Case HI JX60 Service Manual page 14

◊ Use exclusively specified towing points for tow-
ing the tractor. Connect parts carefully. Ensure
that foreseen pins and/or locks are steadily fixed
before applying traction. Do not stop near towing
bars, cables or chains working under load.
◊ To transfer a failed tractor, use a trailer or a low
loading platform trolley if available.
◊ To load and unload the machine from the trans-
portation mean, select a flat area providing a firm
support to the trailer or truck wheels. Firmly tie
the machine to the truck or trailer platform and
block wheels as required by the forwarder.
◊ For electrical heaters, battery chargers and sim-
ilar equipment use exclusive auxiliary power
supplies with a ef ficient ground to avoid electrical
shock hazard.
◊ Always use lifting equipment and similar of
appropriate capacity to lift or move heavy compo-
nents.
◊ Pay special attention to bystanders.
◊ Never pour gasoline or diesel oil into open, wide
and low containers.
◊ Never use gasoline, diesel oil or other flammable
liquids as cleaning agents. Use non flammable
non toxic proprietary solvents.
◊ Wear protection goggles with side guards when
cleaning parts using compressed air.
◊ Do not exceed a pressure of 2.1 bar, in accor-
dance with local regulations.
◊ Do not run the engine in a closed building without
proper ventilation.
◊ Do not smoke, use open flames, cause sparks in
the nearby area when filling fuel or handling
highly flammable liquids.
◊ Do not use flames
on a machine or checking for leaks.
◊ Move with caution when working under a tractor,
and also on or near a
accessories: helmets, goggles and special foot-
wear.
◊ During checks which should be carried out with
the engine running, ask an assistant to seat at the
operator s seat and keep the service technician
under visual control at any moment.
as light sources when working
tractor. W ear proper safety
◊ In case of operations outside the workshop, drive
the tractor to a flat area and block it. If working on
an incline cannot be avoided, first block the trac-
tor carefully. Move it to a flat area as soon as pos-
sible with a certain extent of safety.
◊ Ruined or plied cables and chains are unreliable.
Do not use them for lifting or trailing. Always han-
dle them wearing gloves of proper thickness.
◊ Chains should always be safely fastened.
Ensure that fastening device is strong enough to
hold the load foreseen. No persons should stop
near the fastening point, trailing chains or cables.
◊ The working area should be always kept CLEAN
and DRY. Immediately clean any spillage of
water or oil.
◊ Do not pile up grease or oil soaked rags, as they
constitute a great fire hazard. Always place them
into a metal container.
Before starting the tractor or its attachments,
check, adjust and block the operator s seat. Also
ensure that there are no persons within the trac-
tor or attachment operating range.
◊ Do not keep into your pockets any object which
might fall unobserved into the tractor s inner
compartments.
◊ Whenever there is the possibility of being
reached by ejected metal parts or similar, use
protection eye mask or goggles
helmets, special footwear and heavy gloves.
◊ Wear suitable protection such as tinted eye
protection, helmets, special clothing, gloves and
footwear whenever it is necessary to carry out
welding procedures. All persons standing in the
vicinity of the welding process should wear tinted
eye protection. NEVER LOOK AT THE WELD-
ING ARC IF YOUR EYES ARE NOT SUITABLY
PROTECTED.
◊ Metal cables with the use get frayed. Always
wear adequate protections (heavy gloves, eye
protection, etc.)
◊ Handle all parts with the greatest caution. Keep
your hands and fingers far from gaps, moving
gears and similar. Always use approved protec-
tive equipment, such as eye protection, heavy
gloves and protective footwear.
with side guards,