Page 2
Introduction Thank you for purchasing our products and please contact us at any time if you have any question or need. Applicable Model This Manual is applicable to the following models: Channel HDD Number series 4/8/16 ch 1/2/4 HDD H.264 POE 4/8/16/32 ch 1/2/4/8 HDD Standard H.264...
Page 3
Disclaimer This Manual may contain inaccuracies, unconformities in product function operation or misprints. Our company will update the contents of this Manual according to the enhancement and change of product functions and regularly improve and update the software and hardware products described in this Manual. The updated information will be reflected in the latest version of this Manual without notice.
Page 4
Sign Description It indicates that there is a moderate or low-level potential danger which may result in minor or moderate injury if it cannot be avoided. It indicates that there is a potential risk that the device damage, loss of data, performance degradation or unpredictable results may be caused if these texts are ignored.
Contents 1、Overview of Product Functions ...................... 10 2、Operation Instructions ........................15 2.1、Introduction and Description of Front Panel ............15 2.2、Introduction and Description of Back Panel ............20 2.3、Mouse Operation Description ................. 25 3、Installation and Connection ......................27 3.1、Installation Precautions ................... 27 3.2、Hard Disk Installation .....................
Page 6
4.3.7、POE Power Information .................... 54 4.3.8、Encoding Setting ....................... 54 4.3.9、Video Setting ......................57 4.3.10、OSD Superposition Parameter Setting ..............62 4.3.11、Motion Detection ....................64 4.3.12、Mask Alarm ......................66 4.3.13、Alarm Input Setting ....................66 4.3.14、Video Loss Alarm Setting ..................68 4.3.15、PTZ Control ......................68 4.4、Preview ........................
1、Overview of Product Functions Introduce the main functional characteristics which need to be known by users when using the NVR. Basic Functions Support the access of network device; the webcam, webdome and network video server as well as the third-party webcam can be accessed. ...
Page 11
Support a variety of mainstream PTZ control protocols and support the presetting bit, cruising path, track setting and call. Hard Disk File Management Support the hard disk SMART information display. Support the bad track detection. Support the hard disk attribute setting: redundancy, read only, read-write and backup.
4 recording time periods can be set every day and the recording trigger modes of different time periods can be set independently. Support the holiday plan. Support to inquire videos according to the channel numer, recording type, starting and ending time, file type and other items.
Page 13
Support the rapid backup by channel and time. Support the management and maintenance of backup device. Alarm and Exception Management Support the arming time setting of alarm input/output. Support the video loss, motion detection, video mask, port, VCA, detection or port, detection and port and other alarm detections.
Page 14
Support the TCP/IP protocol stack and support PPPoE, DHCP, DNS, DDNS, NTP, SADP, NFS, HTTPS and other protocols. WEB server is embedded. Support the unicast and multicast and support TCP, UDP and RTP protocols during unicast. Support the remote search, playback, download, locking and unlocking of recording file.
Provide the development support and development training service of application system. Description: The main functions supported by our NVR are listed in the product function part and the functions of different models are different due to different positions and configurations, so please in kind prevail.
Page 16
It is the network status lamp which flashes under the network communication status. Interface USB It can connect with the mouse, U disk, mobile hard interface disk and other external devices. The front panels of NR40 standard series NVR (1/2/4 HDD) and NR50 standard series NVR (1 HDD) are shown below: The functions of front panel status lamps of NR40 standard series NVR (1/2/4 HDD) and NR50 standard series NVR (1 HDD) are shown below:...
Page 17
The functions of front panel status lamps of NR40 standard series NVR (8 HDD) and NR50 standard series NVR (8 HDD) are shown below: Type Name Description Status Ready It is the host-ready indicator which flashes when lamp the device is power on and works normally. Status The status lamp is on under the control of remote control.
Page 18
Button Number It is used to select the displayed channel screen button under the preview status and the displayed channel screen corresponds to the number button pressed; It is used to input numbers and characters under the editing status. Button Function It is used to conduct preset point call, zoom button...
Page 19
The front panel of NR50 enhanced series NVR (16 HDD) is shown below: The functions of front panel status lamps of NR50 enhanced series NVR (8 HDD) and NR50 enhanced series NVR (16 HDD) are shown below: Type Name Description Button POWER On-off button + power indicator.
2.2、Introduction and Description of Back Panel Introduce the descriptions for back panel and interface of device. The back panel interface of PSE series NVR (4-channel 1 HDD) is shown below: The back panel interface of PSE series NVR (4-channel 2 HDD) is shown below: The back panel interface of PSE series NVR (8-channel 2 HDD and 16-channel 2 HDD) is shown below: The back panel interface of PSE series NVR (16-channel 4-disk) is shown below:...
Page 21
The back panel interface of NR40 standard series NVR (4/8-channel 1 HDD) is shown below: The back panel interface of NR40 standard series NVR (4-channel 2 HDD and 8-channel 2 HDD) is shown below:...
Page 22
The back panel interface of NR40 standard series NVR (16-channel 2 HDD and 16-channel 4 HDD) is shown below: The back panel interface of NR40 standard series NVR (16-channel 8 HDD and 32-channel 8 HDD) is shown below:...
Page 23
The back panel interface of NR50 standard series NVR (20-channel and 40-channel 4 HDD) is shown below: The back panel interface of NR50 standard series NVR (20-channel 2 HDD) is shown below:...
Page 24
The back panel interface of NR50 standard series NVR (20-channel, 40-channel and 80-channel 8 HDD) is shown below: The back panel interface of NR50 enhanced series NVR (20-channel, 40-channel and 80-channel 8 HDD) is shown below: The back panel interface of NR50 enhanced series NVR (80-channel and 160-channel 16 HDD) is shown below:...
The back panel interface of NR50 standard series NVR (20-channel, 10-channel and 5-channel 1 HDD) is shown below: Description: The diagram only shows the functions of front and back panel interfaces, and the specific chassis size shall be subject to the final product. 2.3、Mouse Operation Description After the USB interface of device is connected with the mouse, the device can be operated by the mouse.
Page 26
Turn directions under the PTZ control status. Set the area coverage in the mask, motion detection and video mask Press and alarm area setting. drag Drag the scroll bar of channel and time display. Exchange positions of two preview screens.
3、Installation and Connection 3.1、Installation Precautions Warning: Improper replacement of battery may cause an explosion danger, so it is not recommended to replace the battery directly by users. If replacement is needed, replace with the same type or equivalent type of battery only. NVR is a kind of special monitoring device.
