Haier LET32/40T900 Service Manual
Haier LET32/40T900 Service Manual

Haier LET32/40T900 Service Manual

31.5'' & 40'' lcd tv
Table of Contents

Advertisement

31.5"&40" LCD TV
Service
Service
Service
Description

Table of Contents............................................................1

Important Safety Notice...................................................2
Revision List.........................................................3
1. General Specification..................................................4
2. Operating Instructions............................................5
2.1 The Use of Remote Control...................................5
2.2 To Use the Menus...............................................6
2.3 Front Panel Control Knobs..................................33
2.4 How to Connect................................................36
3. Input/Output Specification.......................................40
4. Mechanical Instructions.........................................42
5. Repair Flow Chart .............................................49
6. PCB Layout ......................................................56
6.1 Main Board.......................................................56
6.2 Power Board.....................................................58
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
TABLE OF CONTENTS
Page
Description
6.3 LED Board.....................................................67
6.4 Key Board.....................................................67
6.5 IR Board.......................................................67
7. Adjustment.....................................................68
7.1 ADC Adjustment............................................68
7.2 FW Upgrade.................................................69
8. Block Diagram........................................................72
9. Wiring Diagram......................................................74
10. Schematic Diagram........................................76
10.1 Main Board..................................................76
10.2 Power Board.................................................90
10.3 LED Board.................................................103
10.4 Key Board...............................................104
10.5 IR Board...................................................105

SAFETY NOTICE

1
Haier LET32/40T900
Horizontal Frequency
31~67 KHz
Page

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LET32/40T900 and is the answer not in the manual?

Questions and answers

Summary of Contents for Haier LET32/40T900

  • Page 1 31.5″&40″ LCD TV Haier LET32/40T900 Service Service Service Horizontal Frequency 31~67 KHz TABLE OF CONTENTS Description Page Description Page 6.3 LED Board…...…………………..……..………..67 Table of Contents..……........…..1 6.4 Key Board………………………..……..………..67 Important Safety Notice........……..2 6.5 IR Board…………………………..……….……..67 Revision List…………………………………………………3 7. Adjustment……………….……….…………...………68 1. General Specification.........………..4 7.1 ADC Adjustment……………………..……...………68...
  • Page 2: Important Safety Notice

    Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Haier Company Equipment. The service procedures recommended by Haier and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose.
  • Page 3: Revision List

    Revision List Version Release Date Revision Instructions Customer Model Model E32BA2NBACH72N LET32T900 E32BA2NBACH7NN Apr.28,2011 Initial release LET40T900 E40B82NBACH62N Add new power board: 715G4654P01W21003M Update: Aug.26,2011 LET32T900 E32B22NCACH7NN Repair Flow Chart PCB Layout Schematic Diagram Aug.26,2011 Add new model LET40T900 E40B82NCACH6NN...
  • Page 4: General Specification

    1. General Specification Note • This model complies with the specifications listed below. • Designs and specifications are subject to change without notice. • This model may not be compatible with features and/or specifications that may be added in the future. Model No.
  • Page 5: Operating Instructions

    2. Operating Instructions 2.1 The Use of Remote Control...
  • Page 6: To Use The Menus

    2.2 To Use the Menus...
  • Page 30 Press the “menu” key and the number key “XXXXXX” to enter hotel mode. “XXXXXX” is the password request by Customer (6 numbers). ************ HAIER password is Menu + 100108 ************* 2. Starting the hotel mode If you want to turn on the hotel mode, please press the“>”key or the“<”key on the remote control to set the hotel mode on!...
  • Page 31 5) Remote control operation [RC BUTTON] Option “RESPOND”,“NORESPOND”or“LIMITED” Default RESPOND RESPOND:The remote control is enabled. ・ NO RESPOND:The remote control is disabled. The POWER key is also ・ Function disabled. LIMITED:only (POWER, VOLUME ( / ), CHANNEL ( / ) , ATV,DTV ∧...
  • Page 32 10) Input fixed [INPUT MODE FIXED] Option “VARIABLE”“FIXED”,“AC CTRL”or“AC/RC CTRL” Default VARIABLE 1. “VARIABLE”: The input source can be changed when power on. 2. “FIXED”: The input source will be changed to the “INPUT MODE START” setting value when power on. Function 3.
  • Page 33: Front Panel Control Knobs

