Table of Contents
Advertisement
Quick Links
Fingerprint Reader and Keypad
Features:
500DPI Optical fingerprint reader
Up to 1,000 users (up to 500 fingerprint
users, up to 500 PIN users)
User code length 4~6 digits
Fingerprint identification time – <1 second
Fingerprint false acceptance rate – 0.0001%
Fingerprint false rejection rate – 0.01%
SK-2611-SFSQ
Manual
12VDC Operation
Form C relay output
Tamper alarm output
Adjustable relay output time –
For indoor use only
Illuminated fingerprint reader window
®
1~99 seconds, or toggle
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ENFORCER SK-2611-SFSQ
Summary of Contents for ENFORCER SK-2611-SFSQ
- Page 1 SK-2611-SFSQ Fingerprint Reader and Keypad Manual Features: 500DPI Optical fingerprint reader 12VDC Operation Up to 1,000 users (up to 500 fingerprint Form C relay output users, up to 500 PIN users) Tamper alarm output User code length 4~6 digits ...
-
Page 2: Quick Installation Guide
ENFORCER Fingerprint Reader and Keypad Quick Installation Guide: This page is for installers looking to do a basic installation and programming of the fingerprint reader and keypad. For more in-depth installation and programming instructions, see "Table of Contents" on pg. 4. -
Page 3: Quick Programming Guide
ENFORCER Fingerprint Reader and Keypad Quick Programming Guide: Programming Tips: Master fingerprints (up to 5) should be programmed before any other programming is completed. A flashing red LED indicates that fingerprint reader/keypad is in standby mode. A solid blue or ... -
Page 4: Table Of Contents
ENFORCER Fingerprint Reader and Keypad Table of Contents: Quick Installation Guide: ......... 2 Sample Application: ..........7 Mounting Diagram: ..........2 Getting Ready to Program: ........7-8 Quick Wiring Diagram:..........2 Programming the Master Fingerprints: ....8 Quick Programming Guide: ........3 Programming User Fingerprints: ...... -
Page 5: Overview
ENFORCER Fingerprint Reader and Keypad Overview: " (150mm) " " (66mm) (24mm) Parts List: 1x Fingerprint reader and keypad 1x Manual 1x Diode 4x Mounting screws 4x Mounting screw anchors 1x Mounting bracket 2x Security screws 1x Security wrench LED Indicators and Fingerprint Reader/Keypad Sounds:... -
Page 6: Installation
ENFORCER Fingerprint Reader and Keypad Installation: 1. Find a suitable location to mount the fingerprint Fig. 1 reader/keypad. Install it at a height at which most users will be able to easily operate the unit. 2. Run wiring through the wall to the fingerprint... -
Page 7: Sample Application
ENFORCER Fingerprint Reader and Keypad Sample Application: Red – 12VDC (+) Orange – Output (COM) 12VDC Alarm (–) Power Gray – Tamper Alarm Output (GND) Supply Black – Ground (–) (–) Egress Yellow – Egress Input (N.O.) Button Blue – Output (N.O.) Electric (–) -
Page 8: Programming The Master Fingerprints
ENFORCER Fingerprint Reader and Keypad Getting Ready to Program (continued): 3. Exit programming mode: Press the key or wait 15 seconds to exit automatically. NOTE: DO NOT DISCONNECT THE FINGERPRINT READER/KEYPAD FROM POWER WHILE IN PROGRAMMING MODE. Disconnecting the unit while in programming mode may cause a memory error. -
Page 9: Programming User Codes
ENFORCER Fingerprint Reader and Keypad Programming User Fingerprints (continued): Examples: 1. Program a user fingerprint for User ID #10: 2. Program a user fingerprint to an automatically assigned User ID (generally not recommended, since the User ID will be needed to delete a user when their fingerprint is not available): ... -
Page 10: Programming The Output Mode And Output Timing
ENFORCER Fingerprint Reader and Keypad Deleting User Fingerprints or User Codes (continued): NOTE: For all programming functions, the fingerprint reader/keypad must first be in programming mode. To enter programming mode, present the master fingerprint once. Exit programming mode by pressing the key after all programming is completed. -
Page 11: Resetting The Fingerprint Reader/Keypad
ENFORCER Fingerprint Reader and Keypad Resetting the Fingerprint Reader/Keypad: When resetting functions on the fingerprint reader/keypad, use the following formula: – Reset the Fingerprint Reader/Keypad – System Restore Options System Restore Options: – Reset the output mode and time to the default setting (5 seconds). -
Page 12: Troubleshooting
ENFORCER Fingerprint Reader and Keypad Troubleshooting: Try a different finger (if more than one finger was originally Unit does not enter programming programmed) mode with master fingerprint Manually reset the master fingerprints Ensure the User ID assigned is between 1 and 500 Unit fails to accept a new fingerprint ...
Need help?
Do you have a question about the SK-2611-SFSQ and is the answer not in the manual?
Questions and answers