Summary of Contents for RHYNO RWC-50
- Page 1 RHYNO 18V 1/2” Impact Wrench -OPERATOR’S MANUAL - USA Catalog No: RWC-50 TO REDUCE THE RISK OF INJURY, USERS MUST READ AND UNDERSTAND OPERATOR’S MANUAL. Rev A 4/1/2017...
- Page 2 /min ……….. Per minute If you have any questions or comments bpm ………. Beats/min about this or any RHYNO tool, call us toll ipm …………. Inches/min free at: RPM ………… rotations/min sfpm ………. Surface feet/min 844-25RHYNO (844-257-4966) SPM ………..
- Page 3 Anvil Work Light Forward- Reverse Variable Speed Button Trigger Switch Fuel Gage Handle Battery Release Belt Clip Button Battery Pack...
- Page 4 Part Name Qty. Part Name Qty. Housing Star Screw Screw Reversing Lever Gear Box Switch Stator Belt Hook Rotor Star Screw Endbell Plate Battery Pack Back Cover Charger a) Power tool plugs must match the GENERAL POWER TOOL SAFETY outlet. Never modify the plug in any WARNINGS way.
- Page 5 protected supply. Use of a GFCI reduces a) Do not force the power tool. Use the the risk of electric shock. correct power tool for your application. 3) PERSONAL SAFETY The correct power tool will do the job a) Stay alert, watch what you are doing better and safer at the rate for which it common sense...
- Page 6 charger that is suitable for one type of • Wear safety goggles or other eye battery pack may create a risk of fire protection. Hammering and drilling when used with another battery pack. operations cause chips to fly. Flying b) Use power tools only with specifically particles can cause permanent eye designated battery packs.
- Page 7 Your tool uses a RHYNO charger. Be sure to read all safety work. To reduce your exposure to these instructions before using your charger. chemicals: work in a well ventilated area,...
- Page 8 If symptoms persist, seek Fuel Gage Battery Packs medical attention. RHYNO Battery Packs or tools include a fuel WARNING! Burn hazard. Battery liquid gage which consists of three green LED may be flammable if exposed to spark or lights that indicate the level of charge flame.
- Page 9 • These chargers are not intended for any • Do not place any object on top of the uses other than charging RHYNO charger or place the charger on a soft rechargeable battery packs. Any other surface that might block the ventilation...
- Page 10 Remove the battery pack from the tool • The charger is designed to operate on for charging when needed. RHYNO standard 120V/220V household Lithium-ion battery packs do not electrical power. Do not attempt to use develop “memory”...
- Page 11 flammable or combustible solvents around batteries, charger or tools. 4) REPAIRS The charger has no serviceable parts. Hot/Cold Battery Pack Delay When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the batty pack has reached an appropriate temperature.
-
Page 12: Variable Speed Trigger Switch
To install the battery pack into the tool Forward/Reverse Control Button handle, align the battery pack with the rails forward/reverse control button inside the tool’s handle and slide it into the determines the direction of the tool and handle until the battery pack is firmly also serves as a lock-off button. - Page 13 attachments or accessories. An accidental start-up can cause injury. WARNING! To reduce the risk of serious personal injury, ONLY use the tool's belt hook to hang the tool from a work belt. DO NOT use the belt hook for tethering or securing the tool to a person or object during use.
- Page 14 CAUTION: Ensure fastener and/or WARNING! Blow dirt and dust out of system will withstand the level of torque all air vents with clean, dry air at least once generated by the tool. Excessive torque a week. To minimize the risk of eye injury, may cause breakage and possible personal always wear ANSI Z87.1 approved eye injury.
- Page 15 To reduce the risk of injury, battery pack is tampered with in any only RHYNO recommended accessories way. RHYNO and We Cut The Glass, LLC should be used with this product. are not responsible for any injury caused Recommended accessories for use with...
- Page 16 We Cut The Glass, LLC. 4960 William Flynn Highway, Suite 6, #350, Allison Park, PA 15101 Toll Free: 844-25RHYNO, Fax 484-991-1952, Email: info@RHYNO.com © Copyright 2017 – We Cut The Glass, LLC. [16]...
- Page 17 (2) years after the date of purchase unless otherwise noted. Return of the tool to a RHYNO factory service center location, freight prepaid and insured, is required. A copy of the proof of purchase should be included with the return product.
Need help?
Do you have a question about the RWC-50 and is the answer not in the manual?
Questions and answers