    2.3 Front Panel Control Knobs...
  • Page 34 • Do not place the remote control on a wet object. • Do not place the remote control under the direct sunlight or near heat sources. Remove the battery from remote control handset when it is not to be used for a long period. Otherwise it could cause...
  • Page 35 corrosion or battery leakage and may result in physical injury and/or property damage including fire. PRECAUTIONS To obtain the best performance from your remote control, please consider the following: • Ensure there is no obstruction between remote control and TV set. •...
  • Page 36: How To Connect

    2.4 How to Connect...
  • Page 40: Input/Output Specification

    3. Input/Output Specification 3.1 Input Signal Connector D-SUB Pin No. Description Pin No. Description Red Video +5V(supply from PC) Green Video Sync Ground Blue Video UART-RX UART-TX Bi-directional data(SDA) Ground H-Sync Red Ground V-Sync(vclk) Green Ground Data clock (SCL) Blue Ground HDMI Pin No.
  • Page 41 Full Scart Pin No. Description Pin No. Description Audio output B(right) Comms data 1 Audio input B(right) Ground(red) Audio output A(left) Ground(blanking) Ground(audio) Red input or Chroma Ground(blue) RGB switching control Audio input A(left) Ground(video input&output) Blue input Ground(RGB switching control) Function select Video output(composite) Ground(green)
  • Page 42: Mechanical Instructions

    4. Mechanical Instructions LET32T900 Step1. Remove the STAND BASE. Step2. Remove the REAR COVER.
  • Page 43 Step3. Remove the BKT. Step4. Separate the AC COVER and SHIELD.
  • Page 44 Step5. Remove the MAIN BOARD, POWER BOARD and SPEAKERS. Step6. Remove the AC SOCKET and BKT and separate the BEZEL and PANEL.
  • Page 45 Step7. Remove the LED BAORD, IR BOARD and KEY BOARD.
  • Page 46 LET40T900 Step1. Remove the STAND BASE. Step2. Remove the REAR COVER.
  • Page 47 Step3. Remove the BKT, AC COVER, MAIN BOARD and POWER BOARD. Step4. Remove the BKT and separate the BEZEL and PANEL.
  • Page 48 Step5. Remove the LED BAORD, IR BOARD and KEY BOARD.
  • Page 49: Repair Flow Chart

    5. Repair Flow Chart 1. No power No power (LED “Off”) Check the AC input and Power “On” the power is “ON”? Power board Replace the power board output=5/5.2V? Check the IR board and LED Replace the IR board Replace the main board...
  • Page 50 2. Can’t start Can’t start(LED red) Replace the power board Power board output=24V? Replace the key board Check the power key is under control? Replace the IR board Check the IR receiver is normal? Replace the main board Replace the Power board...
  • Page 51 3. Abnormal Display Abnormal Display Reset the source Check the source Enter factory mode to do “EEPROM initial”&“Reset” Replace the main board Check the main board Check the LVDS cable Replace the LVDS cable Check the panel Replace the panel...
  • Page 52 4. No display No display (LED white) Check TV is under control and power Replace the main board on/off by remote control and power key? Check the backlight is “On”? Check the LVDS cable Check the B/L signal is available? Reinsert or replace the LVDS cable Replace main board...
  • Page 53 5. Sound problem No sound or sound abnormal Check the audio source connection and the TV system are correct? Reinsert the audio cable or change the TV system Check the TV is muted, adjust the volume or enter the menu to reset? Enter factory mode to do “Reset”...
  • Page 54 6. Remote control malfunction Remote Control malfunction Check the remote control battery is Replace the battery not properly placed or no power? Use the other remote controls Replace the remote control Whether the IR board is Replace the IR board abnormal? Replace the main board...
  • Page 55 7. OSD is unstable or can’t work normally OSD is unstable or can’t work normally Reconnect the key board Key board connected properly? Replace the button function Buttons are OK? Replace the key board Key board is OK? Enter factory mode to do “Reset” Replace the main board...
  • Page 56: Pcb Layout

