GEAppliances 47065 Installation Instructions Manual
GEAppliances 47065 Installation Instructions Manual

GEAppliances 47065 Installation Instructions Manual

27" built-in oven

Advertisement

Available languages

Available languages

INSTALLATION INSTRUCTIONS FOR YOUR NEW
Before you begin—Read these instructions completely and carefully.
IMPORTANT—Save these instructions for local inspector's use.
IMPORTANT—OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer—Be sure to leave these instructions with the Consumer.
OWNER—Keep these instructions for future reference.
Note—This appliance must be properly grounded (if applicable).
FOR YOUR SAFETY
• Be sure your oven is installed properly by a
qualified installer or service technician.
• Be sure the oven is securely installed to a
cabinet that is firmly attached to the house
structure.
Weight on the oven door could
potentially cause the oven to tip and result in
injury.
Never allow anyone to climb, sit,
stand, or hang on the oven door.
• Make sure wall coverings, cabinets and
countertops around the oven can withstand
the heat (up to 200
TOOL LIST
• 3/32" Drill Bit
• Electric or Hand Drill
• Flat Blade and Phillips Screwdriver
• Pencil
• Ruler and Straightedge
• Hand Saw or Saber Saw
LOCATION
Cabinet space must be provided to enclose the
recessed part of your built-in oven.
OVEN INSTALLATION— See Figure 1 for all necessary
dimensions. DOUBLE OVEN INSTALLATION— See
Figure 2 for all necessary dimensions. It is best to make a
template to insure accurate cutting.
Place the bottom of the template on a level base line. See
Dimension E in Fig.1 (Single Oven) on page 3, or Fig. 2
(Double Oven) on page 4.
installation, see page 5. See Figure 3 for cutout dimensions
to install a single built-in oven under approved cooktop
models.
Pub. No. 31-10200
SR10313
4053P056-1
229C
27" BUILT-IN OVEN
°
F) generated by the oven.
SINGLE
For under the counter
ELECTRICAL REQUIREMENTS
CAUTION:
to the oven supply line must be shut
STOP!
off while lineconnections are being
made. Failure to do so could result
in serious injury or death.
This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
fuse, having amperage as noted on rating plate. (Rating
plate is located on oven frame.)
We recommend you have the electrical wiring and hookup
of your oven done by a qualified electrician. After installation,
have the electrician show you where your main range
disconnect is located.
Check with your local utilities for electrical codes which
apply in your area. Failure to wire your oven according to
governing codes could result in a hazardous condition. If
there are no local codes, your range must be wired and
fused to meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition.
You can get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical Code
requires that new, but not existing, construction utilize a
four-conductor connection to an electric range. When
installing an electric range in new construction, follow the
instructions
in
FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C. 208Y/120
Volt or 240/120 Volt, 60 Hertz electrical system. If you
connect to aluminum wiring, properly installed connectors
approved for use with aluminum wiring must be used.
1
The electrical power
NEW
CONSTRUCTION
Continued on next page
AND

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 47065 and is the answer not in the manual?

Questions and answers

Summary of Contents for GEAppliances 47065

  • Page 1 INSTALLATION INSTRUCTIONS FOR YOUR NEW 27" BUILT-IN OVEN Before you begin—Read these instructions completely and carefully. IMPORTANT—Save these instructions for local inspector’s use. IMPORTANT—OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer—Be sure to leave these instructions with the Consumer. OWNER—Keep these instructions for future reference.
  • Page 2: Electrical Connection