Please buy the monitoring hard disk from the formal channels to ensure the quality and operating requirement of hard disk; our company recommends the Seagate monitoring hard disk. Make sure that no danger will be caused by uneven mechanical loads. ...
3.2.1、Hard Disk Capacity Calculation Method According to the recording requirements (recording type, retention time of recording data), calculate the total capacity needed by a hard disk video recorder and see the specific details in the appendix of this Manual. Examples: Bitrate File size/hour Bitrate...
Page 30
1、 Unscrew the screws at the back and side of chassis and remove the upper cover. 2、 Connect one end of hard disk data line to the SATA interface of NVR mainboard and connect the other end to the hard disk. 3、...
Page 31
Installation diagrams (II): 1、 Unscrew the screws at the back of chassis, remove the upper cover and fix the hard disk on the hard disk support of chassis. 2、 Connect one end of hard disk data line to the SATA interface of NVR mainboard and connect the other end to the hard disk.
Installation diagrams (III): (Installation diagrams of front hard disk) 1、Install the set screws of hard disk and insert them into the slot positions of corresponding hard disk on the front panel. 4、Local Configuration and Operation 4.1、Startup and Shutdown Startup 4.1.1、 Precautions: ...
When the power supply is abnormal, NVR cannot work normally and even NVR may be damaged, so the regulated power is recommended for power supply. 1. After the power is plugged in and the power switch on the back panel is turned on, the device will make a “tick”...
When the system displays “It is shutting down…”, do not turn off the power. Do not cut off the power forcibly when the device is running. 4.2、Startup Guide After the device is started, the simple configuration can be conducted for the device through the startup guide to ensure the normal operation of device.
Page 35
3、 After entering the permission identification interface, users shall log in for identification as the administrator “admin” user. Click “Confirm”to conduct ID confirmation and then enter the startup guide after identification is successful; if the identification is wrong for 5 times successively, the device will be locked for 5 minutes;...
Page 36
Default administrator: admin, default password: admin or 1111. 4、Enter the time & time zone setting interface and click “Apply” to set the time zone, time format and time; click “Next” to enter the next interface; click “Exit” to log out the startup guide.
Page 37
6、Enter the format disk interface and click “Initialization” to conduct the formatting operation for the selected disk; click “Back” to return to the previous interface; click “Next” to enter the next interface; click “Exit” to log out the startup guide. Description: ...
Page 38
8、Enter the server search interface to conduct configuration for the digital channel. Click “Search” to search the digital channel. Click “Back” to return to the previous interface; click “Next” to enter the next interface; click “Exit” to log out the startup guide.
Page 39
9、 Enter the mobile monitoring interface to configure the mobile control device. Click “Back” to return to the previous interface; click “Next” to enter the next interface; click “Exit” to log out the startup guide. Description: The mobile monitoring mode of some device models is QQ, so please in kind prevail.
Page 40
11、If the disks which have not been formatted still exist in the system, the prompt shown in the figure below will pop up. Click “Do” to conduct formatting operation for the disks which have not been formatted in the system one by one automatically; click “Back” to enter the preview screen directly.
4.3、Channel Management 4.3.1、Shortcut Bar Channel Adding Users can add an IP channel to the device by the one-key shortcut, and the preview status will be as shown in the figure below if no channel is added to the channel. 1、After entering the preview interface and clicking the channel display “+” mark, the server search window will pop up, as shown in the figure below.
Page 42
Description: Add channels by default port, user name and password; if the information of channel does not meet the default information, users can edit the “Manual Add” to add channels. 2、After the search is completed, the adding can be completed by double clicking on the search list or selecting the channel and click “Add”.
port of PSE series NVR; do not connect the network port to LAN; otherwise, the IPs of other devices in LAN will be automatically modified. 4.3.2、General Digital Channel Adding 1、Select “Main Menu->Channel Management->Channel Configuration->Basic Configuration” to enter the channel configuration interface, as shown in the figure below. Description: ...
Page 44
Click “Advanced” to conduct searching according to different connection modes, as shown in the figure below. 3、Select the IP channel to be added in the search list, click “Add” or double click the mouse to add the IP device to the idle channel of NVR, and support to select multiple IP channels for adding.
Page 45
Description: When the adding mode of digital channel of PSE-NVR is plug-and-play mode, the channel has been occupied. Manual adding 1、In the Channel Configuration->Basic Configuration interface, click “Manual Add” to enter the digital channel interface; when the device type is private protocol, it is shown in the figure below.
Page 46
When the device type is ONVIF, it is shown in the figure below. 3、Input the IP address or URL address of front-terminal device, input the user name, password and other information, and then click “Confirm” to finish the digital channel adding. Repeat this operation to finish the adding of other digital channels.
Description: If the device to be added is a multi-channel NVR, users can select the channel No. to be added in the “Device Channel” and add the corresponding multiple channels of one NVR at the same time. Conduct the smart adding, batch adding and adding according to the adding rules and target channel;...
4.3.4、Plug-and-play Setting To make it convenient for users to quickly add the devices in the same network segment, users can select the “Plug-and-play” function to conduct the channel adding. Three modes can be selected for the plug-and-play of channel configuration interface: 1) Not enabled: the plug-and-play function is not enabled and users can manually set the digital channel and connect the video.
The plug-and-play function will clear the list of added devices and automatically modify the IP address of front-terminal device searched, so it is recommended that clients shall pay much attention when using the plug-and-play function. If users select to add and set the digital channel manually, the plug-and-play shall not enabled.
Wherein: (1) In “Enable Identification”, 0: disable, 1: enable; (2) In “Stream Type”, 0: mainstream, 1: substream 2: picture stream; (3) In “Transfer Protocol”, 1: TCP, 2: UDP, 3: multicast (4) In “Connect mode”, 0: IP, 1: domain name, 2: active mode; (5) In “Preview Mode”, 0: flat tile on the display area, 1: keep the widescreen proportion display.
Page 51
The interface can display the channel No., attribute, version number and connection status of added front-terminal device and also the parameter import and export, remote upgrade, IPC reboot and other operations can be conducted. 2、Parameter import/export 1) Select the front terminal to be operated in the list of added equipment. 2) After clicking “...
Page 52
4) Export the front-terminal configuration parameters and click “Parameter Export” to make the configuration export interface pop up, as shown in the figure below. 5) Select the storage device, fill in the exported file name and click “Export” to export the front-terminal configuration;...
Page 53
3、Remote upgrade and IPC reboot 1) Select the channel to be upgraded or rebooted in the list of added devices. 2) After clicking “Remote Upgrade”, the IPC upgrade interface will pops up, as shown in the figure below. 3) Select the configuration file to be upgraded and click “Upgrade” to finish the IPC upgrade.
