Related Manuals for ADJ Saber Spot WW
Summary of Contents for ADJ Saber Spot WW
- Page 1 User Instructions A.D.J. Supply Europe B.V. Junostraat 2 6468 EW Kerkrade The Netherlands www.americandj.eu 2/17...
- Page 2 ©2017 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
-
Page 3: Table Of Contents
ROHS - A great Contribution to the Conservation of Environment ..................17 WEEE – Waste of Electrical and Electronic Equipment ......................18 NOTES ....................................19 NOTES ....................................20 A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 3... -
Page 4: General Information
Introduction: The Saber Spot WW is a DMX intelligent LED fixture. The Saber Spot WW can operate as a stand alone fixture or in a Master/Slave set up. The Saber Spot WW has three operating modes; WW dimmer mode, show mode, &... -
Page 5: Safety Precautions
DMX SET UP Power Supply: The ADJ Saber Spot WW contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. - Page 6 Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The Saber Spot WW can be controlled via DMX-512 protocol. The Saber Spot WW has 3 DMX channel modes. The DMX address is set electronically using the controls on the rear panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data output (Figure 1).
-
Page 7: System Menu
- This will let you set the unit as the slave in a master/slave configuration. 1. Press the MENU button until “SLAVE” is displayed, press ENTER. A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 7... - Page 8 1. Press the MENU button until “TempUnit” is displayed, press ENTER. 2. Use the UP or DOWN buttons to switch between Celsius or Fahrenheit. Press ENTER to select your desired setting. A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 8...
-
Page 9: Operation
A DMX controller allows you to create unique programs tailored to your individual needs. 1. The Saber Spot WW has 3 DMX channel modes. See page 11 for detailed description of the DMX values and traits. -
Page 10: Master-Slave Set Up
4. The slave units will now follow the Master unit. INSTALLING THE FROST LENS The Saber Spot WW Plus comes with 2 frost filters. Install the filter in front of the lens and put the inlcuded retainer ring top to hold the lens in place. -
Page 11: Channel Mode
DIMMER CURVES 0 - 20 STANDARD 21 - 40 STAGE 41 - 60 61 - 80 ARCHITECTURAL 81 - 100 THEATRE 101 - 255 DEFAULT DIMMER SETTING A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 11... -
Page 12: Dimmer Curve Chart
T rise (ms) Tdown (ms) Standard Stage 1100 1540 1660 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280 CAD DRAWING A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 12... -
Page 13: Photometric Chart
PHOTOMETRIC CHART Beam angle 4° Field angle 8° Intensity (LUX) Full LEDs 4° Diameter(m) 8° Diameter(m) A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 13... - Page 14 PHOTOMETRIC CHART (continued) Beam angle 10° (single face)frost filter Intensity (LUX) Full LEDs 10° Diameter(m) A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 14...
-
Page 15: Power Cord Daisy Chain
Trouble Shooting: Listed below are a few common problems that you may encounter, with solutions. No light output in WW Dimmer Mode; 1. Be sure the strobe setting is set to value 255. A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 15... -
Page 16: Specifications
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 16... -
Page 17: Rohs - A Great Contribution To The Conservation Of Environment
The ROHS directive is an important step to the protection of our environment. We, as manufactures, feel obligated to make our contribution in this respect. A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 17... -
Page 18: Weee - Waste Of Electrical And Electronic Equipment
We are happy to answer any of your inquiries and welcome your suggestions at: info@americandj.eu A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 18... -
Page 19: Notes
NOTES A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 19... -
Page 20: Notes
NOTES A.D.J. Supply Europe B.V. – www.americandj.eu – Saber Spot WW User Manual Page 20...
Need help?
Do you have a question about the Saber Spot WW and is the answer not in the manual?
Questions and answers