Summary of Contents for BECS BECSys2
- Page 1 Operator’s Manual TECHNOLOGY 9487 Dielman Rock Island Industrial Dr. St. Louis, MO 63132 Tel:(314) 567-0088...
-
Page 2: Table Of Contents
Operator’s Manual TABLE OF CONTENTS Section A: Programming the Controller ............................1 A - 1: Entering the Program Menu ............................. 1 A - 1.1: Selecting Language..............................1 A - 1.2: Setting the pH High Alarm Point..........................1 A - 1.3: Setting the pH Low Alarm Point..........................1 A - 1.4: Setting the ORP High Alarm Point.......................... -
Page 3: Section A: Programming The Controller
Operator’s Manual Section A: Programming the Controller A - 1: Entering the Program Menu To enter the program menu, press and hold both the Cal and Up key for 3 seconds. When the LCD A - 1.4: Setting the ORP High Alarm Point screen clears, release the keys and “Program”... -
Page 4: Section B: Normal Operation
Operator’s Manual Section B: Normal Operation B - 2.4: Modifying the Booster Trigger Point B - 1: Displaying the Set Points If relay 3 is configured for Cl/Br Booster control, To display the Set Points, press the Set Point key the screen will display boostr trig followed by the briefly. -
Page 5: B - 4: Alarms
Operator’s Manual B - 4.6: pH FAILSAFE ALM B - 4: Alarms During normal operation, the following alarms may be displayed. Some alarms will not be available Displayed when the active pH feed (feed up or depending on the system's configuration. feed down) attempted to feed continuously for the selected failsafe duration. -
Page 6: Section C: Maintenance
Operator’s Manual Section C: Maintenance The BECSys2 requires no maintenance other than a periodic calibration check and sensor cleaning. C - 1: Potentiometric Sensors (pH and ORP) C - 1.2: Long-Term Storage: C - 1.1: Electrode Cleaning: Save the wetting cap that came with the sensor for Slow response time and large offsets may indicate the long-term storage. -
Page 7: Section D: Feed Charts
Operator’s Manual Section D: Feed Charts Use the charts on the following pages to determine the correct amount of chemical to add to spa or pool water to achieve desired conditions. Choose which chart to use by the chemical indicated and the number of gallons to be treated. -
Page 8: D - 2: Pool Feed Charts
Operator’s Manual D - 2: Pool Feed Charts Quantity of Muriatic Acid Needed to Lower Total Alkalinity Desired Decrease Gallons in Pool In ppm 10,000 25,000 50,000 75,000 100,000 200,000 500,000 750,000 1,000,000 1.30 pt 1.62 qt 3.25 qt 1.22 gl 1.62 gl 3.25 gl 8.13 gl... -
Page 9: Section E: Installation Diagrams
Operator’s Manual Section E: Installation Diagrams E - 1: Pressure Filter Installation E - 2: Vacuum Filter Installation Page 7 TECHNOLOGY 9487 Dielman Rock Island Industrial Dr. St. Louis, MO 63132 Tel:(314) 567-0088... -
Page 10: Section F: Warranty
BECS will repair, or if repair is not possible, replace the defective part or parts of the BECSys controller. BECS will have the sole right to determine whether to repair or replace a product. BECS will not be responsible for any expense associated with installation of repaired or replacement parts. - Page 11 Saint Louis, Missouri is home to an exceptional design team, and all manufacturing is performed onsite at this facility where we can personally assure the quality of our products. The BECS commitment to excellence drives the most innovative new products and unparalleled customer service.
Need help?
Do you have a question about the BECSys2 and is the answer not in the manual?
Questions and answers