4) Click “Reboot IPC” and reboot the selected device remotely. 4.3.7、POE Power Information PSE series NVR has this function and other models do not have this function. 1、Select “Main Menu -> Channel Management -> Channel Configuration -> POE Power Information” to enter the POE power information display interface, as shown in the figure below. Description: ...
Page 55
Audio/video parameter 2、Select the channel to be set and set the audio/video parameter: Channel No.: select the channel with parameters to be set. The video compression parameter type includes mainstream (general), mainstream (alarm), customization 1 and customization 2. Encoding mode: the system supports H.264 and H.265 codes. Three encoding modes (high profile, main profile and baseline) can be selected.
Page 56
Stream Type: the combined type option provides 2 choices: “Video” and “Audio”. “Audio” includes video and audio information and “Video” only includes video information. Click “More Setting” to expand the setting options of quality, I-frame interval, audio code, audio type and input volume. ...
The encoding parameter templates of front-terminal IPCs of different models are different. Click the “More Setting” button to expand and collapse the setting options under the button. Key area setting Set the key area here after the front terminal which supports the key area is connected. The image displayed in the key area has higher quality.
Page 58
HD parameter 1、Select the channel to be set. 2、Set the format, video flip, mode and other parameters. Description: Brightness, contrast, saturation and hue can be adjusted from 1 to 100. Shutter speed can be adjusted from 1/100000 to 1 and the bigger the setting value is, the faster the response speed is.
Page 59
The video input parameters can be adjusted by the mouse wheel and the values can be increased or decreased by clicking icons. 3、After the setting is completed, click “Apply” to save the setting parameters. 4、 “Reset To Default” means that the default values of all parameters on this page are restored directly.
Page 60
Description: The brightness value of day and night can be adjusted from 0 to 100 and the values can be increased or decreased by clicking icons. The color to grey delay and grey to color delay can be adjusted from 0 to 120s. 5、The inside synchronization is shown in the figure below.
Page 61
Description: The day and night brightness values can be adjusted from 0 to 100 and the values can be increased or decreased by clicking icons. The color to grey delay and grey to color delay can be adjusted from 0 to 120s. 6、The day/night mode is shown in the figure below.
Description: The day/night brightness value can be adjusted from 1 to 100. The effective delay time of color2 grey/grey2 color is 0-120 seconds. 4.3.10、OSD Superposition Parameter Setting 1、Select “Main Menu” -> Channel Management -> OSD Superposition” to enter the OSD superposition parameter setting interface, as shown in the figure below.
Page 63
OSD superposition 1、Select the channel which needs OSD setting. 2、Conduct OSD setting for the channel. If the OSD position of this channel needs to be changed, you can directly drag the mouse on the OSD box for setting after checking the customized position. Description: ...
1、Select the channel which needs dynamic privacy mask setting. 2、Control the PTZ through the shortcut PTZ control panel and switch to the screen you want to cover. 3、Drag the mouse to set the video mask area and click “Add Area”. 4、The added areas are displayed in the list on the right and they can be deleted by clicking “Delete Area”.
Page 65
2、Select the channel which needs motion detection setting. 3、Set the arming time of motion detection, detection area and sensitivity; the operations are as follows: 1) Check “Dispose Motion Detection”. 2) Click “Arming Setting” to set the arming time of motion detection. 3) Draw the area to be detected on the channel video with the mouse.
The double lamps can be linked after the front terminal which supports the double lamp setting is connected. 4.3.12、Mask Alarm 1、Select “Main Menu -> Channel Management -> Mask Alarm” to enter the mask alarm interface, as shown in the figure below. 2、Select the channel which needs video mask setting.
Page 67
2、Select the input port No. to be set. 3、Select the alarm type. Description: Normally open alarm: an alarm is given when the alarm input port of front-terminal IPC is open. Normally closed alarm: an alarm is given when the alarm input port of front-terminal IPC is closed.
4.3.14、Video Loss Alarm Setting Set the video loss alarm and link the NVR device for prompting and recording when the video loss occurs in the channel. 1、 Select “Main Menu -> Channel Management -> Video Loss” to enter the video loss setting interface, as shown in the figure below.
2、Select the channel to be set. 3、Select the PTZ control protocol, address and serial port of this channel. After the setting is completed, the parameter copy can be conducted for other channels. 4、Click “Apply” to save the set parameters. Description: ...
Recording (Include timing, manual and all kinds of alarm link recording) This channel is being recorded and an alarm occurs 4.4.2、Descriptions for Right-click Menu of Mouse In the preview status, users can conduct the preview screen switching, preview settings, channel management, video playback, video opening and other operations through the right-click menu.
Page 71
Diagram of right-click menu of auxiliaryport Description for right-click menu item of mainport Name Description Main menu Enter the main menu of system. Preview settings Enter the preview settings interface. Customized preview Directly apply the specific number of screens and scene configuration set by users previously.
Page 72
Start switch Switch the display of next screen constantly according to the preview settings conditions, and start with the first screen after reaching the last screen. Mobile monitoring Download the mobile monitoring client and QR code of connecting device. Channels Enter the channel management interface.
Page 73
Name Description Preview Enter the preview settings interface. settings Single-scree Select the channel through the pull-down menu for single-screen switching. Multi-screen Change the preview mode through the pull-down menu options. Prev page Switch the previous screen. Next page Switch the next screen. Start Switch Switch the display of next screen constantly according to the preview settings conditions, and start with the first screen after reaching the last...
Description: For NR20-S series and NR20-E series NVRs, except for 20-channel device, VGA1/HDMI1 supports 64 screens at most and VGA2/HDMI2 supports 32 screens at most. Page up and down Click the “Prev Page” button on the right-click menu to switch to the previous screen and click the “Next Page”...
System Setting Backup Alarm Setting User Management 4.4.4、Easy Operation of Preview 1、Enter the preview status and select the channel to be operated by the left mouse button, namely the display shortcut bar below red box, as shown in the figure below. 2、The PTZ control, instant playback, manual snapshot, manual recording, electronic amplification, talkback, channel information editing and other operations can be conducted by using the quitmenu.
Page 76
Electronic Amplification Start/End Talkback Adjust Volume Low Delay/High Fluency View/Edit Channel Information View Encoding Parameter Instant playback Play back the video of this channel within 5 minutes; a prompt of “Instant playback fails” will appear if there is no video of this channel. Electronic amplification 1、Click .
