware version V 1.07.R: • BTREP-OUT.GR1 • BTREP-OUT.GR2 Target Group This document is for skilled persons. - Page 6 1 Information on this Document SMA Solar Technology AG Typographies Typography Usage Example bold • Display messages • The value can be read from the Energy field. • Elements of a user interface • Select Settings. • Connections • Enter the value 10 in the •...
-
Page 7: Safety
Only use the SMA Bluetooth Repeater Outdoor in accordance with the information provided in the enclosed documentation. Any other use may result in personal injury or property damage. Supported Products The SMA Bluetooth Repeater Outdoor may only be used with the following SMA Solar Technology AG products: • All SMA communication products with Bluetooth •... -
Page 8: Qualification Of Skilled Persons
2 Safety SMA Solar Technology AG 2.2 Qualification of Skilled Persons The work described in this document must be performed by skilled persons only. Skilled persons must have the following qualifications: • Training in the installation and commissioning of electrical devices and plants •... -
Page 9: Scope Of Delivery
Figure 1: Components included in the scope of delivery with order option top-hat rail power supply unit Item Quantity Description Bluetooth Repeater Outdoor (device type „BTREP-OUT.GR1“), pre-assembled Screw Wall plug Installation Manual... -
Page 10: Order Option Power Module
3 Scope of Delivery SMA Solar Technology AG 3.2 Order Option Power Module Check the scope of delivery for completeness and any externally visible damage. Contact your specialist dealer if the scope of delivery is incomplete or damaged. Figure 2: Components included in the scope of delivery with order option Power Module... -
Page 11: Product Description
Use of the Bluetooth Repeater Outdoor (example) Figure 3: The Bluetooth Repeater is used in outdoor installations to close dead zones under unfavourable installation conditions between SMA Solar Technology AG devices with Bluetooth or to improve poor wireless connections. Item Description... -
Page 12: Device Overview
4 Product Description SMA Solar Technology AG 4.3 Device Overview Figure 4: Overview of the enclosure elements (with enclosure lid (left-hand) and enclosure bottom (right-hand)) Item Description Seal Enclosure lid screw Top-hat rail power supply unit* Feed-through terminal for the connection to the voltage supply... - Page 13 SMA Solar Technology AG 4 Product Description Overview of the device elements on the Bluetooth Repeater Outdoor Figure 5: Item Description Colour Explanation − − Terminal DC source (top-hat rail power supply unit or Power Modul) Green LED for voltage supply MODE −...
- Page 14 4 Product Description SMA Solar Technology AG Figure 7: Overview of the terminals on the feed-through terminal Item Description Terminal 1 for the connection of the voltage supply cable Terminal 2 for the connection of the voltage supply cable BTREPOUT-IA-en-11 Installation Manual...
-
Page 15: Assembly
SMA Solar Technology AG 5 Assembly 5 Assembly 5.1 Selecting the Mounting Location Requirements for the mounting location: ☐ If the top-hat rail power supply is used, the mounting location must be in the vicinity of a socket-outlet in the interior area. - Page 16 5 Assembly SMA Solar Technology AG Determining the Mounting Location Determine the mounting location by varying the distance between the Bluetooth Repeater Outdoor and devices with a critical connection signal until all devices display at least a "good" signal. Requirements: ☐...
- Page 17 SMA Solar Technology AG 5 Assembly 6. Check that the connection quality for all devices is at least "good". During this procedure, all devices must be in their usual positions (e.g., the Sunny Beam with Bluetooth must not be held...
-
Page 18: Mounting The Bluetooth Repeater Outdoor On The Wall
5 Assembly SMA Solar Technology AG 5.2 Mounting the Bluetooth Repeater Outdoor on the Wall Requirement: ☐ Bluetooth Repeater Outdoor must be disconnected. 1. Loosen the screws of the enclosure lid and remove the lid. 2. Drill holes through the indentation in the enclosure edges. -
Page 19: Electrical Connection
Danger to life due to electric shock in the event of mixing up the Bluetooth Repeater Outdoor Only the Bluetooth Repeater Outdoor of the device type „BTREP-OUT.GR1“ is allowed to be connected via the top-hat rail power supply unit to the alternating current grid. - Page 20 6 Electrical Connection SMA Solar Technology AG 1. Loosen the screws of the enclosure lid and remove the lid. 2. Unscrew the nut from the lower left corner of the cable gland and push out the filler-plug. 3. Preparing the cable: –...
-
Page 21: Connecting The Bluetooth Repeater Outdoor To The Voltage Supply
SMA Solar Technology AG 6 Electrical Connection 9. Check whether the cable gland seal is correctly in place. The seal must not protrude over the cable gland. 10. Hand-tighten the nut to the cable gland. Tighten the nut with a torque of 0.8 Nm thus securing the cable. - Page 22 6 Electrical Connection SMA Solar Technology AG 4. Insert the cable into the enclosure through the nut and the cable gland. 5. Connecting the cable to the feed-through terminal in the inside of the enclosure: – Push the terminal 1 and terminal 2 of the feed-through terminal open using a screwdriver (2.5 mm).
