Summary of Contents for Diamond DIA-250
- Page 1 DIA-250 / DIA-376 / DIA-245 T ELEPHONE SER GUIDE AND INSTALLATION MANUAL FLUSH FITTING OR INTEGRATED 1 / 32 250S-UK1.DOC...
-
Page 2: Table Of Contents
1.5 TECHNICAL CHARACTERISTICS OF TLS TELEPHONE ....................6 - 7 1.6 DESCRIPTION OF DIA-250 S TYPE TELEPHONE ........................8 1.7 DESCRIPTION OF TYPE DIA-250 S1 CLD TYPE TELEPHONE ....................9 1.8 DESCRIPTION OF KEYPAD ..............................10 2. INSTALLATION OF TELEPHONES ............................11 2.1 INSTALLATION OF DIA-250 S .............................. -
Page 3: Presentation
1. PRÉSENTATION 1.1 TELEPHONE TYPES FLUSH FITTING WEATHERPROOF HANDS FREE TELEPHONE WITH KEYBOARD FOR CLEAN ROOM DIA-250 (See page 8) INTEGRATED WEATHERPROOF HANDS FREE TELEPHONE WITH KEYBOARD FOR CLEAN ROOM DIA-250S (See page 9) 3 / 32 250S-UK1.DOC... -
Page 4: General Characteristics
1.2 GENERAL CHARACTERISTICS QUIPMENT FOR STERILE AREAS HANDS FREE WEATHERPROOF TELEPHONES SERIES DIA-250 / DIA-376 / DIA-245 EGREE OF PROTECTION IP65 ( ON FACE PLATE OTES IP65 HESE PRODUCTS CONFORM TO WEATHERPROOFING CLASSIFICATION HE GUARANTEES IS VALID ONLY WHERE PRODUCTS ARE INSTALLED AND... -
Page 5: Contents Of The Package
1.3 CONTENTS OF THE PACKAGE The equipment you have received comprises: • A telephone set • A user manual • Mounting template. 1.4 GENERAL DESCRIPTION OF TLS TELEPHONES The « Hands free » weatherproof telephones are Automatic Central Battery (ACB) telephones without handset which can be used in centrally powered networks or installations within the voltage limits permitted by our equipment (see technical characteristics). -
Page 6: Technical Characteristics Of Tls Telephone
1.5 TECHNICAL CHARACTERISTICS OF TELEPHONE MPORTANT HESE MICROPROCESSOR BASED PRODUCTS WHEN CONNECTED TO THE TELEPHONE LINE CARRY OUT AN AUTO TEST BY TRANSMITTING AUDIBLE SIGNALS HEY ARE EQUIPPED WITH MANY PROGRAMMABLE FUNCTIONS AND ARE FACTORY CONFIGURED FOR NORMAL USE EFORE INSTALLATION READ THIS MANUAL CAREFULLY TO BE SURE THE FACTORY SETTING SUITS THE DESIRED USE The «... - Page 7 TECHNICAL CHARACTERISTICS Ringing call voltage > 35 V RMS 25Hz or 50Hz • • Current in the telephone (off-hook position) 35mA (20mA minimum) Voltage at terminals (on-hook position) 48V (24V minimum) • • Dialing system DTMF or Pulse • Dialing tone Continuous tone Frequency: 270 to 540Hz Detection time 2 sec.
