Advertisement
CONTACT US
T 1300 798022
sales@claytonengineering.com.au
BRISBANE
26 French Avenue,
Brendale, Qld, 4500
T 1300 798 022
F 07 3881 2780
• INSTALLATION • OPERATION • TROUBLE SHOOTING •
For any assistance or after sales service call Leader on our toll free number 1300 798 022.
Please have a look at further quality Leader products at www.leaderpumps.com.au
L_DIV.OM_05.2012
MELBOURNE
24 Healey Rd,
Dandenong South, Vic, 3175
T 03 9706 9922
F 03 9706 9533.
DIVERTRON USER MANUAL
SUBMERSED CONSTANT PRESSURE SYSTEMS
• INSTALLATION • OPERATION • TROUBLE SHOOTING •
For any assistance or after sales service call Leader on our toll free number 1300 798 022.
Please have a look at further quality Leader products at www.leaderpumps.com.au
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Leader Pumps DIVERTRON
Summary of Contents for Leader Pumps DIVERTRON
- Page 1 DIVERTRON USER MANUAL SUBMERSED CONSTANT PRESSURE SYSTEMS CONTACT US T 1300 798022 sales@claytonengineering.com.au BRISBANE MELBOURNE 26 French Avenue, 24 Healey Rd, Brendale, Qld, 4500 Dandenong South, Vic, 3175 T 1300 798 022 T 03 9706 9922 F 07 3881 2780 F 03 9706 9533.
- Page 2 Dear Customer, Congratulations on purchasing this high quality Leader product. Please take a minute to read these installation and important 6. WARRANTY POLICY safety instructions before using your new equipment. 1. TECHNICAL DATA Clayton Engineering warrant this product for 2 years from the date of purchase. The warranty covers manufacturer’s defects in material or workmanship. The warranty does not cover malfunctions due to misuse or due to failure to follow the instructions in Power (w) 1100 the instruction manual. Any alterations to the product are to be performed by a Clayton Engineering approved service agent. Any repairs performed by non approved personnel Max Head (m) may void the warranty.
- Page 3 2. DISCHARGE LINE 5. TROUBLESHOOTING Before performing any troubleshooting operation, it is necessary to disconnect the pump 1. T he minimum recommended discharge line is 1” inside diameter rigid pipe. from the power supply by removing the pump systems plug from the electricity supply. 2. A barrel union needs to be fitted at the top of discharge pipe inside the rainwater tank. This fitting must be easily accessible by a person from the tanks leaf strainer / pump Problem Possible Cause Solutions access point. (See diagram) With out this the pump is not serviceable with out cutting Pump doesn’t stop There is a leak in the pipe Check all pipework for leaks. plumbing. when tap is closed system. (>.5 lpm) Pressure test using a gauge if 3. E nsure lock-ring of union is on the topside to eliminate risk of it falling into tank in the necessary. Any small leak from a event of servicing. connection, tap or leaking toilet will cause a problem. Pump starts but Insufficient water in tank Make sure there is sufficient water delivers no water to pump. The inlet screen or piping Clean pumps inlet screen.
- Page 4 3. OPERATION 4. STARTING THE PUMP The DiverTron pump is a unique product on the Australian market. It is unique because it has the pumps controller built into the pump that is then submersed inside the water 1. C onnect the pump unit to the electrical power outlet and turn the power on. tank. 2. T he pump starts automatically. Allow the pump to operate for approximately 30 The controller in the pump makes the system automatic. The pump unit performs three seconds to remove all air that may be in the system. If more than one tap, each tap will functions: need to be turned on to bleed the air out of the lines. 1. A utomatic pump operation: the pump starts when the tap is turned on and stops it 3. Close the tap. The pump will stop in approximately 10 seconds. about 10 seconds after the tap is turned off. Auto-Restart and Dry-run protection 2. P ump protection from dry operation: The pump stops when there is no flow of water, If no water has been pumped due to not enough water in tank, the pump will turn off to thus preventing possible damage to the pump. prevent damage. 3. Constant pressure: Provides constant flow and pressure. Priming cycle: When started , the pump will perform the following operation until it is The pumping unit will not work if the highest point of water delivery primed: exceeds a vertical height of 15 meters.
Need help?
Do you have a question about the DIVERTRON and is the answer not in the manual?
Questions and answers