2、 Scroll the mouse wheel for amplification or shrinkage; the amplified or shrunk area centers on the current position of mouse. 3、Users can also click the “+” and “-” at the upper left corner of screen for amplification and shrinkage. Amplification and shrinkage are all conducted around the center of current screen. 4、When the video is amplified, the left mouse button can still be used to drag the image to replace the amplified area.
Page 78
2、Preview Setting->Basic Configuration Interface Description: Output device: select a video output device in the pull-down list of “Output Device”, HDMI2/BNC, VGA/HDMI and VC (when the last channel is set as the virtual channel, VC is displayed here). Output resolution: 800*600, 1024*768, 1366*768, 1440*900, 1280*800, 1280*720, 1920*1080, 2560*1440, 2560*1600, 3840*2160, etc.
Page 79
Output mode: set the display effect of VGA output; four optional modes are supported: standard, soft, bright and highlight. Preview effect: the system selects “Auto” by default, which means that the substream preview will be conducted after startup. Best image quality: to ensure the preview effect, all channels use the mainstream for preview.
The output devices of standard series NVR (16 channels and 8 HDD and 32 channels and 8 HDD) model include HDMI2/BNC and VGA/HDMI1. The output devices of NR20-S series and NR20-E series NVRs (NR20xx-S8, NR20xx-E8 and NR20xx-E16) models include VGA1/HDMI1 and VGA2/HDMI2. ...
Page 81
When the decoding performance of device reaches the upper limit, the device will display the following prompt: “The decoding performance reaches the upper limit, please disable some channels manually”. Users can configure whether to enable this prompt and the details are shown in System Setting -> General Setting. It is disabled by default. Information prompt of system exception: When the relevant options in System Setting ->...
interface timeout to clicking icon can be inquired by clicking the icon, so as to prevent users from missing alarm information during leave. 2、After the link shout is set for the channel in the VCA, the single-screen of corresponding channel will pop up and the icon at the top right corner of screen will flash when an alarm occurs;...
4.5、PTZ Control 4.5.1、PTZ Parameter Setting Description: Before controlling the ball machine or PTZ of IP channel, users shall confirm the normal network connection between PTZ decoder and NVR and configure the PTZ decoder parameters in the device. The parameter setting of front-terminal IPC serial port is shown in the description of Section 4.3.15.
Page 84
control the oblique action of PTZ and click the button to start or stop the horizontal automatic operation of PTZ. button on the left side of “Iris” 2) Lens control: the lens iris will be stopped after the is clicked and the iris will be opened after the button on the right is clicked;...
6) Drag icon to drag the PTZ control window. 7) Click icon to shrink the PTZ control window. In PTZ shrinking status, click icon to return the PTZ control window. In PTZ shrinking status, press the left mouse button to control the PTZ direction of ball machine according to the moving direction of mouse.
Page 86
2、The cruise path setting description is shown as follows: 1) Cruise path information browsing Select the cruise path No. in the pull-down list of “Path No.”; after selecting a cruise point, the system will automatically display the corresponding preset of the cruise point and the dwell time of the preset.
5) Logging out cruise path setting interface If the “Confirm” button is clicked, all path editing operations conducted after entering the cruise path setting interface will be all saved in the system, and the system will log out the path setting interface simultaneously; if the “Cancel” button is pressed, the system will automatically ignore all editing operations and log out the path setting interface simultaneously.
Logging out PTZ control mode: click the 【ESC】 button in the PTZ control mode to return to the preview mode. 4.6、Recording 4.6.1、Recording Guide Enter the main menu and click “Recording Guide” to configure the schedule recording, motion detection recording, port alarm recording and VCA recording conveniently; the reference interface is shown in the figure below.
Page 89
2) Click the “Finish” button to save the configuration. 2、Motion detection recording setting guide 1) Select “Main Menu” -> “Recording Guide” -> “Motion Detection” to enter the “Motion Detection Alarm Setting” interface, as shown in the figure below. 2) Click “Finish” to save the configuration. 3、Port alarm recording setting guide 1) Select “Main Menu ->...
Page 90
2) Click “Finish” to save the configuration. 4、VCA recording setting guide 1) Select “Main Menu->Recording Guide->VCA” to enter the “VCA Setting” interface, as shown in the figure below. 2) Set the configuration parameters related to VCA in the “VCA Setting” interface and see the specific setting method in the chapters related to VCA.
3) Set the arming time period of selected channel and disposal mode of un-armed time in the “VCA Setting” interface. The arming configuration information of this channel can be copied to other channels. Click “Finish” to save the configuration. 4.6.2、Recording Setting Basic setting 1、...
Page 92
3、Select whether to conduct “Audio Recording” and enable “Redundant Recording/Snapshot”, “I-Frame Recording” and “Substream Recording”. When “Audio Recording” is not checked, only video data is saved in the recording file. When there is a redundant disk in the system and the “Redundant Recording/Snapshot”...
Page 93
Advanced Setting Main Menu” -> Recording Setting -> Recording Template -> Advanced Setting” to “ 1、 Select enter the advanced setting interface of recording template, as shown in the figure below. 2、Select the channel to be set. 3、Set whether to enable the ANR function of front-terminal IPC. If it is enabled, IPC will automatically start the local recording when IPC is offline, and it will automatically upload the video saved locally into NVR when IPC is online again.
Page 94
The holidy recording plan of current year can be configured. After the holiday plan is enabled, this recording plan is performed preferentially during the holiday. 1、 Select “Main Menu->Recording Setting->Recording Template->Holiday Plan” to enter the “Holiday Plan” interface, as shown in the figure below. 2、...
3、Check “Enable Holiday Plan” and select the holiday setting mode: “Per Date”, “Per Month” or “Per Week”. Input the start and end date of holiday. Click “Confirm” to save the configuration. 4、After the holiday plan is enabled, the holiday can be selected in “Date” of “Advanced Setting”...
Page 96
2、Set the disk group or quota. Disk group: the hard disk attached to NVR can be divided into multiple disk groups and users can specify the disk group where the recording file is located for each channel. Quota: specify the maximum disk space which can be occupied by the recording file of certain channel;...
Page 97
2) Select disk group. There are eight optional disk groups (1~8) in the pull-down box. disks included in the disk group. Check “Select All 3) Select disk for disk group. Set Disks” to select all available disk groups. A disk cannot be included in multiple disk groups simultaneously.
4) Set the picture quota. Set the maximum storage space occupied by the picture file of this channel; the unit is GB and 0 means no limit. 5) Save the setting. Click the “Apply” button to save the setting. Description: ...
