Zhejiang Sansilou Industrial BECS-129S Manual

Computerized embroidery machine

page of 112

/ 112
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Part I Features________________________________________________________________________ 1

Part II Control Panel and Basic Operations ________________________________________________ 6

2.1 Control Panel ___________________________________________________________________ 6

2.2 Main Screen ___________________________________________________________________ 10

2.3 Definition and Basic Operation of Keys _____________________________________________ 13

2.4 Indicator Light of Main Shaft Stop Position _________________________________________ 17

2.5 Start and Stop Button____________________________________________________________ 17

Part III Basic Knowledge and Operation __________________________________________________ 18

3.1 Work Status, Embroidery Mode and Work Sequence _________________________________ 18

3.2 Inputting Design from USB-Disk and Starting First Embroidery ________________________ 21

3.3 Select Memory Design for Embroidery _____________________________________________ 26

Part IV Setting Parameters _____________________________________________________________ 29

4.1 Parameter Menu________________________________________________________________ 29

4.2 Real Time Rotation and Scaling up/down ___________________________________________ 30

4.3 Setting Repetition Embroidery ____________________________________________________ 34

4.4 Offset Point ____________________________________________________________________ 38

4.5 Cyclic Embroidery ______________________________________________________________ 39

4.6 Work Sequence _________________________________________________________________ 40

4.7 Standard Data Parameter ________________________________________________________ 42

4.8 Standard Trim Parameters _______________________________________________________ 45

4.9 Standard Machine Parameters ____________________________________________________ 47

BECS-129S Singular-head Computerized Embroidery Machine

Index

Table of Contents

Summary of Contents for Zhejiang Sansilou Industrial BECS-129S

Page 1: Table Of Contents
4.3 Setting Repetition Embroidery ____________________________________________________ 34 4.4 Offset Point ____________________________________________________________________ 38 4.5 Cyclic Embroidery ______________________________________________________________ 39 4.6 Work Sequence _________________________________________________________________ 40 4.7 Standard Data Parameter ________________________________________________________ 42 4.8 Standard Trim Parameters _______________________________________________________ 45 4.9 Standard Machine Parameters ____________________________________________________ 47 BECS-129S Singular-head Computerized Embroidery Machine...
Page 2 6.5 Delete USB Disk Design __________________________________________________________ 68 Part VII Memory Design Operation ______________________________________________________ 69 7.1 Enter the Memory Design Operation Menu _________________________________________ 69 7.2 Select Design for Embroidery _____________________________________________________ 70 7.3 Show Memory Design ___________________________________________________________ 72 BECS-129S Singular-head Computerized Embroidery Machine...
Page 3 8.6 Machine Self-Test and Test Machine Parts __________________________________________ 92 8.7 Set Password ___________________________________________________________________ 92 8.8 Set Network Address ____________________________________________________________ 93 8.9 LAN Function Switch____________________________________________________________ 94 8.10 Net Manual Connect ___________________________________________________________ 95 8.11 Set Design Showing-Color _______________________________________________________ 96 Appendix ___________________________________________________________________________ 98 BECS-129S Singular-head Computerized Embroidery Machine...
Page 5: Part I Features
Press the keys to adjust the current rotating speed of the main shaft between 400 rpm and the highest speed, and the current speed value will show in the screen. And the highest rotating speed for flat embroidery is 1000 rpm. BECS-129S Singular-head Computerized Embroidery Machine...
Page 6 With this function, the frame will return to the origin point upon completion of embroidery. 10. Positioning idling The frame can move fast forward or backward to the desired position according to function code or certain stitches to move without embroidering, BECS-129S Singular-head Computerized Embroidery Machine...