    ELECTRICAL CONNECTION THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION 1. De-energize oven branch circuit. 2. With oven in front of cabinet opening, connect flexible • When connecting to a three-conductor branch circuit, if conduit to the junction box in such a manner that it will local codes permit, connect the bare oven ground hang down in a natural loop against the left side of the conductor with the crimped neutral, (white), lead to the...
  • Page 3 OPTION 1: IN CABINET INSTALLATION NOTE: Locate an approved junction box in one of the suggested locations, a minimum of 34" above the runners or 5" below the runners. The oven can be installed in a 28 1/8" high cutout by proper use of long shims on bottom runners and proper cabinet top retainer.
  • Page 4 NOTE: Locate an approved junction box in one of the suggested locations, a minimum of 56" above the runners or 5" below the runners. The oven can be installed in a 50 1/8" high cutout by proper use of long shims on bottom runners and proper cabinet top retainer.
  • Page 5 32" MIN. FROM TOP OF CABINET TO TOP OF RUNNERS MUST BE MAINTAINED. NOTE: SEE BUILT-IN OVEN INSTALLATION INSTRUCTIONS FOR COMPLETE INSTALLATION INSTRUCTIONS. MODELS APPROVED FOR UNDER THE COUNTER INSTALLATION: 47065, 47069 JKP15AW, JKP15BW, JKP15WW 47169 JKP18AW, JKP18BW, JKP18WW 47465, 47469...
  • Page 6: Remove The Oven Door

    Your built-in oven is packed with a shipping base pad on OVEN TO CABINET MOUNTING SCREWS the bottom of the unit. The lower front trim is shipped separately and should not be used until you are ready to install the oven with door removed. See Step 2. REMOVE THE OVEN DOOR SIDE TRIM...
  • Page 7 INSTRUCCIONES DE INSTALACION PARA SU NUEVO HORNO INCORPORADO Antes de empezar—Lea estas instrucciones completa y cuidadosamente. IMPORTANTE—Guarde estas instrucciones para el uso del inspector local. IMPORTANTE—OBSERVE TODOS LOS CODIGOS Y ORDENANZAS VIGENTES. Nota al Instalador—Asegúrese de dejar las instrucciones con el Consumidor. Consumidor—Guarde estas instrucciones para referencia futura.
  • Page 8: Conexion Electrica

    CONEXION DE CIRCUITO CONEXION ELECTRICA CONDUCTOR DE TRES RAMAS 1. Desconecte la electricidad que va al circuito multiple • Cuando conecte al circuíto múltiple de 3 alambres, si del horno. los códigos locales lo permiten, conecte el conductor 2. Con el horno frente a la abertura del gabinete, conecte pelado que va a tierra del horno con el alambre de el conducto flexible a la caja de empalme de manera contacto forrado neutral (blanco) al alambre de contacto...
  • Page 9 OPCION 1: INSTALACION EN EL GABINETE NOTA: Coloque una caja de conexión aprobada en uno de los lugares sugeridos; a un mínimo de 48" sobre los soportes o 5" bajo los soportes. Esté seguro que los soportes del horno sean suficientemente sólidos para soportar 150 libras. También, esté seguro que el soporte del horno esté...
  • Page 10 NOTA: Coloque una caja de conexión aprobada en uno de los lugares sugeridos; a un mínimo de 48" sobre los soportes o 5" bajo los soportes. Esté seguro que los soportes del horno sean suficientemente sólidos para soportar 150 libras. También, esté seguro que el soporte del horno esté...
  • Page 11 * SE DEBE MANTENER 32" MIN. DE LA SUPERFICIE DEL GABINETE A LOS SOPORTES NOTE: SEE BUILT-IN OVEN INSTALLATION INSTRUCTIONS FOR COMPLETE INSTALLATION INSTRUCTIONS. MODELOS APROBADOS PARA LA INSTALACION BAJO EL GABINETE 47065, 47069 JKP15AW, JKP15BW, 47169 JKP15WW 47465, 47469...
  • Page 12 Su horno tipo “Built-In” está empacado con una base acolchonada en el fondo de la unidad. La moldura del frente de abajo y las cubiertas de las puntas vienen separadas y no se deben usar hasta que usted esté listo * DEL HORNO A LOS para instalar el horno con la puerta sacada después de TORNILOS DE MON-...

Table of Contents