-
Page 8: Description Of Dia-250 S Type Telephone
1.6 DESCRIPTION OF FLUSHFITTING TELEPHONE TYPE DIA-250S ACB-type flush fitting telephone set with weatherproof faceplate (IP65) comprising a painted steel-plate backing-case and a stainless faceplate with a self-adhesive polyester plaque with integrated keypad. The unit is closed by clipping the faceplate on to the backing-case. 8 / 32 250S-UK1.DOC... -
Page 9: Description Of Type Dia-250 S1 Cld Type Telephone
1.7 DESCRIPTION OF INTEGRATED TELEPHONE TYPE DIA-250 S ACB-type flush fitting telephone set with weatherproof faceplate (IP65) comprising a painted steel-plate backing-case and a stainless faceplate with a self-adhesive polyester plaque with integrated keypad (to be stuck on to the panel). The unit is closed by clipping the faceplate on to the backing-case. -
Page 10: Description Of Keypad
1.8 DESCRIPTION OF KEYPAD 15 button weatherproof keypad with on-line reassurance indicator. Legend and layout are identical for both telephone sets. LAST NUMBER REDIAL RECALL OR ONE-TOUCH MEMORY M1 ON-LINE INDICATOR CALL BUTTON SPECIAL BUTTON FOR ACCESS TO "STAR SERVICES" NOTE : Programming 10 direct memory access for keys 0 to 9 is allowed see chapter «... -
Page 11: Installation Of Telephones
2. INSTALLATION OF THE TELEPHONES 2.1 INSTALLATION OF DIA-250 S 4 COUNTERSUNK HOLES Diam.3.5 DRILLED AT 90 4 HOLES diam.11 OUT PLAN FOR INSERTION INTO A PANEL Cut out the panel according to measurements below (PARTITION SIDE 0.8mm MAX) For other thickness please ask us. -
Page 12: Dia-250 S1 Cl Mounting Instructions
DIA-250 S MOUNTING INSTRUCTIONS 4 SCREWS F/90M4/6LN - REFERENCE 2A - SQUARES - REFERENCE B - FRONT PLATE FASTEN CLAMPS BACKING CASE PANEL EP.= 0.8mm MAX PARTITION SIDE 4 COUNTERSUNK SCREWS F/90M3/12LN - REFERENCE 1A - CABLE ENTRIES FOR CABLE Diam.3 TO 20.5... -
Page 13: Installation Of Dia-250 S
INSTALLATION OF DIA-250 S 4 HOLES Diam. 3.5 DRILLED AT 90 HOLE Diam. 80 R=2.5 HOLE Diam.15 OUT PLAN FOR INSERTION INTO A PANEL Cut out the panel according to the values above 13 / 32 250S-UK1.DOC... -
Page 14: Dia-250S1 Cld Mounting Instruction
2.4 DIA-250 S MOUNTING INSTRUCTIONS BACKING CASE PARTITION SIDE FRONT PLATE CABLE ENTRIES FOR CABLE Diam.3 TO 20.5mm ADESIF POLYESTER FRONT roupe 1 – Cut out the panel according to the values above 2 – Fasten the face-plate on to the panel using countersunk screws. -
Page 15: Layout Of The Telephone Card
3. LAYOUT OF THE TELEPHONE CARD 3.1 FUNCTIONS AND JUMPER SETTINGS UNCTIONS EPAIRS JUMPERS ENSITIVITY OF THE HANDS FREE MICROPHONE Sensitivity up to 1m Sensitivity up to 30cm CEPTION LEVEL ADJUSTMENT Minimum setting : quiet location Maximum setting : noisy location NOTE : normal setting is carried out in factory (see drawing) 15 / 32 250S-UK1.DOC... -
Page 16: Connection Of The Telephone Set
For access to the telephone circuit, unclip the face-plate from the backing-case with the aid of screwdriver. For telephone type DIA-250 S : For access to the telephone circuit, unclip the backing-case with the aid of screwdriver. CONNECTION OF THE TELEPHONE LINE The connection of the unit to the telephone line is carried out on printed circuit board WK140MLB with the plug-in connector reference «... -
Page 17: Usage Of The Telephone With Full Keypad
4. USAGE OF THE TELEPHONE WITH FULL KEYPAD OW TO MAKE A CALL RESS THE CALL BUTTON The red indicator shows When the called party answers, speak in front of the telephone from a distance of Approximately 20cm (8in). At the end of conversation, to free the line : RESS THE CALL BUTTON OR ALLOW THE TELEPHONE TO CLEAR DOWN AUTOMATICALLY... - Page 18 AST NUMBER REDIAL RESS THE CALL BUTTON The red indicator shows BIS/LR RESS When the called party answers, speak in front of the telephone from a distance of Approximately 20cm (8in). At the end of conversation, to free the line : RESS THE CALL BUTTON OR ALLOW THE TELEPHONE TO CLEAR DOWN AUTOMATICALLY...
- Page 19 UTING MICROPHONE In noisy environment, it may be useful to activated or deactivate the microphone by pushing a key.( « R » key is used ) For this facility, program the unit as following : *24xx* = 0 Flashing time deactivated. *32xx* = 99 going «...