    6. PCB Layout 6.1 Main Board 715G4589M01000004K...
  • Page 58: Power Board

    6.2 Power Board LET32T900 715G4500P01W30003S...
  • Page 61 LET32T900 715G4654P01W21003M...
  • Page 64 LET40T900 715G4581P01W30003H...
  • Page 67: Led Board

    6.3 LED Board 715G4733T0C000004M 6.4 Key Board 715G4749K0D000004M 6.5 IR Board 715G4724R0C000004S...
  • Page 68: Adjustment

    7. Adjustment 7.1 ADC Adiustment Introduction of adjust item: They only need adjust WB(Ypbpr/VGA’s Normal/Warm/Cool). Content of WB Adjustment 1. Enter into the factory mode:(same as the above-mentioned). 2. Take an example of adjust Ypbpr_Normal: a. Select item”Source”: Ypbpr and item “Color Temp”: Normal. b.
  • Page 69: Fw Upgrade

    7.2 FW Upgrade Step 1: Ready for F/W upgrade 1.1 Change the “.pkg” format software file name to “upgrade.pkg”, eg: After change: 1.1 Prepare a USB memory (The file system of USB memory must be FAT16 or FAT 32). 1.2 Copy the file (upgrade.pkg) from your computer to the U-disk root path, and remove the USB port from computer’s USB port! Note: 1).
  • Page 70 2.5 Press “OK” by RC to start programming. During the update process, forbid to unplug the U-disk and AC power cable. 2.6 After finishing the update, restart TV. Step 3: Check the F/W version and reset to default. 3.1 Turn on TV, press “MENU”+“1”+“9”+“9”+“9” key rapidly on the Remote control to enter the factory mode (Figure 3.1).
  • Page 71 3.2 Check the F/W version on the second row of the factory mode info. If F/W version is incorrect, please check the version of F/W in your USB memory, else let’s go to Step 3.3. Figure 3.2 3.3 If F/W version is correct, press ‘BACK’ Key on the Remote control to be off factory mode. BACK Figure 3.3 3.4 Do factory reset in user menu, and restart TV.
  • Page 72: Block Diagram

    8. Block Diagram ENV57U03D5F /TDTK-G931 IF(+/-) for PAL/SECAM K4B1G1646E-HCH9 1Gb MX25L6445(NC) HY27US08561A-TPCB 256Mb RF Tuner for IF(+/-) for DVB C/T/ T2 PAL/DVB-C/T/T2 DDRIII/1 Gb/ 1333 MHz NOR FLASH 8 MB NAND FLASH 256 MB IF(+/-) for DVB C/T MN88471 DVB-C/T/T2 DEMOD(NC) I2C for No DVB-T2 I2C for With DVB-T2 LCD PANEL T-CON...
  • Page 73 POWER SWITCH AUDIO AMP PWR_16V/24V AUDIO _PVDD PWR_16V/24V AON4421(NC) STA339BWTR 1000 mA SOUND WOOFER STANDBY STA515W(NC) LCD PANEL T-CON POWER SWITCH +12/5V LVDS_VDD +12V AON4421 DFN LCD PANEL +5V_STB PANEL_VCC_ON/OFF MAIN CHIP BUCK CONVERTER +5V_STB TPS54319RTE DV11 & VCCK VCCK MT5366 STB_PWR5V 2250 mA...
  • Page 74: Wiring Diagram

    9. Wiring Diagram Panel LET32T900 Panel 13 Pin 095G801313D-34 095G179J30N--1 Harness CN9303 FFC Cable 30 Pin CN409 CN9304 CN701 MT5366CHOU/B (U401) Scaler IC Power Board CN402 AC IN CN9901 CN601 7 Pin Key Board Speaker Speaker IR Board CN0101 CN0201 CN0301 4 Pin LED Board...
  • Page 75 LET40T900 Panel Panel 12 Pin 095G801413D-55 095G801851X574 CN8101 Harness LVDS Cable 40 Pin CN408 CN9401 CN701 MT5366CHOU/B (U401) Scaler IC Power Board CN402 AC IN CN9901 CN601 7 Pin Key Board Speaker Speaker IR Board CN0101 CN0201 CN0301 4 Pin LED Board...
  • Page 76: Schematic Diagram