-
Page 23: Settings
SMA Solar Technology AG 7 Settings 7 Settings 7.1 Setting the MODE The MODE rotary switch is set to the position 0 for delivery. Other positions are not permitted and are intended for SMA Service only. • If the MODE rotary switch is not positioned correctly, set the correct position: –... - Page 24 7 Settings SMA Solar Technology AG NetID 1 is possible for plants with 1 inverter You may leave the default NetID set to 1 in your inverter if your Bluetooth plant consists of the following products: • A maximum of one inverter •...
-
Page 25: Maintenance And Care
SMA Solar Technology AG 8 Maintenance and Care 8 Maintenance and Care • Check the Bluetooth Repeater Outdoor regularly for external damage or soiling. • If external damage to the Bluetooth Repeater Outdoor is severe enough to impair correct function, replace the Bluetooth Repeater Outdoor. -
Page 26: Decommissioning
• Dispose of the Bluetooth Repeater Outdoor in accordance with the locally applicable disposal regulations for electronic waste. Send the Bluetooth Repeater Outdoor back to SMA Solar Technology AG with shipping paid by sender. When doing so, label the packaging "ZUR ENTSORGUNG" ("FOR DISPOSAL"). -
Page 27: Troubleshooting
SMA Solar Technology AG 10 Troubleshooting 10 Troubleshooting 10.1 Voltage Supply 10.1.1 LED RDY The LED RDY is only visible when the enclosure lid is open. • In order to open the enclosure lid loosen the four enclosure lid screws. - Page 28 10 Troubleshooting SMA Solar Technology AG Status Meaning Measure No power supply or the power If you are using the top-hat rail power supply is too low. supply unit: The Bluetooth Repeater Check whether the socket-outlet is supplying Outdoor is not in operation.
-
Page 29: Leds Of The Top-Hat Rail Power Supply Unit
SMA Solar Technology AG 10 Troubleshooting 10.1.2 LEDs of the Top-Hat Rail Power Supply Unit The LEDs of the top-hat rail power supply unit are only visible when the enclosure lid is opened. • In order to open the enclosure lid loosen loosen the four enclosure lid screws. -
Page 30: Connection Quality
10 Troubleshooting SMA Solar Technology AG 10.2 Connection Quality The Bluetooth Repeater Outdoor can only display the connection quality if it is integrated into an existing SMA Bluetooth network. The SMA Bluetooth network can only be established by a master*. - Page 31 SMA Solar Technology AG 10 Troubleshooting Bluetooth LEDs Status Meaning Measure blue LED yellow LEDs The Bluetooth Repeater • Check the NetID. Outdoor is not connected to • Change the position of the Three LEDs off the Bluetooth network: Bluetooth Repeater Outdoor...
-
Page 32: Technical Data
11 Technical Data SMA Solar Technology AG 11 Technical Data General Data Width x height x depth 200 mm x 160 mm x 93 mm Weight with top-hat rail power supply unit 800 g Weight with Power Modul 740 g... - Page 33 SMA Solar Technology AG 11 Technical Data Ambient Conditions for Storage/Transport Ambient temperature − 40°C ... +70°C Relative humidity, non-condensing 10% … 95% Altitude above mean sea level (MSL) 0 m … 2,000 m Communication Bluetooth Inverter Data logger Bluetooth Range in open air ≤...
-
Page 34: Contact
12 Contact SMA Solar Technology AG 12 Contact If you have technical problems concerning our products, please contact the SMA Service Line. We require the following information in order to provide you with the necessary assistance: • Type, serial number and firmware version of the inverter •... -
Page 35: Declaration Of Conformity
Legal Provisions The information contained in this document is the property of SMA Solar Technology AG. Publishing its content, either partially or in full, requires the written permission of SMA Solar Technology AG. Any internal company copying of the document for the purposes of evaluating the product or its correct implementation is allowed and does not require permission. - Page 36 SMA Solar Technology www.SMA-Solar.com SMA Solar Technology AG SMA Solar India Pvt. Ltd. www.SMA.de www.SMA-India.com SMA Australia Pty. Ltd. SMA Italia S.r.l. www.SMA-Australia.com.au www.SMA-Italia.com SMA Benelux bvba/sprl SMA Japan K.K www.SMA-Benelux.com www.SMA-Japan.com SMA Beijing Commercial Company Ltd. SMA Technology Korea Co., Ltd.
Need help?
Do you have a question about the BTREP-OUT.GR1 and is the answer not in the manual?
Questions and answers