-
Page 20: Options
5. OPTIONS 5.1 RELAY BOARD – DOOR ENTRY / PUBLIC ADRESS (WK026CRG) This optional card connected via a flat ribbon cable to telephone card WK140MLB, enables the activation of a relay from a remote telephone or system. This relay can activate for example: •... -
Page 21: Amplifier Card Wk087Cra
5.2 AMPLIFIER CARD WK087CRA All variants can be equipped with this booster card which amplifies reception by 10-20 dBA subject to current available and the balance of the loudspeaker compared with the microphone. Can be fed by the line or a 1.5VA external source. Several applications are possible: 1/ Remotely fed by the telephone line and internal loudspeaker (minimum current 40mA). -
Page 22: Programming
6. PROGRAMMING The TLS telephone is designed to facilitate programming remotely over a telephone line. Programming is carried out using sequences keyed from a DTMF telephone, when connected to the TLS telephone to be programmed. 6.1 PROGRAMMING CODES IMPORTANT : Before all programming, key the access code : *1234* (factory setting) or as changed by the user (see function 12/13 below). - Page 23 Function Function Programming code AUTODIAL NUMBERS (If no chaining is required) If chaining is required, use function No5 instead (page 24) During memory programming , the combination #11# Represents the recognition of a continuous tone with a frequency of 440 Hz ± 100Hz (standard) before dialing. This is the standard for UK and many other countries but in Some other countries #10# may be applicable instead, Whereby a 2-second pause is inserted rather than tone...
-
Page 24: Loudspeaker Volume
Memory 1 *2400* TYPE OF DIALLING / CONFIGURATION Although this equipment can use either loop disc or DTMF Signaling only the performance of the DTMF signaling is subject to regulatory requirements for correct operation. It is therefore strongly recommended that the equipment is set up to use DTMF signaling for access to public or private emergency services. - Page 25 THE STEPS TO TAKE ARE : SINGLE-BUTTON TELEPHONE Program the main number in memory 1 and additional Numbers in memories 2-8. Program an empty memory following the last number entered, e.g., if two numbers are programmed, memory 3 should be empty : (factory preset) *5003** DUAL-BUTTON TELEPHONE Program lower button with memory 1 and either one or two...
- Page 26 If chaining 2 or several numbers, 2 choices are possible : a) to hear what actually happens on the line : program T1/T2 with even number (e.g., :30 sec) b) to mask what happens on the line (no-answer, busy tone,…) until the called party picks up, by simulating ringing and flashing LED.
-
Page 27: Activation Code
RELAY ACTIVATION TIME This should be set to *25DD* There is no limit to the relay activation duration. The relay is de-activated by pressing the * key or by hanging up. DD= 01 to 98 DD= 00 (no limit) Factory setting 02 (sec.) ACTIVATION CODE In the factory, the relay activation is set to 1. - Page 28 DURATION OF SILENCE BEFORE AUTOMATIC *13XX* CLEARDOWN XX = 30 30 seconds (factory setting) XX = 00 Does not clear down on duration of silence XX = 99 99 seconds Note : frequency tones are taken as silence. TYPE OF RINGING MODULATION *15XX* XX = 00 Pure Frequency (factory setting) XX = 01 3 Frequencies mixed...
- Page 29 MINIMUM TONE RECOGNATION/CLEARDOWN *34XX* FREQUENCY XX = 25 250Hz (factory setting) XX = 00 0Hz (range) XX = 99 990Hz MAXIMUM CLEARDOWN TONE FREQUENCY *35XX* XX = 50 500Hz (factory setting) XX = 00 0Hz (range) XX = 99 990Hz RETURN TELEPHONE TO FACTORY SETTING *98XX* ERASE MEMORIES...
-
Page 30: Operational Command Codes
7. OPERATIONAL COMMAND CODES Function Function Programming code REQUEST TELEPHONE ID *0600* This code is transmitted by the central system to determine the identity of a telephone calling the centre. The telephone will respond with its telephone ID (see programming code 18 above) AUTOMATIC CLEARDOWN At the end of a call without access to programming, the central system or operator can effect an automatic clear... -
Page 31: Maintenance
MAINTENANCE DIA telephones require little maintenance to remain in excellent operational condition. Carry out the following maintenance if necessary. XTERNALLY Clean using a dampened soft cloth. Do not use aggressive chemicals. Alcohol me be used to disinfect. 9. IN THE EVENT OF A PROBLEM Before consulting the maintenance service, we advise you to check the following points: ROBLEM WITH LINE CONNECTION OR DIALLING - Check telephone line correction on the connection terminal (see page 16) - Page 32 32 / 32 250S-UK1.DOC...