    10. Schematic Diagram 10.1 Main Board 715G4589M01000004K 4) Power-1 EU MT5365 - 2 LAYERS for small size 193X225 INVERTER_ON_OFF DV33SB DV33SB 6,7,9,11,13,14 +24V_16V Normal:High +24V_16V +12V/5V +12V/5V +5V_STB +5V_SW +5V_STB Standby:Low +5V_STB 5,7,14 STB_PWR5V STB_PWR5V 9 DC POWER INPUT VCCK VCCK BRIGHT_ADJ STB_PWR5V...
  • Page 77 5) Power-2 PANEL_VCC +12V/5V +12V/5V +12V/5V +5V_STB Panel VCC=12V or 5V +5V_STB 4,7,14 +5V_SW +5V_SW 4,7,10,11,13,14,15 +5V_TUNER R754 +5V_TUNER 17 DV33 0R05 DV33 4,6,7,8,9,13,14,15,16 AV33 AV33 4,6,13 +5V_STB DV33SB DV33SB DV33SB 6,7,9,11,13,14 Q751 +5V_STB AV12 AV12 6,15 PANEL_VCC U751 R752 PANEL_VCC 14 G903T63UF NC/0R05 4A 1/4W...
  • Page 78 6) MT5366 3.3V IO Power ( Close to MT5365 ) OPWRSB 4,5,7,8,9,10,11,12,13,14,15,16,17 OPWRSB Analog Normal Power DV33 4,5,7,8,9,13,14,15,16 DV33 DV33 DV33SB 5,7,9,11,13,14 DV33SB MRF_AGC R4169 RF_AGC_H AV33 4,13 AV33 10K 1/16W 5% AV12 AV33 AV12 5,15 AV12 C4173 VCCK VCCK 47N16V R4157 AVDD12_PLL...
  • Page 79 7) Flash/Uart/RS232/IR/JTAG +5V_SW +5V_SW 4,5,10,11,13,14,15 NAND Flash 32MB 8MB NOR Flash for boot code. Reset IC +5V_STB 27MHz CRYSTAL +5V_STB 4,5,14 DV33 DV33 4,5,6,8,9,13,14,15,16 +5V_STB DV33SB DV33SB 5,6,9,11,13,14 DV33 DV33SB DV33 DV33 DV33 +12V/5V U4051 4,5,6,8,9,10,11,12,13,14,15,16,17 DV33 For AUO Panel X4150 NC28 OXTALI...
  • Page 80 8) AUD MUX/LINE AMP Audio MUX Input +12V/5V +12V/5V +24V_16V +24V_16V Audio MUX CTRL AMUX_5V AMUX_5V DV33 DV33 4,5,6,7,9,13,14,15,16 +5V_SW +5V_SW Audio Input select table +5V_SW +5V_SW AMUX_5V GND 4,5,6,7,9,10,11,12,13,14,15,16,17 FB600 U605 VGA_LIN AMUX_12V AIN_CTL1 AIN_CTL0 SCART1_LIN SCART1_RIN 10 OHM R632 R630 Y PBPR_RIN...
  • Page 81 9) Audio Amp/HP Out Main Speak CKT 220R/2000mA FB632 +24V_16V Clos e to AUD_V33 Clos e to U602 220R/2000mA FB633 U602 Pin8 DV33 FB631 AUD_V33 Pin11 AUD_VCC 220R/2000mA R641 4K7 1/16W 5% +24V_16V SMD/0402 +24V_16V C634 C635 C636 C637 +12V/5V C632 C633 +12V/5V...
  • Page 82 10) Scart I/O SCART 1(Full SCART) -- CVBS+SV+RGB+TV OUT CVBS IN D1054 Close to CONNECTOR CVBS OUT FAST BLANKING/SOY AMUX_5V AMUX_5V 4,5,7,11,13,14,15 Full SCART(RGB + Close to IC Close to IC Close to CONNECTOR +5V_SW +5V_SW +5V_SW 4,5,7,11,13,14,15 NC/BAS316 R1009 100R 1/16W 5% CVBS + L/R IN_OUT) 4,5,6,7,8,9,11,12,13,14,15,16,17...
