Table of Contents
Advertisement
Quick Links
MESSAGE LIBRARY
Refer to BBP-5 Instal Guide for information on input triggers.
The same message may be linked to more than one trigger.
A
BBREVIATED VERSION DISPLAYED IN
SELECTION SCREEN
<Blank>
SERVICER
(Default Custom Message)
DoorOpen
VentMode
RemoteOf
RemoteSh
CleanFil
ServiceR
NoWaterF
FanOverl
FireShut
ACPlantF
HPFault
LPFault
HP/LPFau
S1OpenCi
(Default Forced Vent Input Message)
S1Closed
(Default Remote On/Off Input Message)
S2Closed
(Default System Fault Input Message)
M
ESSAGE DISPLAYED ON SCREEN AFTER
TRIGGER IS ACTIVATED
SERVICE
REQUIRED
Door
Open
Vent
Mode
Remote
Off
Remote
Shutdown
Clean
Filters
Service
Required
No Water
Flow
Fan
Overload
Fire
Shutdown
AC Plant
Fault
HP
Fault
LP
Fault
HP/LP
Fault
S1 Open
Circuit
S1Closed
Circuit
S2Closed
Circuit
Touchpad User Guide
(Model: C-LCD-122-TL)
National Sales
Ph: 1300 306 125
sales@ias.net.au
Designed and Manufactured in Australia by:
Innovative Air Systems Pty Ltd.
Unit 1 / 49 Miller Street
Murarrie, Queensland, 4172.
Product Support
Freecall: 1800 354 434
support@ias.net.au
Advertisement
Table of Contents
Summary of Contents for IAS C-LCD-122-TL
- Page 1 BBREVIATED VERSION DISPLAYED IN ESSAGE DISPLAYED ON SCREEN AFTER SELECTION SCREEN TRIGGER IS ACTIVATED <Blank> SERVICER SERVICE (Default Custom Message) REQUIRED Door Touchpad User Guide DoorOpen Open Vent (Model: C-LCD-122-TL) VentMode Mode Remote RemoteOf Remote RemoteSh Shutdown Clean CleanFil Filters Service ServiceR Required...
- Page 2 4.2 To Edit the Timeclock Programs ....................8 4.3 To Set Holidays..........................9 4.3 To Set Daylight Savings........................ 9 5.0 Installation and Commissioning............10 5.1 Touchpad Dipswitch Confi gurations ................... 10 5.2 C-LCD-122-TL Connection Diagram ..................11 Auxiliary Socket Flow Proved LED Relay 5 LED DIP Switches...
- Page 3 5.0 Installation and Commissioning 1.0 Quick Start Options This controller provides a menu based user interface. The information that can be • Ensure all electrical connections are in accordance with the supplied connection dia- displayed at any given time is limited by the screen area of 2x8 character lines. Additional grams and local bylaws.
- Page 4 2.2 To Set the Fan Speed (Multi fan speed models only) NOTE: Active Programs (i.e. programs with a start or stop time or both, AND with active days) will appear in CAPITALS. (E.g. “PROG 02” = active; “prog 02” = not active) Operation: The Fan Speed enables the user to manually select the fan speed or set the fan to Auto.
- Page 5 4.0 Clock Menu Options To disable Setback, select a minimum of “----” and a maximum of “----”. These “----” settings are found by scrolling the minimum all the way down, and the maximum all the way up. NOTE: This clock section is only relevant if the optional clock module has been plugged in to the relay module.
- Page 6 • Select ‘Deadband’ from the settings sub-menu screen, then press enter to access 3.5 To Select the Forced Vent Input Message the deadband edit screen . • Select ‘Msg S1op’ from the settings sub-menu screen and press enter. • The cursor will highlight the deadband value. •...
Need help?
Do you have a question about the C-LCD-122-TL and is the answer not in the manual?
Questions and answers