Control 4 Multi Tuner V2 Installation And Setup Manual

Multi Tuner V2
Installation and Setup Guide
Supported Models
• C4-TUN2-E-B Multi Tuner V2
• C4-XMOD Optional XM Module (ships separately)
Box Contents
• Control4 Multi Tuner V2
• AC Power Cable
• Multi Tuner V2 Installation and Setup Guide (this document)
Important Safety Instructions
1. Read and keep these instructions.
2. Heed all warnings and follow all instructions for this product in this and other Con-
trol4® documents included with or related to this product.
3. Improper use of this product may result in potential electric shock.
4. Do not use this product near water.
5. Never spill liquid of any kind on this product.
6. Clean this product only with a damp or dry cloth. Do not use liquid cleaners or aerosol
cleaners to clean the product.
7. Install this product according to the manufacturer's instructions.
8. Install this product according to the National Electrical Code ANSI/NFPA 70 and the
prevailing local codes and requirements.
9. This product is designed for IT power systems with phase-to-phase voltage 120V,
240V, or 277V.
10. This product should be operated with the type of power indicated on the marked label.
If you are not sure of the type of power available, consult your Control4 dealer or local
power company.
11. Slots and openings on a cabinet rack, and components used with this product are pro-
vided for ventilation, reliable operation, and protection from overheating of the product.
These slots and openings must not be blocked or covered.
12. This product should never be placed near or over a radiator or heat register, or in a
built-in installation unless proper ventilation is provided.
13. Never push objects of any kind into this product through cabinet slots because they
may touch dangerous voltage points or short out parts that could result in a fire or
electric shock.
14. Only use the attachments and accessories included with this product or recommended
by Control4.
15. Do not allow anything to rest on the power cord. Do not install or place this product
where people will walk on the cord.
16. Do not use extension cords with any products in a Control4 system.
17. If applicable, unplug this product during lightning storms or when unused for long
periods of time.
18. This product must be installed by qualified professionals only.
19. Do not attempt to service this product yourself except as noted in this guide. Opening
or removing covers of internal components may expose you to dangerous voltage
points or other risks.
20. Refer all servicing to qualified service personnel. Servicing is required when the ap-
paratus has been damaged or frayed in any way; for example, a power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into this product, this
product has been exposed to rain or moisture, this product does not operate normally,
or this product has been dropped.
Home Network Requirements
Ensure that your home network solution is in place before starting your system setup. The
multi tuner can be controlled through Ethernet.
Antenna Requirements:
• Ensure that a proper AM/FM antenna is installed before beginning your system setup.
• For XM systems, install the XM antenna before beginning your system setup.
Product Specifications
Feature Description
Tuners Two independent AM/FM tuners. One expansion slot.
AM Antenna Input 300 Ohm twin-lead spring terminals for stripped wire.
Antenna shared between Tuners 1 and 2.
FM Antenna Input 75 Ohm coax female "F" connector. Antenna shared
between Tuners 1 and 2.
XM Antenna Input (available XM Antenna Input. XM Radio has been granted Part II
with C4-XMOD model only) type approval for this receiver.
Outputs L/R line-level Audio Output on RCA connectors per
tuner.
SPDIF Digital Coax per tuner.
FM Performance
Tuning Range 76.0 MHz - 108.0 MHz
Sensitivity (50 ohm) 2.2 mV EMF
AM Suppression 50 dB
Audio Stereo Separation 25 dB
Audio THD (1 Khz) < 0.5%
AM Performance
Tuning Range 149 – 23000 Khz
Sensitivity 38 mV EMF
Audio S/N 56 dB
Audio THD (1 Khz) < 0.5%
THD (1 kHz) 0.7 %
SIgnal-to-Noise Ratio 50 dB
XM Performance (C4-XMOD Depends on XM subscription and your area.
only)
Display 4-line LED backlit LCD
Communications IEEE 802.3 10/100 Ethernet, RJ-45 jack
Power Requirements 115/230 VAC, 60/50 Hz, 5 Watt Maximum, 0.05A
Dimensions H x W x D: 3.5" x 17.0" x 15.9" (89 x 432 x 404 mm)
Weight: C4-TUN2-E-B (with 2 Weight: 9.9 lbs. (4.50 kg)
Shipping Weight: 13.75 lbs. (6.25 kg)
AM/FM tuners only)
WARNING! Do not expose the apparatus to dripping or splashing. Do not place
objects filled with liquids near the apparatus.
AVERTISSEMENT ! N'exposez pas l'appareil à l'égoutture ou à l'éclaboussement. Ne
placez pas les objets remplis de liquides près de l'appareil.
WARNING! Setzen Sie den Apparat nicht Bratenfett oder dem Spritzen aus. Setzen
Sie nicht die Gegenstände, die mit Flüssigkeiten nahe dem Apparat gefüllt werden.
WARNING! To reduce the risk of fire or electrical shock, do not expose this apparatus
to rain or moisture.
AVERTISSEMENT ! Pour réduire le risque du feu ou de choc électrique, n'exposez
pas cet appareil à la pluie ou à l'humidité.
WARNING! Um die Gefahr des Feuers oder des elektrischen Schlages zu verringern,
setzen Sie diesen Apparat nicht Regen oder Feuchtigkeit aus.
IMPORTANT! Using this product in a manner other than outlined in this document
voids your warranty. Further, Control4 is NOT liable for any damage incurred with the
misuse of this product. See "Limited 2 Year Warranty."
IMPORTANT ! Employer ce produit en quelque sorte autre que décrit dans ce docu-
ment vide votre garantie. De plus, Control4 n'est pas responsable d'aucun dommage
encouru avec l'abus de ce produit. Voyez que « a limité la garantie de 2 ans. »
WICHTIG! Das Verwenden dieses Produktes in gewissem Sinne anders als umrissen
in diesem Dokument hebt Ihre Garantie auf. Weiter ist Control4 NICHT für irgendeine
Beschädigung verantwortlich, die mit der Fehlanwendung dieses Produktes genom-
men wird. Sehen Sie, daß „begrenzte eine 2 Jahr-Garantie."
WARNING! This CLASS I apparatus must be connected to an AC mains socket outlet
that has a protective earthing connection (i.e., third-prong ground conductor). DO NOT
DEFEAT THE PROTECTIVE EARTHING CONNECTION!
AVERTISSEMENT ! Cet appareillage de la CLASSE I doit être relié à une sortie de
douille de forces à C.A. qui a un raccordement de mise à la terre protecteur (c.-à-d.,
conducteur rectifié parfourche). NE DÉFAITES PAS LE RACCORDEMENT DE MISE
À LA TERRE PROTECTEUR!
WARNING! Dieser Apparat der KATEGORIE I muss an einen Wechselstrom-
Hauptleitungseinfaßungsanschluß angeschlossen werden, der einen schützenden
Erdunganschluß hat (d.h., Drittzinke geriebenen Leiter). BESIEGEN SIE NICHT DEN
SCHÜTZENDEN ERDUNG-ANSCHLUSS!