Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for PCI Ultra 133
- Page 1 PCI Ultra 133 RAID Card User's Manual...
-
Page 2: Table Of Contents
Table of Contents »Introduction • Features « Package Content * System Requirement • Hardware Installation P. 2 » Software Installation * Appendix P. 3 « Creating Striped Sets (RAID 0) P. 3 « Creating Mirrored Sets (RAID 1) « Deleting RAID Sets P. -
Page 3: Introduction
, Introduction The Card is a single-chip solution for a PCI to ATA controller. It accepts host commands through the PCI bus, processes them and transfers data between the host and ATA devices. It can be used to control two independent ATA channels: primary and secondary. -
Page 4: Hardware Installation
• Motherboards have one PCI interface one slot. • User 5 1/4 storage Device. 2. Hardware Installation • Power off computer. • Insert Card in PCI slot. • Connect 1-4 device to board. • Power computer on. 3. Software Installation... -
Page 5: Appendix
7. Insert Drivers disk in floppy disk drive. 8. Click on Have Disk. 9. Click on Browse. 10.Find disk (normally A:/), Select SiI680R.inf. 11.Click on Open. 12.ClickOK. 13.Select SII PCI-0680 Ultra 133 DMA IDE Controller. 14.ClickOK. 15.Close Window. 16.Reboot computer. 4. Appendix Creating Striped Sets (RAID 0) 1. - Page 6 4. Press F2 to create a RAID set. The following Screen appears: Primary Channel: Drive Number: 0 Manufacturer Model 19541 MB Drive Number: 1 Manufacturer Model 19541 MB Secondary Channel: Drive Number: 2 Manufacturer Model 19541 MB Drive Number: 3 Manufacturer Model 19541 MB Set: 1 <0>...
-
Page 7: Creating Mirrored Sets (Raid 1)
Drive Number: 1 Manufacturer Model 19541 MB Secondary Channel: Drive Number: 2 Manufacturer Model 19541 MB Drive Number: 3 Manufacturer Model 19541 MB Set: 1<0,2> CMD RAIDO 39081MB S e t : 2 < l > Manufacturer Model 19541MB Set:3<3> Manufacturer Model 19541MB Press Fl to dissolve RAID set... -
Page 8: Deleting Raid Sets
Drive and destination drive should be from different channels. After entering the source drive (for example, enter 1), the following screen appears: Enter the second drive number (destination drive) in RAID 1 set: 4. Enter the second drive (for example, enter 3). The following screen appears: Do you want to copy from the source to destination drive? (Y/N) NOTE: In the Technical Demonstration Release, enter N. -
Page 9: Creating A Mirrored-Striped Set (Raid 0+1 To Raid 10)
Set: 1 <0,2> Manufacturer Model 19541MB S e t : 2 < l > < 3 > CMDRAID1 19541MB Set: 3 <2> Manufacturer Model 1 9 5 4 1 M B Press F! to dissolve RAID set Press F2 to form RAID set Press <ESC>... - Page 10 Press Fl to dissolve RAID set Press F2 to form RAID set Press F3 to form RAIDO+1 set Press <ESC> to exit Your selection? 2. Choose F3 and the following screen appears: Select the chunk size to be used in RAIDO set: 0=lk l=2k 2=4k 3=8k 4=16k 5=32k 6=64k 7=128k 8=256k 9= ,5M Your selection? 3.
- Page 11 Acknowledgements IBM, and OS/2 are registered trademarks of International Business Machines Corporation. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other brand names and trademarks used here are trademarks of their respective owners. Tested To Comply With FCC Standards FOR HOME OR OFFICE USE...
Need help?
Do you have a question about the Ultra 133 and is the answer not in the manual?
Questions and answers