Philips Philishave T388 Manual

English • Moustache trimming and clipping of single hairs
Precision trimmer
- Push the precision trimmer upwards and it will start
working immediately if the appliance is switched on
Important (fig. 13, 14). The precision trimmer is also suitable for
• Please read these instructions carefully and study straightening the edges of the beard in the neck and on
the illustrations, before using the appliance. the cheeks. Please note: the main cutting unit continues
• Before connecting the appliance, check if the working as well.
voltage indication on the appliance corresponds to
the mains voltage in your home. Cleaning
• Before first use, charge the appliance completely. - Always switch off the appliance before cleaning.
• Take care when using the trimmer the first couple
of times. Do not move too fast: make smooth and • During use:
gentle movements. - If much hair has accumulated in the comb area, pull off
• Regular cleaning and good maintenance guarantee the comb attachment (fig. 11) and remove the hairs by
optimum performance and a very long working life. shaking and/or blowing (fig. 15). The current beard length
• Do not allow the appliance to become wet. setting will be maintained.
• Do not expose the appliance to high temperatures
or direct sunlight. • After each trim:
• Keep the appliance out of children's reach. - Pull the comb from the appliance (fig. 11).
• Your trimmer is only designed for trimming the - Pull the cutting unit backwards (fig. 16).
human beard. Do not use the appliance for other - Clean with the brush (fig. 17, 18).
applications!
• Do not use abrasives or scourers, or liquids such Replacing the cutting unit
as alcohol, petrol or acetone for cleaning. If the cutting unit is damaged or worn, a new unit can be
• (If your appliance is marked with the following bought from the Philips Service Centre. Replace the cutting
text applies:) unit as follows:
To protect the environment, this appliance has - Remove the old cutting unit by first pulling it backwards
been equipped with a nickel-hydride (NiMH) battery (fig. 16) and then upwards.
which contains less than 0.01% cadmium. - Place the two notches of the new cutting unit into the
Still we advise you to make sure sure that, when you guide slots (fig. 19).
discard the appliance, you keep the battery separate - Push the cutting unit down ("Click"!) (fig. 20).
from normal household refuse and dispose of it at an
officialy assigned collection point. Please refer to Protecting the environment
section "Protecting the environment". The built-in rechargeable battery contains substances that
• (If your appliance is marked with the following may pollute the environment. When you eventually discard
text applies:) the appliance, remove the rechargeable battery and hand it
The built-in rechargeable (NiCd) battery contains in separately at an official collection point.
substances which may pollute the environment. Note: you can also take the appliance to a Philips Service
When you discard your appliance in due course, Centre, where staff will be happy to help you.
please ensure that the battery is kept separate from
normal household refuse and disposed of at an How to remove the built-in rechargeable battery when
officially assigned collection point. Please refer to the appliance is disposed of
section "Protecting the environment". - First make sure that the appliance has been disconnected
from the mains supply (fig. 21).
- Undo the screw of the base plate at the back of the
General description (fig. 1) appliance (fig. 22).
A
Comb attachment (adjustable/detachable to set the - Pull the printed circuit board holder out of the appliance
beard length) (fig. 23).
B
Beard length indication window - Insert a screwdriver into the small slot in the printed circuit
C
"Zoom ring" for beard length control (rotate) board (fig. 24).
D Cutting unit - Push the screwdriver down until part of the printed circuit
E
Precision trimmer board breaks off.
To switch on: slide the trimmer upwards - Undo the two snap connections between the upper and
To switch off: slide the trimmer downwards lower part of the printed circuit board holder by means of a
F
On/Off switch screwdriver (fig. 25).
On: slide the switch upwards - Break off the small hooks that keep the printed circuit
Off: slide the switch downwards board in place (fig. 26).
G
Pilot light "Charging" - Now you can remove the printed circuit board from the
H
Brush plastic holder (fig. 27).
I
Mains cord - Separate the rechargeable battery from the printed circuit
J Pouch board by means of a screwdriver (fig. 28).