  • Page 83 11) YPBPR/VGA/Side AV Input VGA_5V YPbPr in & SPDIF output NEAR YPBPR CONNECTOR NEAR MT5365 VGA_5V 4,5,7,10,11,14,15 +5V_SW AMUX_5V +5V_SW 4,5,7,10,13,14,15 AMUX_12V AMUX_5V YPbPr R1151 NEAR YPBPR CONNECTOR DV33SB DV33SB 5,6,7,9,13,14 0R05 1/16W SOY 1 DV33 D1150 DV33 5,6,7,9,13,14 C1152 NC/BAS316 4,5,6,7,8,9,10,12,13,14,15,16,17 1.5nF 50V...
  • Page 84 12) DDR3 DRAM DDR3#1 DDRV U402 Damping and Termination for CLK DDRV RDQ0 B_A0 DQL0 4,5,6,7,8,9,10,11,13,14,15,16,17 RDQ1 B_A1 DQL1 RDQ2 B_A2 DQL2 RDQ3 B_A3 Close to MT5365 Close to DRAM DQL3 RDQ4 B_A4 DQL4 RDQ5 B_A5 DQL5 RDQ6 B_A6 RCLK0 R4105 CLK0 DQL6...
  • Page 85 13) HDMI1/HDMI2/HDMI3 Input AV12 ARC (Audio Return Channel) AV12 5,6,15 DV33SB AV33 AV33 DV33 +5V_STB D502 +5V_STB 4,6 FUNCTION TABLE DV33 NEAR IC DV33 4,5,6,7,8,9,14,15,16 FB504 DV33SB DV33SB 5,6,7,9,11,14 BAS316WS ARC_SW +5V_SW INPUT OUTPUT +5V_SW 4,5,7,10,11,14,15 DV33_HDMI VGA_5V R502 AV33 VGA_5V 4,5,7,10,11,14,15 120R/3000mA R503...
  • Page 86 14) LVDS Output/USB PANEL_VCC PANEL_VCC +5V_SW +5V_SW 4,5,7,10,11,13,15 TP402 TP412 DV33SB DV33SB 5,6,7,9,11,13 DV33 DV33 4,5,6,7,8,9,13,15,16 +5V_STB +5V_STB 4,5,7 TP403 TP413 LVDS OUTPUT 4,5,6,7,8,9,10,11,12,13,15,16,17 TP404 TP414 NEAR CN408 TP405 TP415 LVDS_VDD PANEL_VCC LVDS Interface TP406 TP416 FB405 120R/3000mA TP407 TP417 LVDS_VDD CONN FB406...
  • Page 87 15) DVB-C+T_DEMOD MT5135/CI +5V_SW DVB-C/T DEMOD MT5135 X'TAL for MT5135 +5V_SW 4,5,7,10,11,13,14 DV33 DV33 4,5,6,7,8,9,13,14,16 AV12 AV12 4,5,6,7,8,9,10,11,12,13,14,16,17 XTALI C1238 33pF 50V 27MHz X1001 C1239 TS output to Mt5365 (Serial) U1011 33pF 50V XTALO DEMOD_TSCLK DEMOD_TSCLK 6 DEMOD_TSVAL DEMOD_TSVAL 6 DEMOD_TSSY NC DEMOD_TSSY NC 6 DEMOD_TSDATA0...
  • Page 88 16) DVB-C+T+T2_DEMOD MN88471 I2C for MT5135 & Tuner DV33 +5V_SW +5V_SW 4,5,7,10,11,13,14,15 DV33 I2C for Tuner DV33 4,5,6,7,8,9,13,14,15 T2_CLK MT5135_CLK R1370 0R05 1/16W R1373 4,5,6,7,8,9,10,11,12,13,14,15,17 Q1501 T2_DATA R1371 0R05 1/16W MT5135_DATA 4K7 1/16W 5% 2N7002 TUNER_CLK T2_CLK R1501 NC/0R05 1/16W OSCL0 OSCL0 6,7,9...
  • Page 89 17) DVB-T+C+T2 Tuner TUNER +5V_TUNER +5V_TUNER 5 +5V_TUNER 4,5,6,7,8,9,10,11,12,13,14,15,16 +5V_TUNER PANASONIC ENV57U05D8F FB1038 FB1034 TU101 +5V_ANT +5V_VCC ENV57U03D5F NC/120R/600mA 120R/600mA C1302 C1303 +5V_ANT C1321 C1322 100N 16V 10uF 16V Tuner IF output +B activ e ANT +5V_VCC 1N 50V 10uF 16V RF_AGC_T RF-AGC Monitor BT Monitor...