Page 7 In case of wrong operations or machine malfunctions, the screen will show words or icons to inform you. 17. Frame protection When the frame has changed its position after power-off during embroidering or after stopping the machine, it will be unable to continue the BECS-129S Singular-head Computerized Embroidery Machine...
Page 8 22. Change UI Language Choose the desired language to suit different customers. You can choose several kinds of language as follows : Chinese , English , Turkish , Spanish BECS-129S Singular-head Computerized Embroidery Machine...
Page 9 Part I Features and Portuguese. 23. Trimming In embroidery the user can choose the automatic trimming according to the function codes or stopping the machine to trim manually. BECS-129S Singular-head Computerized Embroidery Machine...
Page 10: Part Ii Control Panel And Basic Operations
Part II Control and Basic Operations Part II Control Panel and Basic Operations 2.1 Control Panel LCD Panel BECS-129S Singular-head Computerized Embroidery Machine...
Page 11 Part II Control and Basic Operations Start Button Stop Button Emergency Stop Button Keyboard Style 1 BECS-129S Singular-head Computerized Embroidery Machine...
Page 12 Part II Control and Basic Operations Start Button Stop Button Emergency Stop Button Keyboard Style 2 BECS-129S Singular-head Computerized Embroidery Machine...
Page 13 Part II Control and Basic Operations Emergency Stop Button Start Button Stop Button Keyboard Style 3 BECS-129S Singular-head Computerized Embroidery Machine...
Page 14: Main Screen
After that, it’s no longer allowed to select design, input scale and repetition parameters, delete memory-stored designs, clear all designs in the memory, embroider the design range, save origin points, restore frame position, restore default BECS-129S Singular-head Computerized Embroidery Machine...
Page 15 ”: It comes to the running state during embroidery. “ ”: It comes to the stitch skip codes during embroidery. “ ”: It comes to the color change codes during embroidery. “ ”: Embroidery comes to an end. BECS-129S Singular-head Computerized Embroidery Machine...
Page 16 “ ” or deceleration key “ ”. It shows the actual rotation speed during embroidery, like "1000" in the above picture. 3. Stitch count: It counts the stitches since the last clearance of the BECS-129S Singular-head Computerized Embroidery Machine...
Page 17: Definition And Basic Operation Of Keys
— Disk operation This is for all the operations concerning the U disk, including listing designs in USB disk, inputting USB designs into memory, deleting disk designs, outputting design data to USB disk, formatting USB disk, etc. BECS-129S Singular-head Computerized Embroidery Machine...
Page 18 — Switch key for working methods Press this key to switch between “manual color change and startup” (without application of work sequence) and “embroidering in the set work sequence”. When the machine embroiders in the set work sequence, the icon BECS-129S Singular-head Computerized Embroidery Machine...
Page 19 — Exit key Before confirming the all operations, the user can press this key to end operation and return to the upper menu. Keep pressing the key to return to the main screen. BECS-129S Singular-head Computerized Embroidery Machine...
Page 20 10 rpm. — Acceleration key In the main menu, 10 rpm is raised for each time of pressing this key. Keep pressing it, the rotation speed will rise to the set highest speed. The BECS-129S Singular-head Computerized Embroidery Machine...
Page 21: Indicator Light Of Main Shaft Stop Position
Press Stop button: During the embroidery, the working is stopped; at the machine stopping, the machine will return at a single step for 10 stitches and then return continuously while the user keeps pressing the button. BECS-129S Singular-head Computerized Embroidery Machine...
Page 22: Part Iii Basic Knowledge And Operation
In menu operations of this system, the available options are in highlight while the unavailable options are in darkness. 2. Embroidery method and returning for patching The machine has the following embroidery methods: normal embroidery, BECS-129S Singular-head Computerized Embroidery Machine...
Page 23 When the machine stops returning, the user can press the startup button to start patching. If the machine is set as low-speed idling, when the user presses the startup BECS-129S Singular-head Computerized Embroidery Machine...
