Table of Contents
Advertisement
Quick Links
ELECTRIC CHAMFERING TOOL
Please read this manual carefully before you attempt to use
your tool so that you may use it properly and safely.
MINI BEVELER
PROFESSIONAL TOOL
Due to continuous product development/improvement the specifications and configurations in this
document are subject to change without prior notice.
Keep the manual handy – so you can use it whenever necessary.
Model
Power Source (Single Phase)
Rated Power Consumption
Rated Time
Rated Speed (No Load)
Stainless Steel
Chamfering Capacity
Mild Steel
Chamfering Angle
Mass (Weight)
No Load
Sound Pressure Level
Load
No Load
Sound Power Level
Load
No Load
Vibration Level
Load
Model EMB-0307B
Specifications
230V ∼ 50/60Hz
0C - 3C, 2R, 3R, 4R
0C - 7C, 2R, 3R, 4R
Motor
Knob
Motor
knob
Manufactured by :
NITTO KOHKI Co., Ltd.
2-9-4, Nakaikegami, Ohta-ku,
Tokyo, 146-8555, Japan
TEL
: (81)-3-3755-1111
FAX
: (81)-3-3753-8791
E-mail : overseas@nitto-kohki.co.jp
URL
: www.nitto-kohki.co.jp
Original Instructions
EMB-0307B
1100W
Continue
-1
11,000min
15°- 45°
3.9 kg
84 dB(A)
95 dB(A)
97 dB(A)
108 dB(A)
2
3.8 m/s
2
1.6 m/s
2
10.1 m/s
2
4.9 m/s
Advertisement
Table of Contents
Related Manuals for Nitto EMB-0307B
Summary of Contents for Nitto EMB-0307B
- Page 1 4.9 m/s Due to continuous product development/improvement the specifications and configurations in this document are subject to change without prior notice. Manufactured by : NITTO KOHKI Co., Ltd. 2-9-4, Nakaikegami, Ohta-ku, Tokyo, 146-8555, Japan : (81)-3-3755-1111 : (81)-3-3753-8791 E-mail : overseas@nitto-kohki.co.jp : www.nitto-kohki.co.jp...
-
Page 2: Table Of Contents
9. ORDERING SERVICE PARTS ………………………… 9 Landessprache. 10. OPTIONAL PARTS ……………………………………… 9 French : S'il vous plait, veuillez demandez ・ 11. EXPLODED DIAGRAM : EMB-0307B ……………… 10 á votre foumisseur de manuel instruction en langue locale. Spanish : Por favor, cantacte con su ・... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY BEFORE OPERATION INSTRUCTIONS Inspect tool before use. ● Before using, check that screws are securely When using the tool, please observe the safety tightened, that any protective cover or guard is precautions below to prevent possible accident or securely in place, other parts are free from damage injury. -
Page 4: General: Power Tools
Use of improper parts may result in serious accident. Turn off the switch and disconnect the power To obtain a Nitto genuine part, consult this Manual ● supply plug from power source before setting... -
Page 5: Instructions For This Tool
Use of power is limited to the power source ● Package Contents Check specified by the rating plate. MINI BEVELER EMB-0307B 1set Operate under the power source the voltage ● Dust Box Ass’y 1set fluctuating rate of which is within ±10 % of the... -
Page 6: How To Operate The Tool
chamfering is required, set the tool at a chamfering level about 0.5 smaller than the desired one. Try a test cut. Then adjust the tool for accurate chamfering. Pan Head Screw M5×10 In the case of Mild Steel You can select chamfering levels from 0 to 7C freely. The maximum chamfering capacity for one-cut is Head Dust Catcher... - Page 7 (1) Loosen the Hex. Socket Head Cap Screws ① apply the tool to the workpieces. The Indexable (4pcs) on both ends on the Plate Guide ② of Head Inserts may be damaged if the Switch js set ③ . (Fig.6) on after Indexable Inserts are pressed on the (2) Move the Plate Guide ②...
- Page 8 side facing the Plate D by adjusting the Head, but Hold the motor firmly, and throw away the chips by impossible on the upper side facing the Plate C. For opening the lid. (Fig.12) making a radius tangential line cutting on the upper side, conduct in a following manner.
-
Page 9: How To Replace Indexable Insert
Remember that chamfering level changes depending PULL on the radii in this case. Hex. Nut M8① Hex. Nut M8① Hex. Socket Set Screw Hex. Socket Set Screw Knob 8×25 special① 8×25 special① Dimension Fig.15 Plate D Plate D Ball Shape DOWN Fig.13 Fig.16... -
Page 10: Condition For Use
In ordering parts and components give each part number, part name and quantity required. Because a cut-off brush is used, when it is Use only NITTO genuine parts. ● worn electricity is automatically cut-off. If this happens, replace the carbon brush according to 10. -
Page 11: Exploded Diagram : Emb-0307B
This diagram is for your reference only. Do not attempt to service or repair the Tool. Do not take the Tool apart. Contact an authorized Nitto dealer for all service and repair of the Tool. Improper service and repair can cause... -
Page 12: Indexable Insert Set Screw 4 7
The part numbers with ( ) are included in the Ass’y parts written above them. No. Part No. Description Qty Price No. Part No. Description Qty Price TB02632 Plate C Ass'y 1set 49 (TQ04214) Retaining Ring 2 (TP16975) Label A (Caution) TQ12612 Pan Head Tapping Screw 4×25 3 (TQ01684) Label B (Chamfering level) -
Page 14: Ec Declaration Of Conformity
Tel: (65)-6227-5360 Fax:(65)-6227-0192 Tel: (1)-630-924-9323 Fax:(1)-630-924-0303 http://www.nitto-kohki.co.jp/e/nksb/ http://www.nittokohki.com/index.html NITTO KOHKI Co., Ltd. Shanghai Representative Office NITTO KOHKI EUROPE Co., Ltd. #1117 Ruijing Building, Maoming South Road, Unit 21, Empire Centre, Imperial Way, Shanghai 200020 China Watford Hertfordshire, WD24 4TS, United Kingdom...