  • Page 90 10.2 Power Board LET32T900 715G4500P01W30003S F9901 FUSE R9901 2.5R 2.4W 430K 1/4W C9912 NR9802 C9901 L9902 C9911 L9901 CN9901 470NF 305V BD9901 470PF 250V 470NF 305V TS10B06G-06-X0 C9902 R9902 430K 1/4W RV9901 12MH 12MH Varistor C9914 C9913 470PF 250V R9903 430K 1/4W HEAT SINK (Q9801 D9802) HS9801...
  • Page 91 B+_LLC BEAD FB9302 R9322 47 OHM 1/4W 2N2 500V 2N2 500V R9302 C9317 C9303 0.1 ohm T9301 47 OHM 1/4W R9301 POWER X'FMR R9305 CN9303 C9313 C9301 R9303 R9304 47 OHM 1/4W 10NF 2200pF630V 100K 1/4W 100K 1/4W 5.2V L9301 D9302 C9302 3.5uH...
  • Page 92 R9801 FB9801 10 OHM +-5% 3WS 1N5408-11 D9801 BEAD C9801 680NF 520V D9802 FB9802 2.5R 2.4W L9801 FMN-1106S BEAD NR9801 270UH 22OHM +-5% 1/8W D9803 R9802 C9802 C9803 C9812 47UF 450V 47UF 450V 47UF 450V RB160M-60TE25 Q9801 2SK4087LS R9803 47OHM +-5% 1/8W R9805 R9806 20K 1/4W...
  • Page 93 B+_LLC BO_DC R9112 2Mohm 1/4W +/-1% D9101 R9113 R9114 RB160M-60TE25 2Mohm 1/4W +/-1% 2Mohm 1/4W +/-1% R9115 2K 1/4W R9116 C9103 10 OHM 1/8W Q9101 1N 50V 2SK4097LS 9.5A/500V D9110 R9117 FMWN-2308 24K 1/8W R9118 R9119 C9104 47OHM +-5% 1/8W 10K 1/8W Vsen 100N 50V...
  • Page 94 ALL NC R9134 15K 1/4W C9126 ZD9105 Q9103 BC857C R9127 1500pF / 250V 10K 1/4W D9107 R9126 MTZJ T-72 1N4148 560K 1/8W ZD9104 C9124 330N 25V BZX55-C9V1 R9129 1K 1/8W Q9105 TH9101 PMBTA45 R9130 2.2K 1/8W R9133 R9128 2.2K OHM 3W 150 OHM 5.2V Protect...
  • Page 95 LET32T900 715G4654P01W21003 BD901 TS10B06G-06-X0 FB902 BEAD D9802 R9330 1N5408-E(Short pin) T9301 47 OHM 1/4W POWER X'FMR D9801 R929 R9331 FMN-1106S 0.1 ohm 47 OHM 1/4W R9325 R9327 L9902 L9801 100K 1/4W 100K 1/4W C9331 C9820 300UH 2200PF 470NF 500V C9803 470PF1KV C9338 D9308...
  • Page 96 V-CON LED-1 V-CON LED-2 V-CON LED-3 V-CON LED-4 LED-S CN8501 R8501 R8502 R8503 R8504 3.3K OHM 3.3K OHM 3.3K OHM 3.3K OHM R8505 R8506 R8507 R8508 Q8501 Q8502 Q8503 Q8504 LED-1 PO320AL PO320AL PO320AL PO320AL LED-2 100OHM 1/8W 100OHM 1/8W 100OHM 1/8W 100OHM 1/8W IC8504...
  • Page 97 LET40T900 715G4581P01W30003H F9901 FUSE R9901 BD9901 330K 1/4W C9912 C9911 KBJ1008G-F CN9901 220PF C9901 L9902 330K 1/4W C9902 L9901 470NF 275V R9902 470NF 275V RV9901 C9913 R9903 C9914 330K 1/4W 220PF HEAT SINK (Q9801,D9802) HEAT SINK (BD9901) HS9801 HS9901 HEAT SINK (D9302) FB9904 BEAD HS9301 FB9803...