Page 24 Otherwise the user should set it in the manual operation before embroidery. The user can choose whether to use the work sequence by the key " ". When the work order is effective, it’s displayed in highlight in the main BECS-129S Singular-head Computerized Embroidery Machine...
Page 25: Inputting Design From Usb-Disk And Starting First Embroidery
USB disk into the driver. Then the following screen will be shown: 2) Press " " or the numerical key “ ” to move the cursor the third option “U. Des. Input", and then press the confirmation key" ". BECS-129S Singular-head Computerized Embroidery Machine...
Page 26 4 and the user wants to input a new number 15, he will press the keys “1” and “5”, and then “ ” to confirm. If the number has been used by another design, the confirmation will not be accepted. Otherwise the following BECS-129S Singular-head Computerized Embroidery Machine...
Page 27 6) The system begins the design input, during which the screen shows its progress bar. When the input is finished, the system will ask the user whether to keep inputting design. Select “NO” to cancel the continuous input. After BECS-129S Singular-head Computerized Embroidery Machine...
Page 28 If the user chooses “No”, the system will return to the main menu after he presses the confirmation key “ ”. If he chooses “Yes” by the keys“ ”, the system will enter the parameter menu for parameter setting. BECS-129S Singular-head Computerized Embroidery Machine...
Page 29 Ensure that the main shaft has stopped at the proper position, namely the LED indicator is on. If not, move the main shaft to the position manually. You can press the startup button to start embroidery after the above procedure. BECS-129S Singular-head Computerized Embroidery Machine...
Page 30: Select Memory Design For Embroidery
No.15 exists, it will be set for embroidery and the screen will switch to the parameter settting menu (refer to Part IV). If design No.15 doesn’t exist, the confirmation operation won’t be accepted. Then you need to press “ " to clear and then input/select a new number. BECS-129S Singular-head Computerized Embroidery Machine...
Page 31 "to select the design for embroidery. The keys “ ”are for moving the cursor upwards/downwards. “ ” are for turning the pages. After you press “ ” to confirm the selection, the screen will switch into the menu of parameter setting. BECS-129S Singular-head Computerized Embroidery Machine...
Page 32 " to return to the main screen at any time. ⑹ After selectin g a new design, you can press " " to enter the embroidery confirmation status " ", and then start to embroider. BECS-129S Singular-head Computerized Embroidery Machine...
Page 33: Part Iv Setting Parameters
" ". The first page of the menu is shown as followed: ⑵ You can switch between the two pages of param eter menu by pressing BECS-129S Singular-head Computerized Embroidery Machine...
Page 34: Real Time Rotation And Scaling Up/Down
4.2 Real Time Rotation and Scaling up/down This parameter is to set image scales, rotation direction and angle for embroidery. Operation: ⑴ Under the status “ ”, press “ ” to enter the parameter menu, which is as follows: BECS-129S Singular-head Computerized Embroidery Machine...
Page 35 A cursor "_" appears in the screen. Input numbers to set the X scale 50～200(％). E.g. "1", "2" and "0" are for 120%. Press “ ” and the screen is shown as the followed: BECS-129S Singular-head Computerized Embroidery Machine...
Page 36 ⑶ Input the Ｙ scale where there is a cursor “_”. It is as the followed: Input numbers to set the Y scale 50～200(％). E.g. "1", "6" and "0" are for 160%. Press “ ” and the screen is as follows: BECS-129S Singular-head Computerized Embroidery Machine...
Page 37 ” to select one of the eight directions for the design, e.g. select “ ” and then confirm the selection by pressing“ ”. The screen shows as follows: ⑸ Press“ ” to set the rotation angle, which is marked by a cursor “－”: BECS-129S Singular-head Computerized Embroidery Machine...
Page 38: Setting Repetition Embroidery
The maximum repetition times in each of X and Y direction is 99. So the maximum total repetition is 9801. Operation: BECS-129S Singular-head Computerized Embroidery Machine...
Page 39 “ ” to set the repetition direction as “Y” direction, which is shown in the following picture. ⑶ Press “ ” to set the Repetition Times. Input the number where a cursor “_” is lying. BECS-129S Singular-head Computerized Embroidery Machine...