3) Set the snapshot mode which can be divided into “Single-picture Snapshot” and “Multi-picture Snapshot”. 4) Set the time interval of snapshot; the unit is second. 5) Select whether to conduct ftp uploading operation for the snapshot picture. Click the “FTP Setting”...
Page 100
1、Select “Main Menu->Recording Setting->Rebuild Index” to enter the “Rebuild Index” interface, as shown in the figure below. 2、Click the “Continous” button to start the rebuilding operation. 3、In the index rebuilding process, users can log out the interface for other operations, but they cannot conduct the video playback.
4.7、Playback 4.7.1、Instant Playback In the preview interface, play back and select the recording file of channel within 5 minutes. In the preview status, use the left mouse button to select the channel to be replayed, and button on the easy operation menu to enter the “Playback” interface, as click the shown in the figure above.
5. Other playback operations. 1)Use the “Full Screen” button at the top right corner to enter the full-screen playback. 2)In the playback process, if there is no operation within a period of time, enter the full-screen playback automatically and log out the full screen by operating the mouse or keyboard again.
Description: During the event playback, the player will skip through the video according to the alarm time period of video and skip the time periods without alarm recording. 4.7.5、Tag Playback The video tag function can help users record the relevant personnel or site information at a certain time point during playing back the video so that the information can be taken out later at any time to conduct search and positioning operation for the video.
Page 105
Operation by tag playback 1、Enter the playback interface, select “Tag Playback” as the playback mode and enter the “Tag Playback” interface. As shown in the figure below. 2、Select the channel. 3、 Input the tag key work. If key words are not input, search all tags of selected channel in the specified date by default.
5、Play back the tag which appears on the progress bar and is indicated by a green inverted triangle. After the mouse is moved to the position indicated by an inverted triangle, the information prompt of tag name will be displayed automatically. As shown in the figure below.
Page 107
2、After the channel and date are selected, the playback operation is started. 3、Click at the lower left corner of interface to enter the smart retrieval interface. As shown in the figure. 4、Click the button at the bottom of interface to select the retrieval type.
Page 108
4.7.6.1 Tripwire and Perimeter Retrieval 1、Click the button to enter the line drawing interface of smart playback and conduct line drawing operations on the video, as shown in the figure below. button to start search. In the search process, the words of “VCA 2、Click the SEARCHING……”...
Page 109
4、 In the search process, the search will stop automatically by clicking other channels or other dates. Users can also click the “Stop Search” button or “Exist” button to manually stop the search or log out the smart retrieval. 4.7.6.2 Face Detection to enter the “Face Dection”...
3、In the search process, the search will stop by clicking the “Stop Search” button. The video will be positioned to the corresponding position by clicking the search result on the right side. 4.7.7、Time-phased Playback Time-phased playback function means that the recording time of certain channel within a day is averaged to multiple screens in accordance with the number of split screens for asynchronous playback, which can effectively improve the playback efficiency.
2、Select the playback channel and set the number of split screens; take the 4-split-screen setting as an example. 3、Select the date on the right side or click the “Play” button for time-phased playback. 4.7.8、Picture Playback Picture playback function means the pictures stored in the hard disk are played back, as shown in the figure below.
Description: Users can select the playback interval and play the pictures automatically. Users can also suspend the playback and click the left and right sides of picture to display the previous or next picture. 4.7.9、External File Playback External file playback function means that the recording files stored in U disk or mobile hard disk, light disk and other external storage mediums are played back.
2、Select “Refresh” and read the external storage mediums. 3、Click the files to be played to conduct the external recording files playback, as shown in the figure below. Description: Please make sure that U disk or mobile hard disk and USB driver have been connected to the device before the external file playback.
Page 114
2、Select “Channel”, “Type” and “Start and End Time” and click “Inquire”. 3、Double click a log in the log list to enter the “Playback” interface, as shown in the figure below.
Description: Playback progress can be controlled by the playback time bar at the bottom. The channel and time point corresponding to the selected log shall have recording files to play. 4.7.11、Auxiliary Function of Playback Single-frame playback When the video is playback, view the detail changes of screen by single-frame playback. Enter the playback interface and left-click to adjust the playback speed to “Single Frame”.
Page 116
2、Select the button of playback control bar to enter the electronic amplification interface. 3、The amplification factor can be adjusted by the seekbar at the top left corner or mouse wheel. 4、Press the left mouse button and drag to view different areas. Snapshot Conduct the snapshot operation in the video playback process.
corresponding to this time point and before and after when sliding the playback progress bar with the mouse. Specific operation steps are as follows: 1、Select one of playback modes described above to start the playback. 2、When the mouse stays in a area on the progress bar with video, there will be preview images.
Page 118
1、Select “Main Menu->Backup” to enter the backup interface, as shown in the figure below. 2、Click “Recording Snapshot” to display the recording situation of specified date intuitively. After the date is selected, click “Confirm” to help users select the start time and end time of recording query by date.
Page 119
Description: The recording snapshot function is not supported by the picture files. 3、After the query conditions are confirmed, if the “Start Back-up Identification” is checked, the identification window will pop up by clicking the “Backup” or “Inquire Backup” buttons, the identity authentication needs to be conducted first and then the next step can be entered.
Page 120
5、 After the query conditions are confirmed, click the “Inquire Backup” button to conduct the query operation for recording files. The recording query results can be presented in two modes: list and chart. List: Click the “Playback” icon or double click the row the file is in to play this file. Click the “Lock”...
Page 121
After clicking to select a screen, the video of 10S after this time point will be played; double click the preview image to play back the video. 6、Select the recording file to be backed up in the list or chart and click the “Backup” button. Enter the backup interface.
7、Select the backup medium and click the “Run” button to conduct the backup operation. 4.9、System Setting Manage the attribute of device in the system uniformly. 4.9.1、General Setting Basic settings 1、Select “Main Menu->System Setting->General Setting->Basic Settings” to enter the basic settings interface, as shown in the figure below. The local output display parameters of device, system time, time zone and NTP timing can be set.
Page 123
Enable startup guide: select whether to start the startup guide setting. Decoding performance reaches the upper limit: select whether the prompt information will pop up when the decoding performance of device reaches the upper limit. Hide status lamp: select whether to display recording, alarm and other status lamps in the preview interface.
4.9.2、Network Setting NIC 1 1、Select “Main Menu->System Setting->Network Setting->NIC 1” to enter the setting interface of NIC 1.
Page 125
2、Select “Auto Get IP Address” or “Manual Setting IP Address”. If selecting auto getting, the system will get IP address from the DHCP in network after reboot. 3、When “Manual Setting IP Address” is selected, the IP address, subnetmask, gateway and other information of device shall be specified.
