Table of Contents
Summary of Contents for Zigen ZIG-POE-AHTX
- Page 1 HDMI/VGA/CVBS Auto-switching HDBaseT transmitter over single CAT5e/6/7 - 100m, IEEE POE Power Options, 4K, Audio, IR, RS232, LAN - WebOS ZIG-POE-AHTX USER MANUAL Ver. 1.0 zigencorp.com Toll Free: 877-650-5252 International: +1 818-654-5252...
-
Page 2: Table Of Contents
Table of Contents Copyright and Trademark Introduction Package Contents Features Specifications Panel Description – Front Side Panel Description – Back Side Connection and Installation Initial Connections Remote Control WebOS Interface RS-232 Commands Warranty 2 ZIG-POE-AHTX USER MANUAL... -
Page 3: Copyright And Trademark
Copyright and Trademarks: All rights reserved by ZIGEN, INC. No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer. Changes are periodically made to the information in this document. -
Page 4: Introduction
Introduction The ZIG-POE-AHTX is a 100-meter (328 feet) HDBaseT transmitter. The AHTX has 3 inputs with auto-switching – HDMI, VGA/Component and Composite. With switchable POE it can be set up to power upstream and downstream HDBaseT transmitters and receivers. The ZIG-POE-AHTX can be used stand-alone as an HDBaseT transmitter, but really shines when paired with the ZIG-POE-RXAV receiver/scaler &... -
Page 5: Specifications
Specifications Video Bandwidth 10.2 GBPS Video Resolutions HDMI – SMPTE Up to 4096x2160P 60fps @ 4:2:0 8-bit VGA – up to 1920x1080x60 [n1] CVBS – Standard 480i/p Color Space RGB, YUV Color Bit Depth 8-bit, 10-bit, 12-bit, 16-bit – 300 MHz Pixel Clock Chroma Subsampling 4:4:4, 4:2:0 - Audio... - Page 6 Dimensions Weight 3 Pounds Certifications FCC, HDBaseT, CE, RoHS, HDCP, HDMI Control/Access Via RJ45 and WebOS for direct control. Can also be accesses and controlled via ZIG-POE-RXAV or ZIG-PS-61 Works With ZIG-POE-RXAV, ZIG-POE-RX70, ZIG-PS61, ZIG-POE-70R 6 ZIG-POE-AHTX USER MANUAL...
-
Page 7: Panel Description - Front Side
ZIG-POE-AHTX Block Diagram zigencorp.com Toll Free: 877-650-5252 International: +1 818-654-5252... - Page 8 – if you remove an active source – and Note: Auto-Switching function [n5] another source is connected then it will switch to the new source immediately. Additionally, as soon as you connect either source, if none are connected, that port will become active immediately. 8 ZIG-POE-AHTX USER MANUAL...
-
Page 9: Panel Description - Back Side
Back Side 1. HDMI Input – Connect HDMI cable here from your source (BlueRay, Computer, etc.) up to 4K UHD. 2. VGA Input – Connect VGA cable here from PC/MAC or use a breakout cable to connect Component, RGBHV, or Y/C. DVD players, STB, etc. 3. - Page 10 HDBaseT device on the network. Telnet and direct HTTP requests are supported. [n7] 11. RS232 (9-pin) port – Bi-directional for local control and remote control (commands relayed via HDBaseT port. Local commands executed locally. 10 ZIG-POE-AHTX USER MANUAL...
-
Page 11: Connection And Installation
Simple Classroom setup with ZIG-POE-RXAV as Receiver zigencorp.com Toll Free: 877-650-5252 International: +1 818-654-5252... -
Page 12: Initial Connections
LAN ports for almost anything you choose and for controlling/setting up the devices, relays, a 4K scaler and IR and RS232 control and functionality. 1. Connect sources to ZIG-POE-AHTX – HDMI, VGA and Composite – with audio if required. -
Page 13: Remote Control
ZIG-POE-AHTX Remote Control Perfect for classrooms when connected to the ZIG-POE-AHTX use the remote to change between HDMI, VGA and CVBS sources. zigencorp.com Toll Free: 877-650-5252 International: +1 818-654-5252... -
Page 14: Webos Interface
WebOS Interface Page Device Name/Notes Status Command Lines EDID Management Firmware/Reset/ Info 14 ZIG-POE-AHTX USER MANUAL... - Page 15 WebOS Status Connections HDMI – Green when HDMI is the source VGA – Green when VGA is the source Audio – Green when audio is present with the VGA signal Local HDBaseT (RXAV in this case) Link – Green when there is an HDBaseT connection ...
- Page 16 Device Name & Notes Device Name – default out of the box is ZIG-POE-AHTX .XXXX (last 4 [n9] digits of the serial number). You should change it if you are using more than 1 device (Change Name below) to whatever you want – ex.
-
Page 17: Rs-232 Commands
Choose File/Upload Firmware – when necessary, this is where you select a new firmware file and upload firmware. Reset POE-AHTX – will reset the ZIG-POE-AHTX remotely. Install Update – when necessary is for installing new software updates to the unit. - Page 18 @rxav-01 rel1 on Set device ‘rxav-01’ relay 1 to ON position Response: @rxav-01 rel1 x Relay 2 on/off @rxav-01 rel2 on Set device ‘rxav-01’ relay 2 to ON position Response: @rxav-01 rel2 x Get Device Status 18 ZIG-POE-AHTX USER MANUAL...
- Page 19 Get device ‘rxav-01’ status Response: @rxav-01 st power x, vol x, bass x, treb x, mute x, relay1 x, relay2 x Display Device Info @rxav-01 man Get device ‘rxav-01’ device information Response: @rxav-01 Zigen Corp, ZIG- POE-RXAV, fw1 ver xx, fw2 ver yy Power on/off @rxav-01 pwr off Set device ‘rxav-01’...
-
Page 20: Warranty
Such specific warranties are available upon request to ZIGEN. ZIGEN makes no other representation of warranty as to fitness for the purpose or merchantability or otherwise in respect of any of the products sold. The liability of ZIGEN with respect to any defective products will be limited to the repair or replacement of such products.