Page 40 Input the normal repetition times in X direction between 1 and 99. E.g. press “3” and “ ”to set the time of repetition as 3 in X direction. ⑷ Input the new repetition times (1~99) for Y direction. E.g. press “2” and “ ”. BECS-129S Singular-head Computerized Embroidery Machine...
Page 41 Input the new Y-direction interval between -999.9～+999.9( mm). E.g. press the keys "+/-","1" and "0" to set the value as -10 (mm). And then press the key “ ” to confirm. The interface will be displayed as below: BECS-129S Singular-head Computerized Embroidery Machine...
Page 42: Offset Point
After that ,press the start button again, and the frame will return to the offset point (a) as long as the frame is off the point (a), no matter whether auto origin point return has been set or not. Press the start button again to repeat the above actions. BECS-129S Singular-head Computerized Embroidery Machine...
Page 43: Cyclic Embroidery
” to move frame to the offset point and then press “ ” to confirm the setting. The following picture will be shown. 4.5 Cyclic Embroidery Press the key “ ” to set the cyclic embroidery. A square cursor will show where to input: BECS-129S Singular-head Computerized Embroidery Machine...
Page 44: Work Sequence
The work sequence can be only used in the main screen. Press the key “ ” to let the work sequence work. And the icon “ ” will show in the main screen at that time. Operation: BECS-129S Singular-head Computerized Embroidery Machine...
Page 45 "10+" first. Attention: The figure of max needle position can’t be larger than the numbers of machine needles. After the first work sequence is finished, the system is shown as follows: BECS-129S Singular-head Computerized Embroidery Machine...
Page 46: Standard Data Parameter
This is to set the data parameters concerning the flat embroidery. Their options and default values are shown in the appendix. Jump to Trim: (Options: No, 1-7) It is to decide how to deal with the jump stitch codes in the design during BECS-129S Singular-head Computerized Embroidery Machine...
Page 47 The parameter is to set how many stitches the machine will automatically return when the machine detects a thread break and stops automatically in case “Thr. Broken Detect” is set within “3~7”. If the parameter value is 0, BECS-129S Singular-head Computerized Embroidery Machine...
Page 48 If the stitch is too long, the main shaft will reduce its rotation speed. The longer the stitch is, the lower the speed will be. The machine can divide the BECS-129S Singular-head Computerized Embroidery Machine...
Page 49: Standard Trim Parameters
Some types of machines aren’t equipped with auto trim device. Length After Trim: (Options: 1~7) This parameter is to adjust the length of thread residue caused by trimming. The smaller the parameter value is, the shorter the length of thread BECS-129S Singular-head Computerized Embroidery Machine...
Page 50 The smaller value is, the earlier starting will be. This parameter adjusts the difference between different machines. The effect of trimming will be improved with the proper adjustment on this parameter. BECS-129S Singular-head Computerized Embroidery Machine...
Page 51: Standard Machine Parameters
Setting Parameters 4.9 Standard Machine Parameters These are the machine parameters concerning the flat embroidery. Refer to the appendix for their options and default values. Maximum Speed: (Options: 650, 700, 750, 800, 850, 900, 950, 1000) BECS-129S Singular-head Computerized Embroidery Machine...
Page 52 Frame Curve & Angle: (Options: F1/F2 230, 240, 250) The frame angle means that the frame starts to move when the main shaft rotates to a certain angle. Different frame curve and angle will cause different BECS-129S Singular-head Computerized Embroidery Machine...
Page 53 The user can increase the parameter value to stop the main shaft at a larger angle. The user can adjust the value between 0 and 20 depending on whether the stop position exceeds the stop angle. Needles In A Head: (Options: 3~15) BECS-129S Singular-head Computerized Embroidery Machine...
Page 54 Sequin Style Set: (Options: 3mm, 4mm, 5mm, 7mm, 9mm) These two parameters are used to separately set the size of sequin embroidery for A or B needle position. The changes of these parameters can only be effective upon the repowering of the machine. BECS-129S Singular-head Computerized Embroidery Machine...
Page 55 This parameter is to limit the rotation speed of the main shaft in rope embroidery. Boring Distance:(Options:1~150,for 0.1mm~15mm ) This parameter is to set the distance between the normal needle position and the boring needle position. BECS-129S Singular-head Computerized Embroidery Machine...
