Summary of Contents for Optelecom 9000 Series 9973-C
Page 1
Four-Port 10/100 Mb Ethernet Switch A pair of 9973-C cards transports a 10 base T Ethernet signal via the duplex high-speed port available on many Optelecom video and data fiber transmission cards. It also includes a built-in four-port 10/100 Auto MIDX unmanaged switch.
Table of Contents Section Page Safety Instructions Instrucciones de Seguridad Sicherheitsanleitungen Consignes de Sécurité Fiber Information External Wiring Information Functional Description 9973-C Indicator, Connector, and Switch Locations Set Up and Operation of the 9973-C Typical Application of the 9973-C Troubleshooting 9973-C Links Operation of the 9973-C with Network Management Software Specifications...
Safety Instructions RM-3 The safety information contained in this section, and on other pages of this manual, must be observed whenever this unit is operated, serviced, or repaired. Failure to comply with any precaution, warning, or instruction noted in the manual is in violation of the standards of design, manufacture, and intended use of the unit.
Instrucciones de Seguridad RM-3 Debe observarse la información de seguridad contenida en esta sección, y en otras páginas de este manual siempre que se opere, dé servicio o repare esta unidad. Si no se cumple con alguna precaución, advertencia o instrucción indicada en este manual se infringen los estándares de diseño, fabricación y el uso destinado a la unidad.
Sicherheitsanleitungen RM-3 Die in diesem Abschnitt und auf anderen seiten dieses Handbuchs enthaltenen Sicherheitsinformationen müssen befolgt werden, wenn diese Einheit betrieben, gewartet oder repariert wird. Falls Vorsichtsmassnahmen, Warnungen oder Anweisungen in diesem Handbuch nicht befolgt werden, verstösst dies gegen die Konstruktions, und Herstellungsstandards und erfolgt im gegensatz zum vorgesehenen Verwendungszweck dieser Einheit.
Consignes de Sécurité RM-3 Les consignes de sécurité contenues dans cette section et dans le reste de ce manuel doivent être respectées a chaque fois que cet appareil est utilisé ou fait l’objêt d’une maintenance ou d’une réparation. Le non-respect d’une précaution, d’un avertissement ou d’une instruction figurant dans ce manuel est une violation des normes de conception, fabrication et indication d’usage de l’appareil.
Fiber Information This unit was manufactured with attention to fiber cleanliness by TKH Security Solutions USA. Beyond the optical safety information contained in this manual, the following guidelines should be observed when working with optical fibers. The biggest problem is dirt! It takes very little contamination to cause problems with optical fiber connections;...
Functional Description A pair of 9973-C interface cards provides a 10 base T Ethernet link via the duplex high-speed ports available on many video and data fiber transmission cards. The 9973-C has a built-in four-port, unmanaged 10/100 Ethernet switch. The cards operate on 6VDC as supplied by the chassis into which it is installed.
9973-C Indicator, Connector, and Switch Locations IGURE HIGH-SPEED PORT STATUS INDICATOR This three-color indicator provides status on the high-speed port connection to the opposite end of the link: (No Sync, No Loop), there is a problem with the signal being received from the opposite end of the link.
Page 11
10/100 ETHERNET SWITCH PORTS (PORTS 1 THROUGH 4) Each of the eight RJ45 Ethernet switch ports is 10/100 Ethernet, Auto Negotiate, and Auto MIDX. Each port has a yellow Full Duplex/Collision LED. This LED is always illuminated when the port is operating in Full Duplex mode.
Set Up and Operation of the 9973-C Set up and operation of the 9973-C cards consists of setting the high-speed cable length switch if necessary, installing the unit into a Series 9000 chassis, and connecting the Cat5 jumper cable from the high-speed port on the optical communications card to the 9973-C.
Typical Application of the 9973-C This application drawing shows a pair of 9973-Cs used in a system with the high-speed ports on a pair of 9252DT and DR cards. The combination provides eight simplex video, three built-in data ports on the 9252D pair, and the duplex high-speed port that is used by the 9973-Cs.
Operation of the 9973-C with Network Management Software Operation of the 9973-C with the Network Management System consists of the following parameters: Card Location Card Size (Number of Slots) Card Name (Model Number) Serial Number Revision Number Chronometer Value (Cumulative Hours of Operation) Reset Cycles (Cumulative Number of Power Cycles) Firmware Revision High-Speed Port Loop (Local Demux in Sync, and Remote Demux in Sync)
Specifications HIGH-SPEED PORT SPECIFICATIONS Connector RJ45 Data Format Synchronous RS422 @ 16 Mbps Duplex ETHERNET PORTS (X4) Connector RJ45 Data Format 10/100 Base T, MIDX, Full or Half Duplex, Auto Negotiate DATA PORTS 1 AND 2 SPECIFICATIONS Connector Five-position removable screw terminal Data Format RS232 (3-wire), RS422 2- or 4-wire, RS485 2- or 4-wire, Auto Baud up to 115.2 Kbps or Manchester (Burle, American Dynamics...