Page 3
Thank you for purchasing JBL VTX Series products Of all the achievements JBL has made over the years, the VTX Series stands as a milestone in the practical application of creative engineering. The next generation in line arrays, VTX heralds a new era in performance, system integration and user friendliness.
VTX A12 | User Manual 1 - SAFETY Before using a JBL VTX Series system, please review the following for important information on safety and protection of your investment. 1.1 SAFETY INSTRUCTIONS 1. Read these instructions 2. Keep these instructions 3.
None of the information presented herein is intended as a representation or warranty on the part of JBL. Anyone making use of this information assumes all liability arising from such use. All information presented herein is based upon materials and practices common to North America and may not directly apply to other countries because of differing material dimensions, specifications, and/or local regulations.
JBL is not responsible for the application of its products for any purpose or the misuse of this information for any pur- pose. Furthermore, JBL is not responsible for the abuse of its products caused by avoiding compliance with inspection and maintenance procedures or any other abuse.
VTX A12 | User Manual 1.6 - SYMBOLS The following set of symbols are used in this document: CAUTION: This symbol gives notice of a potential risk of harm to the individual or the equipment. In- struction marked with this symbol must be strictly followed.
For more information on the accessories, refer to the accessory specification sheets. For more information on usage, refer to the VTX A12 Rigging Manual available at www.jblpro.com. CAUTION: Always use components and accessories specified and approved by JBL Professional. When a cart is used, use caution when moving the cart to avoid injury from tip-over.
3.6 VTX A12 VT GND - GROUND STACK KIT (PRELIMINARY) • Outrigger system for ground stacking VTX A12 • Support for up to 6 x VTX A12 enclosures • 4 x screw jacks are included for adjusting height • Zero-gravity angle set hinge system •...
4.3 - ARRAY LINK JBL Array Link is a mobile companion app that works in con- junction with JBL’s LAC software to assist with deploying JBL VTX Series systems. Array Link uses a QR code sys- tem to transfer all mechanical array information from the main LAC application to a mobile phone.
JBL VTX A12 is a complete tour sound solution for mid- to large-size touring applications and high-end fixed installations. A solution designed from scratch to address the unique challenges of rental companies, FOH engineers and tour sound production crews.
6 - VTX A12 CONNECTIONS The JBL VTX A12 is equipped with two Neutrik NL8 SpeakON connectors. Both NL8 connectors are wired in parallel and can be used as the system input or as a through connection for daisy-chaining multiple cabinets together. The A12 NL8 connectors are installed upside down so that the NL8 locking pin position can be seen from under the array.
LevelMAX™ Limiter Suite and support for linear-phase FIR filters. All VTX A12 processing is done using I-Tech HD internal processing and no other external DSP is required. The Crown amplifiers include a user-adjustable input section for room correction equalization, array size compensation and circuit adjustments.
7.2 - CROWN I-TECH 12000HD When using Crown Audio I-Tech 12000HD amplifiers, up to 3 VTX A12 loudspeakers can be powered per pair of am- plifiers. One Crown I-Tech 12000HD is used for powering the low-frequency section and another for the mid- and high- frequency sections.
45Hz (Fullrange). VTX A12 FL 80: The FL 80 presets have nominally-flat frequency response and are to be used in situations where one or two A12 cabinets are appropriate, such as distributed front fills. With this preset, the acoustical low-frequency re- sponse of the system is set to 80Hz and used when subwoofers are available.
9 - SUBWOOFER OPTIONS VTX A12 presets are designed for a 3:2 minimum cabinet ratio (A12 : VTX S28 or G28 subwoofers). The 3:2 ratio provides sufficient headroom for both the subwoofers and the VTX A12s to reach MAX SPL (the limiters) at the same time, while maintaining a minimum of 10dB SUB to TOP low-frequency contour.
VTX subwoofer to be used with any VTX loudspeaker without needing specific sub- woofer presets for each system and configuration. When the VTX A12 is operated in full range mode with companion subwoofers, some additional delay should be applied to the subwoofers to match the A12.
(box-to-box angles), and the listening distance. JBL factory presets are designed to create a well-balanced tonal starting point for given array conditions. For example, the standard VTX A12 array presets are designed to work optimally with array sizes between 8 - 12 cabinets and equal impact spacing for a flat listening plane. An array with these parameters will generate a flat frequency response in the HF region with a gradual rise in LF energy.
11.1 - ACCESSING LACP LACP filters can be modeled in JBL’s Line Array Calculator and then imported into JBL’s Performance Manager for appli- cation to actual devices. To access LACP within the Line Array Calculator, first create circuit groups by using the included grouping feature.
VTX A12 | User Manual 11.2 - FILTER 1 - ARRAY SIZE COMPENSATION Filter 1 is used to correct for LF/MF buildup when the array size/shape differ from that for which the factory preset was designed. LF adjustments should be applied to all cabinets within the array: therefore, filter 1 is automatically applied globally.
11.6 - EXAMPLE USING LACP This example is for a 12-cabinet VTX A12 array. The standard A12 preset is used with the Array Size Compensation filter set to –3dB to offset LF buildup and achieve a flatter frequency response. As seen from the illustration below, Array Size Compensation is globally applied to all array circuits.
JBL continually engages in research related to product improvement. Some materials, production methods and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current JBL product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated.
Pacific Coast Time in the U.S.A. (800) 8JBLPRO (800.852.5776) (800) 8JBLPRO (800.852.5776) www.JBLservice.com support@jblpro.com Professional Contacts, Outside the USA: Contact the JBL Professional Distributor in your area. A complete list of JBL Professional international distributors is provided at our U.S.A. website: www.jblpro.com...