Page 126
Description: Only the device with double network cards can display this interface. Once the polymerization mode is set, the network parameters of second network card will be filled automatically with no need to fill by users. PSE network card Description: ...
Page 127
1、Select “Main Menu->System Setting->Network Setting->PPPOE” to enter the PPPOE setting interface. 2、Set whether to boot auto-dial. 3、Input the username and password of PPPOE dialing. 4、Click the “Connect” button to start the PPPOE dialing operation immediately. 5、 Click the “Apply” button to save the setting information of PPPOE dialing in the system. If the “Boot Auto-Dial”...
Page 128
2、Select the application mode of IP permission. “Disable”, “Whitelist” or “Blacklist”. 3、Input the IP address which needs to disable access or allows access in the input box of IP address. 4、Click the “Add” button to add the IP address to the list. 5、Click “Apply”...
Page 129
2、Set whether to enable DDNS service. 3、Input the domain name of device. 4、Input the domain name or IP address of DDNS server. 5、Input the login ID or password of DDNS server. 6、Click the “Apply” button to save the configuration. 1、Select “Main Menu->System Setting->Network Setting->FTP” to enter the FTP setting interface.
Page 130
2、Input the server address, port No., username and password of FTP server. 3、Click the “Apply” button to save the configuration. Email 1、Select “Main Menu->System Setting->Network Setting->Email” to enter the Email setting interface. 2、Input the Email server address, port No., username, password, encryption mode, recipient address and subject.
3、Click the “Apply” button to save the parameters set currently. Web service 1、Select “Main Menu->System Setting->Network Setting->Web Service” to enter the web service interface. FTP and HTTP ports of device can be modified in this interface. Users can also set whether to enable UPNP and SNMP service.
Page 132
2、The total remaining capacity and total capacity of current hard disk and virtual disk can be displayed in the interface. 3、Hot-swap. After a disk in the disk list is selected, the “Hot-swap” button is clicked and then the system pops up a prompt shown below; the hot-swap operation can be conducted for this disk after the “Confirm”...
Page 133
Description: The “Hot-swap” button will not be displayed for the devices which do not support the hot-swap function. 4、Disk detection. Set whether to detect all the disks after the device is powered off and rebooted and whether to repair the damaged disks. After the “Disk Detection” button is clicked, the disk detection window will pop up.
Page 134
Description: The file system will not be displayed for the devices which do not support the initialization format selection function of U disk. 6、Disk setting: set the disk purpose. The disk purpose includes four options: R/W, backup, redundant and read only.
Page 135
NFS setting 1、Select “Main Menu->System Setting->Disk Setting->NFS Setting” to enter the NFS setting interface. 2、Set the IP address (domain name) and directory of “NFS” service. 3、Click “Apply” to save the configuration. S.M.A.R.T. 1、Select “Main Menu->System Setting->Disk Setting->S.M.A.R.T.” to enter the SMART setting interface.
Page 136
2、Select the disk to be detected, check “Start S.M.A.R.T. Detection” and enable the S.M.A.R.T. detection function of this disk. S.M.A.R.T. detection information is displayed in the corresponding interface. 3、 When “Do not use this hard disk if self-evaluation is not passed” is selected, do not use this hard disk if there is a problem in self-evaluation after the S.M.A.R.T.
Page 137
2、Select the disk and detection mode and click the “Detection” button to enter the detection status. 3、Click “Pause” to make the bad track detection be in the paused status; click “Restore” to continue the bad track detection; 4、Click “Cancel” to cancel this bad track detection; 5、Click “Error Information”...
Description: “Error Information” can be clicked only when the error number of hard disk is more than 0; Stop the bad track detection when the error number of hard disk is equal to 100. “ ” means that the corresponding area of hard disk is in good condition, “ ”...
Page 139
2、Enable the array. After “Enable Array” is checked, it will take effect after the device is rebooted. 3、One-key configuration. After “Array Name” is input and the “One-key Configuration” button is clicked, the device will create arrays automatically. 4、Disk setting. After selecting a disk, click the “Disk Setting” button to set the disk as “Free Disk”, “Array Spare Disk”...
Page 140
2、 Create array. Click the “Create Array”button to enter the array creation interface, as shown in the figure below. The array name, array type and numbers of physical disks and spare disks which form arrays need to be specified for array creation. After all information is set, click the “Confirm”...
4、Delete array. Select the array to be deleted in the array list and click the “Delete” button to delete the selected array from the system. 4.9.5、Hot-spare Setting Enable the hot-spare system (Note: 4-channel and 8-channel NVRs and PSE series NVR do not support the hot-spare function);...
Page 142
system, the system will automatically switches to the hot-spare machine to work so as to ensure the continuity of video. A hot-spare system consists of several working machines and hot-spare machines and a working machine can set at most 16 hot-spare machines. When the hot-spare machine detects that the working machine is offline, the hot-spare machine will actively connect to the front-terminal IPC connected with working machine and start the video;...
Page 143
Hot-spare machine setting 1、 Select “System Setting->Hot-spare Setting” in the main menu to enter the hot-spare setting interface. 2、Select the hot-spare mode. 3、 After the “Apply” button is clicked, the system will prompts that it can take effect after the device is rebooted.
Page 144
5、 Select “System Setting->Hot-spare Setting” in the main menu to enter the hot-spare setting interface. 6、After the “Refresh” button is clicked, the working macines which open the hot-spare function are displayed in the working machine list; select the working machine which needs to conduct hot-spare operation.
7、After the “Add” button is clicked, the system will prompt to enter the login username and password of this working machine. After the verification is qualified, the IP and connection status of this working machine will be displayed in the working machine status list; if the password verification is not qualified, the IP of this working machine will also be displayed in the working machine status list, but the hot-spare machine status will be displayed as “Connection Fails”...
Page 146
2、Users can select the modules which need factory default configuration according to their needs; after the “Continous” button is clicked, the selected modules will be restored to factory default configuration. Description: Device will reboot automatically after being restored to default. Configuration Export 1、Select “Main Menu ->System Setting->Configuration Management->Configuration Export”...
Description: Device will reboot automatically after the configuration is imported successfully. 4.9.7、Log Management 1、Select “Main Menu->System Setting->Log Management” to enter the log query interface, as shown in the figure below. 2、After the channel, type, start time, end time and other query conditions are selected, click the “Inquire”...