  • Page 98 4.7 OHM 1W R9301 BEAD FB9302 R9302 C9303 T9301 47 OHM 1/4W POWER X'FMR R9305 C9313 C9301 R9303 R9304 47 OHM 1/4W 2N2 500V Coil 10NF 2N2 500V 100K 1/4W 100K 1/4W L9301 5.2V D9302 C9302 SBT15006JST 2N2 500V R9306 R9307 100K 1/4W 100K 1/4W...
  • Page 99 NR9801 FB9801 R9801 10 OHM +-5% 3WS 1N5408-11 D9801 BEAD C9801 D9802 FB9802 680NF L9801 FMN-1106S BEAD NTCR 200UH 22OHM +-5% 1/8W RB160M-60TE25 R9802 D9803 C9802 C9803 47UF 450V 47UF 450V Q9801 2SK4087LS R9804 R9803 680K OHM +-1% 1/4W 47OHM +-5% 1/8W R9805 R9806 20K 1/4W...
  • Page 100 D9204 R9214 2Mohm 1/4W +/-1% D9202 L9201 Coil FMWN-2308 2M 1% 1/4W T9201 R9215 R9216 R9217 RB160M-60TE25 Vsen C9209 2M 1% 1/4W 10 OHM 1/8W Q9201 C9202 C9224 C9206 R9202 R9201 150UF 35V 100UF 35V 1N 50V 2SK4101FS-V 5.6K 1/4W 5.6K 1/4W C9201 100N 50V...
  • Page 101 R9115 R9116 0.1 ohm C9101 D9103 10NF R9117 R9118 R9119 RB160M-60TE25 Vsen C9103 10 OHM 1/8W Q9102 1N 50V 2SK4097LS 9.5A/500V R9120 D9101 R9121 R9122 57V~77V T9101 C9104 47OHM +-5% 1/8W 10K 1/8W Vsen 100N 50V SF35G D9104 C9106 120UF 160V RB160M-60TE25 Q9103 2SK4097LS 9.5A/500V...
  • Page 102 LED1 LED2 LED3 LED4 LED5 LED6 Q8101 Q8102 Q8103 Q8104 Q8105 Q8106 R8111 R8112 R8113 R8114 R8115 R8116 22 OHM 1/8W 22 OHM 1/8W 22 OHM 1/8W 22 OHM 1/8W AO4828L AO4828L AO4828L AO4828L R8101 R8102 R8103 R8104 R8130 R8106 5.1 OHM 1/4W 5.1 OHM 1/4W 5.1 OHM 1/4W...
  • Page 103 10.3 LED Board 715G4733T0C000004M DV33SB R0301 51OHM 1/16W +/-5% L0301 L302 L303 CN0301 DV33SB R0302 NC/1K LED_G LED_R 81G 15W 1 EL Q0301 BC847C CONN R0303 1K1/16W...
  • Page 104: Key Board

    10.4 Key Board 715G4749K0D000004M 3.3V CN0101 Key 1 Key 2 R0110 0.05R SM_SCL SM_SDA C0105 R0111 0.05R U0102 100N16V CONN CIN_01 GPIO_07 CIN1 GPIO7 CIN_02 3.3V CIN2 INT# CIN_03 SM_SDA CIN3 CIN_04 SM_SCL CIN4 SCLK CIN_07 GPIO_09 CIN7 GPIO9 CIN_09 CIN9 DVCC Key 1...
  • Page 105: Ir Board

    10.5 IR Board 715G4724R0C000004S +5V_SW U0202 LIGHT_SENSOR VOUT C0201 ZD0202 NC/1UF 10V NC/UDZSNP3.3B +5V_SW DV33SB CONN DV33SB LIGHT_SENSOR CN0201 C0205 100N16V R0209 R0208 220R 1/16W IRM-3638TF16 2.7K 1/16W U0201...

This manual is also suitable for:

Let32t900Let40t900

Table of Contents