Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Dome DMS01
-
Page 1: User Manual
Always Connected. Always Covered. Siren DMS01 User Manual... -
Page 2: Preface
Preface As this is the full User Manual, a working knowledge of Z-Wave automation terminology and concepts will be assumed. If you are a basic user, please visit www.domeha.com for instructions. This manual will provide in-depth techni- cal information about the Siren, especially in regards to its compliance to the Z-Wave standard (such as compatible Command Classes, Association Group ca- pabilities, special features, and other information) that will help you maximize the utility of this product in your system. -
Page 3: Table Of Contents
Table of Contents Preface ..........................2 Description & Features ..................... 4 Specifications ........................5 Physical Characteristics ....................6 Inclusion & Exclusion ......................7 Factory Reset & Misc. Functions ..................8 Physical Installation ......................9 LED Behavior ........................10 Compatible Command Classes ..................11 Configuration Parameters ..................... -
Page 4: Description & Features
Description & Features The Dome Siren is a battery powered Z-Wave Plus device that alerts the user to events detected by the connected Z-Wave Controller using an audible alarm. In addition to a DECIBEL dB audible alarm for critical events, the Siren has a... -
Page 5: Specifications
Specifications Technical Specifications Radio protocol Z-Wave(500 series) Power supply 2x CR123 3.0V battery Power Consumption Working current 35mA Operating temperature 32—104 °F (0—40 °C) Radio frequency 908.4 MHz US Range Up to 150’ depending on environment Dimensions (L x W x H) Ø2.75”... -
Page 6: Physical Characteristics
Physical Characteristics MAIN BODY BATTERY TABS BATTERIES BACK COVER Figure 1 - Exploded View CONNECT BUTTON LED RING SPEAKER Figure 2 - Showing individual parts A. Inside the Siren and B. Underneath the Siren. Siren Advanced User Manual Page 6 Physical Characteristics... -
Page 7: Inclusion & Exclusion
Inclusion & Exclusion Inclusion Follow the instructions for your Z-Wave Certified Conto enter inclusion mode. When prompted by the controller: 1. The Siren should be within 10’ of your Z-Wave controller for the inclusion process. After successful pairing, the device can be brought to the desired lo- cation. -
Page 8: Factory Reset & Misc. Functions
Factory Reset & Misc. Functions Resetting the Siren If needed, the Siren can be reset locally by following these steps. Only do this when your Z-Wave controller is disconnected or otherwise unreachable. Beware that resetting your device will disconnect it from the system: 1. -
Page 9: Physical Installation
Physical Installation The device should already be included in your Z-Wave system before continuing further. Study the Pre-Installation Checklist below for a broad overview of in- stallation options and other notes to bear in mind . Pre-Installation Checklist 9 The Siren can be mounted on a wall or placed on shelf or tabletop 9 The Siren is loud enough to be audible from inside a drawer 9 The BACK COVER twists CLOCKWISE to be removed 9 The Siren should be included in your Z-Wave System prior to installation... -
Page 10: Led Behavior
LED Behavior Color Behavior This happens when… …the device powers on, but is not yet included in a Blink 5 times in 1 second Z-Wave Network. …the CONNECT BUTTON is pushed 3 times, either Blink 5 times in 500ms resulting in the Siren sending its NodeInfo, or being included or excluded from a Z-Wave network. -
Page 11: Compatible Command Classes
Compatible Command Classes Command Class Notes Device Reset Locally V1 (5A) Powerlevel V1 (73) Battery V1(80) Association Group Information V1 (59) Z-Wave Plus Info V2 (5E) Returned Value: 01 07 00 0F 00 0F 00 Z-Wave Plus Version: 01 Role Type: 07 (Slave Sleeping Listening) Node Type: 00 (Z-Wave Plus Node) - Page 12 Command Class Notes The Siren sends a Notification Report whenever it is turned on, and an- other report when the sound is turned off (either by the user, or by timing out; see Configuration Parameters 2 and 3.) The Sequence Byte is used to help the Controller keep track of multiple siren events—if a chime is sounded while another chime is active, the sequence numbers will incre- ment with each event, resetting back to 01 when no chime events are...
-
Page 13: Configuration Parameters
Configuration Parameters Param Default Size Name Available Settings Setting This parameter sets the volume of the Siren (primary) sound. There are three possible volume levels available. (Low Volume) (Medium Primary Notification Volume Level (Medium Volume) Volume) (High Volume) This parameter defines the length of the Alarm/primary notification. (30 Seconds) (1 Minute) Primary Notification Length... - Page 14 Param Default Size Name Available Settings Setting If Parameter 7 is set to 02, the Siren will play a secondary chime sound instead of the main alarm. The Siren offers ten different sounds to use as the Chime (secondary) notification. This parameter sets the Chime (secondary) notification sound.
-
Page 15: Troubleshooting
To boost your Z-Wave network coverage, add a few non-battery powered Z-Wave devices between the controller and the furthest device, like the Dome On/Off Plug or Water Main Shut-Off. You can even purchase dedicated Z-Wave extenders from 3rd party manufacturers. -
Page 16: Warranty & Support
If you believe the product is defective, has a missing or broken 1153 Timber Dr., Elgin, IL 60123 part or are having difficulty with it please contact Dome as list- ed above for a quick and efficient solution to the problem.