3、After the logs are inquired, the logs can be viewed by selecting page up and page down through buttons, users can also input the page number and then click to skip to this page, and the log details can be viewed by clicking “Details” after the log is selected. 4、Log export operation: 1) After the log query is completed, the menu shown below will pop up by clicking “Export Current”;...
Page 149
Network error 1、Select “Main Menu->System Setting->Routine Maintenance->Network Error” to enter the network error setting, as shown in the figure below. 2、After the exception situation is checked, the corresponding link actions of system when this exception situation occurs, including OSD, voice prompt and upload center, can be checked.
Page 150
1、Select “Main Menu->System Setting->Routine Maintenance->Storage Error” to enter the storage error setting, as shown in the figure below. 2、After the exception situation is checked, the corresponding link actions of system when this exception situation occurs, including OSD, voice prompt and upload center, can be checked.
Page 151
2、 There are two optional modes: local upgrade and FTP upgrade; select the local file upgrade, click “Browse File”, select the file to be upgraded and then conduct the upgrade, as shown in the figure below. 3、Select the FTP upgrade, input the FTP server address, username, password and other information and then conduct the upgrade through FTP.
Page 152
Description: After the upgrade is successful, the device will reboot automatically and run the program of new version after reboot. If it is prompted that the upgrade fails or the device cannot run normally after reboot, please contact the supplier for processing. ...
5、The real-time network data will be displayed by “Network Flow”. 6、The application situation of network resource can be seen by “Network Resource Statistics”. 4.9.9、System Information System information 1、 Select “Main Menu->System Setting->System Information-> System Information” to enter the system information interface, as shown in the figure below. 2、...
Page 154
2、The channel No., channel name, connection status, motion detection status, video mask status, video loss status and other information can be seen through the channel status. Description: The video mask bar will not be displayed in the interface for the devices which do not support the video mask alarm function.
Page 155
2、The channel No., whether recording is being conducted, stream type, real-time frame rate/set frame rate, real-time bitrate/set bitrate, recording video resolution, recording type, compression parameter, redundancy and other information can be seen through the recording status. Alarm status 1、 Select “Main Menu->System Setting->System Information->Alert Status” to enter the alert status interface, as shown in the figure below.
Page 156
2、The network information related to network card can be seen through the network status. Description: The NIC 2 bar will not be displayed in the interface for the devices which do not support the double-network-card device. Hard disk status 1、...
2、The hard disk No., SMART detection status, size, free, attribute, disk group, total remaining capacity and total capacity of all hard disks and other information can be seen through the hard disk status. 4.9.10、Other Setting Serial port setting 1、Select “Main Menu->System Setting->Other Setting->Serial Port Setting” to enter the serial port setting interface, as shown in the figure below.
Page 158
The baud rate, data bit, stop bit, check and operation mode of local serial port of device can be set in this interface. Description: Local serial port can be used for external keyboard and cannot be used to control the analog PTZ.
Type management 1、 Select “Main Menu->System Setting->Other Setting->Type Management” to enter the type management interface, as shown in the figure below. Set the recording type name. 4.10、Alarm Setting 4.10.1、Alarm Input The prompting and recording can be conducted when an alarm occurs on the local NVR and the alarm situation needs to be input through the alarm input setting.
Page 160
1、Select “Main Menu->Alarm Setting->Alarm Input” to enter the alarm input setting interface, as shown in the figure below. 2、Select the input port No. to be set. The input port No. of local and host alarm can be set in this interface. 3、Set the input port alias.
7、Click “Apply” to save the set parameters. 4.10.2、Alarm Output 1、Select “Main Menu->Alarm Setting->Alarm Output” to enter the alarm output setting interface, as shown in the figure below. 2、Set the output port No. to be set. The output port No. of local and host alarm can be set in this interface.
6、Set the alarm output arming time. The arming date can be used with time period cooperatively. 7、 Copy to port. After the setting is completed, the parameter copy can be conducted for other alarm output ports. 8、Click “Apply” to save the set parameters. 4.10.3、Alarm Host Alarm host is added to expand the alarm input and output ports of device on the basis of local alarm input and output ports of device.
5、Set the communication port of network alarm host and restrict it to 18803; the communication can be conducted normally when the port No. of alarm host in network alarm host IE is set as 18803 simultaneously. 6、Set the number of alarm input ports of network alarm host. 7、Set the number of alarm output ports of network alarm host.
2、Select an alarm output port and click “Activate” or “Clear” to activate or clear the control; the current status of this port is displayed in the status bar of alarm output port; click “Activate All” or “Clear All” to activate or clear the control for all alarm output ports in the list and click the “Refresh”...
2、In the manual alarm clearing interface, select the alarm type to be eliminated; 6 options, including “All”, “Port Alarm”, “Motion Detection”, “Video Loss”, “VCA” and “Video Mask” are provided for user selection; click the corresponding button to eliminate the alarm of this type.
Page 166
Description: After the user is added successfully, the information of added user can be displayed in Basic Configuration->User List. At most 14 users can be added. There are 5 user groups in the system, including “Default User”, “Normal User”, “Privileged User”, “Superuser”...
4.11.2、User Permission Configuration 1、Click the in the user list to make the user permission editing window pop up, as shown in the figure below: 2、Permission description: 1) Local permission: it refers to the local operation permission, including manual alarm clearing, shutdown/reboot, log search, alarm setting, channel management, parameter setting, system setting and user management.
4.11.3、User Editing 1、Click the in the user list to make the user editing window pop up, as shown in the figure below:...
Page 169
Description: There are image unlocking and code protection setting options only when the user is admin; the original password needs to be input first when the admin user is edited and “Confirm” is clicked. 2、Image unlocking...
Page 170
1) After “Start unlocking image” is checked, the window shown in the figure below will pop up; the unlocking image can be set correctly after the same image drawn with more than 4 points is drawn twice according to the prompt. 2) Only the admin user can use the image unlocking.
Page 171
Users can set 2 code protection questions and select the customized question; the question must be filled in and shall not be null. 2) Verify code protection: if the code protection has been set, the admin user can click the “Forget Code” button to modify the password when logging in with password. As shown in the figure below:...
Page 172
After the “Forget Code” button is clicked, enter the code protection verification interface. As shown in the figure below: After the user inputs the correct code protection answer and new password, the password will be modified. If the new password is not input, the original password will not be modified after the code protection answer is verified.
4.11.4、Device Locking After the password unlocking failed for 5 times, it will enter the device locking interface as shown in the figure below. The locking time is 5 minutes. 4.12、VCA 1、Enter “Main Menu->VCA->Smart Configuration” and select the “Enable Arithmetic” tag page, as shown in the figure below.