- Dispose of the rechargeable battery and the printed circuit
Charging board in an environmentally safe way by handing them in
• Charge (and use) the appliance at temperatures at an official collection point.
between +15 °C and +35 °C (+60 °F and +95 °F
respectively). Do not connect the appliance to the mains supply after
• Type HQ T388 comes in two versions: with NiMH the rechargeable battery has been removed!
battery and with NiCd battery. Please check the
symbol on the typeplate of the appliance first.
- The battery will be fully charged in approximately
12 h (NiMH version) and 10 h (NiCd version).
- A full charge provides you with an average of 60 minutes
(NiMh version) and 40 minutes (NiCd version) of use.
There is no danger if your trimmer remains connected to
the mains. But in order to guarantee the longest possible
working life of the battery do not charge for more than
24 hours.
The appliance only gets charged if you:
1. put the On/Off switch in the "Off" position (fig. 2),
2. insert the small plug firmly into the trimmer (fig. 3), and
3. insert the mains plug into the wall socket (100-240 V AC)
(fig. 4). The pilot light will come on to indicate that the
battery is being charged (fig. 5).
Directly from the mains supply
You can also use the trimmer directly from the mains
supply (fig. 6).
If the battery is completely empty the trimmer might not start
immediately. In this case switch off, charge for one minute
and switch on again.
Note:
• In order to guarantee the longest possible working life of
the battery:
- Do not charge for more than 24 hours.
- Do not keep the cord permanently plugged in.
- A weaker motor sound indicates that the rechargeable
battery will be empty soon. Only plug in the cord when
you hear this weaker sound.
- Discharge the battery completely once a year by letting
the motor run until it stops.
• If you haven't used the appliance for a long period, charge
it before use.
How to use the trimmer
Before trimming, always comb your beard and/or
moustache, using a fine comb.
• Beard trimming: with comb attachment
- Initially use the position for maximum beard length: set the
comb attachment to position 9, by turning the "zoom ring"
(fig. 7).
- For most effective cutting, move the trimmer against the
direction of beard growth (fig. 8).
- Choose the required beard length (fig. 9). There are
9 positions:
Position Resulting beard
setting of zoom ring length (in mm)
9 18.0
8 15.0
7 12.0
6 9.5
5 7.5
4 5.5
3 4.0
2 2.5
1 1.5
• Trimming the unique "Stubble look"
- Your appliance comes equipped with a unique comb
that has a small slot between the two rows of teeth
(see fig. 10). This enables you to cut the hairs of the
beard to a length of only 1.5 mm. The result is a very
short stubble beard. To obtain the shortest possible look,
the trimmer can be used without the comb in order to
reach a stubble length of 0.8 mm.
• Clipping single hairs, trimming and shaping of full
beards: without comb attachment
- Pull the comb from the appliance (fig. 11).
- Make well-controlled movements. Touch the hair lightly
with the trimmer (fig. 12).
polski •
•
•
•
•
•
•
•
• •
•
•
•
•
A
B
C
D
E
F
G
H
I
J
•
•
•
•
•
•
1
D
•
E
A
•
C
H
•
B
F
•
•
G
•
•
•
J
•
•
I
• (Esli Vaπa maπinka dlä podravnivaniä borody i usov
imeet markirovku , vypolnäjte
NIMH
• (Esli Vaπa maπinka dlä striΩki borody imeet
markirovku , vypolnäjte sleduüwie ukazaniä:)
2 3 4
9
8
7
6
5
4
3
2
1
5 6
A
B
C
D
E
7 8 9
9
8 F
7
6
G
H
I
J
10 11 12
•
°C
• HQ T388
13 14 15
NiMH
NiCd
NiMH
NiCd
16 17 18
1
2
19 20 21
2
CLICK
1
1
22 23 24
•
1
2
25 26 27
1
2
•
1
28
2
1
1
•
•
Beard Trimmer
Tondeuse à barbe
•
•
Vysokotohnyj podravnivatel´
•
•
u
Primehanie: Vy moΩete otnesti maπinku v servisnyj
centr firmy "Filips", gde Vam budut rady v qtom pomoh´.
Off
T 3 88
4203 000 45261