Page 174
2、Select the channel to be set. 3、Select whether to enable front-terminal VCA or local VCA arithmetic. Description: Only some models support the local VCA, so please in kind prevail. 4、Check the arithmetic. 5、Click the “Save Arithmetic” button to save the arithmetic configuration. 6、Enter “Main Menu->VCA->Smart Configuration”...
Page 175
7、VCA parameter setting: Rule number: select the VCA rule; at most 8 rules are supported in each channel. Enable: set whether the rule will take effect. Rule name: set the rule name. Event: select the VCA events; tripwire, dual-tripwire, perimeter, article leaving, article loss, wandering, running and parking are supported.
Page 176
9、Click “Next” to set the target parameters, as shown in the figure below. 10、Users can set the target color, alarm color, detection sensitivity and other information. 11、Click “Next” to set the alarm link, as shown in the figure below. 1) Select the rule number to be set. 2) Check “Dispose VCA”, click arming setting and set the arming time.
Page 177
3) Enter “Disposal Mode” and set the VCA alarm link; the alarm link voice prompt, display, recording, alarm output, PTZ and snapshot can be set; if the camera connected with current channel supports the alert function and the alert is selected as event type, the link shouting, white light, alert laser and alert voice can be set and the single-screen of this screen is linked by default for the link shouting.
Page 178
Select the channel, set the start date and time, select the event type and then click the “Retrieve” button to enter the “Behavior Retrieval” interface, as shown in the figure below.
Description: The application method of facial retrieval and alert retrieval is the same as that of behavior retrieval. 15、Enter the “Main Menu->VCA->Alarm Information” interface to display the real-time alarm information, as shown in the figure below. The real-time alarm information of selected channel can be viewed in this interface. 4.13、Mobile Monitoring Users can download the mobile client by scanning QR code and input the user ID to conduct mobile video monitoring.
2、Users can select to download Android or IOS client according to their mobile operating systems, then scan ID QR code, conduct operation according to the prompt and conduct video preview, control and other operations by phone. 5、WEB Access 5.1、Introduction The Web service is embedded into the device, and users can input the IP address of device in the browser address bar when the device is connected to network to realize the remote WEB access.
1、Open the browser and input the IP address of NVR device. The “Login” interface pops up, as shown in the figure below: 2、Select the login language. 3、Input the correct user name and password, click “Login” and enter the preview interface, otherwise the prompt of “Login Fails”...
Page 182
The description for the icons in the preview interface is shown in the table below: Control Description Video is displayed by single-screen. Video is displayed by 4 screens. Video is displayed by 9 screens. Video is displayed by 16 screens. Video screen is displayed by a fixed proportion.
Page 183
Video screen is displayed by a proportion which fits into the window. Mobile monitoring QR code. Click the QR code to enter the mobile client download page. Connect all. Connect the videos of all channels. Previous page. Next page. One-key recording. Enable the remote manual recording of all channels.
5.4、Playback 1、Click the “Playback” tag page to enter the WEB playback interface. The video playback control buttons are shown in the list below. Control Description Switch mode to enter the playback interface of recording file list mode. Play recording file Pause playback Stop playback Single-frame step forward...
Page 185
Slow forward, divide playback speed by 2 Playback volume control Switch between synchronous playback and asynchronous playback Snapshot, click the button to save the video picture of this moment Cut recording file Cut recording file information list Single-screen playback Four-screen playback Full screen display Recording snapshot Timing recording...
Shrink time shaft Control button description: other button functions correspond to the button functions under the video playback time shaft mode. Control Description Browse local downloaded recording file and local recording file Display playback progress and length of recording file Playback progress control bar Home page of recording file query Previous page of recording file query...
2、The log query can be conducted by inputting query conditions and the query results can be backed up. Description: Save path of log file: D:\NetVideoBrowser. 5.6、Configuration 1、Click “Configuration” in the title bar to enter the configuration interface, as shown in the figure below.
Description: After the remote configuration parameters are modified, the local corresponding function configurations will also be modified. 6、Internet Keyboard 6.1、Keyboard Installation 1、Select the communication port and control the network port needed by embedded DVR. 2、Thread the power lines and control lines through the bottom shell, connect them to the correct positions and install the rubber barrier strip.
Blue background light, optional operation interface in Chinese/English and real-time displayed device status/programming information. B Key button area: Green button background light Button “1”: 1/sign Button “2”: 2/A/B/C Button “3”: 3/D/E/F Button “4”: 4/G/H/I Button “5”: 5/J/K/L Button “6”: 6/M/N/O Button “7”: 7/P/Q/R/S Button “8”: 8/T/U/V Button “9”: 9/W/X/Y/Z...
Page 190
When the buttons control the embedded DVR with blue button background light, their functions are shown below: 1、Stop playback of recording file 2、Enter the manual recording setting interface 3、Playback: switch the multiple-screen full-screen synchronous playback red box to the previous small screen 4、Enter the video preview screen setting interface 5、Under the playback mode, control the playback and suspension of recording file 6、Single-frame step forward: one frame is played every time the button is pressed when the...
MON: stop recording ALM: snapshot D Extended function button area: When the buttons control the embedded DVR with yellow button background light, their functions are shown below: Button F1: switch to main menu Button F2: switch to PTZ control status or enter full screen during the non-full-screen synchronous playback Button F5: quit to previous menu or play back to quit full screen Button F3: switch input method in numbers/Chinese Pinyin/lower-case English letters/capital...
【MODE】: control device selection; DVR shall be selected when the embedded hard disk recording host is controlled. 【PRI】: reserve. G Three-dimension vector gear shift rocker The functions realized by upward, downward, leftward and rightward actions of rocker include the following items. Upward: It is used to select the previous entry in the control menu.
3600 1024 d -bitrate, unit: Kbit/s Wherein: 2、After the recording time requirements are determined, calculate the storage capacity needed by single channel per hour according to Formula (2); the unit is MByte. q × h × D (2) h -daily recording time (hour) Wherein:...
Page 194
After 220V power is plugged, the “PWR” lamp 1) Power line is damaged of panel (2U chassis is “Ready”) is not on and 2) Switch power is damaged the chassis fan does not run when the power switch is turned on. After 220V power is plugged, the “PWR”...
Video and audio network transmission cannot be 1) One item or multiple items conducted by client. of IP address of hard disk video recorder, port No., user name and password input in “Local Configuration” in the client interface is/are incorrect 2) Network line is poor 3) Network interface of mainboard is damaged...
Need help?
Do you have a question about the H.264 POE SERIES and is the answer not in the manual?
Questions and answers