Page 56: Common Parameters
The user can adjust it according to the need. Fast Manual Frame: (Options: 0 ~9) This parameter is to set the speed for the fast manual frame-moving. The user can choose the values according to the need. Low Manual Frame: (Options: 0 ~9) BECS-129S Singular-head Computerized Embroidery Machine...
Page 57 When the work sequence is not effective, the user will manually change color according to designs. When this parameter is set as “Yes”, the machine will automatically save the color-change sequence as the work sequence, which can be used in the next embroidery. BECS-129S Singular-head Computerized Embroidery Machine...
Page 58: Part V Manual Operation
Operation: Under the embroidery preparation status “ ” enter the manual operation menu, select the second item “Stop back” by keys BECS-129S Singular-head Computerized Embroidery Machine...
Page 59: Main Shaft Origin
(scaled up/down or repetition embroidered) for a circle, in order to check the design’s position in the frame and to avoid over-frame. ⑴ Press keys “ ” to move the frame to the start point, BECS-129S Singular-head Computerized Embroidery Machine...
Page 60 “Frame Range”. After a while the design range will be shown in the screen. And there will be a prompt: “!Pull Bar To Start”. Then the user can follow the prompts to continue the operation. BECS-129S Singular-head Computerized Embroidery Machine...
Page 61: Embroider Range
⑴ In the main screen and under the embroidery preparation status “ ”, press the manual operation key“ ” to enter the manual operation menu. ⑵ Press the keys “ ” to select the option “Emb. a Line”. Or directly BECS-129S Singular-head Computerized Embroidery Machine...
Page 62: Forward Code Float
5.9 Backward Code Float This operation is to move the frame backward to the pointed position according to stop code in the design quickly, so as to let the machine start embroidery at any point. BECS-129S Singular-head Computerized Embroidery Machine...
Page 63: Forward Sti. Float
“ ” to select the option “Forward Sti. Float”, press the confirmation key “ ”, and then there will be a prompt in the screen asking the user to input the stitches to float. BECS-129S Singular-head Computerized Embroidery Machine...
Page 64: Backward Sti. Float
⑶ Press the numerical keys to input the stitches for floating. Press the confirmation key “ ”，and then the frame will move backward the input stitches in high-speed. BECS-129S Singular-head Computerized Embroidery Machine...
Page 65: Part Vi Disk Management
U disk files. After that the U disks’ light goes on and system begins to read the directory, then the design directories in binary, ternary and Z-scale system will be displayed. The following is an example: BECS-129S Singular-head Computerized Embroidery Machine...
Page 66: U Disk Design Input
(or move the cursor to the location of “2”) and then press the confirmation key “ ”to enter the disk input menu. Then U disks’ light goes on and the driver begins to read the directory and display the directories in BECS-129S Singular-head Computerized Embroidery Machine...
Page 67 ” to set this number. If the number has been used, the confirmation will fail. Otherwise, the user can continue the following operations. ⑷ The system asks to input the design name in memory (memory name). BECS-129S Singular-head Computerized Embroidery Machine...
Page 68 After that, if the system is under embroidery preparation status, it will enter the parameter input operation; if the system is under the embroidery confirmation status, the system will ask the user whether to embroider the input design. BECS-129S Singular-head Computerized Embroidery Machine...
Page 69: Des. Output To Usb Disk
” to select "Yes", then press “ ”, and the system will enter the parameter setting operation. 6.3 Des. Output to USB Disk This is to save the memory designs to the U disk in the “DSB.” format. BECS-129S Singular-head Computerized Embroidery Machine...
Page 70 ⑶ Press the numerical key to input the design’s memory number, or press “ ” to enter the memory design directory to select by pressing keys “ ” and “ ”. (Refer to Part III) BECS-129S Singular-head Computerized Embroidery Machine...
Page 71: Format U Disk
The machine can format the USB disk in DOS format. A new U disk has to be formatted before use. Operation: ⑴ Under the main screen and the status “ ”, press“ ” to enter the disk management menu. Press "4" to select “Format U. Disk”. BECS-129S Singular-head Computerized Embroidery Machine...
Page 72: Delete Usb Disk Design
” to confirm and delete the design file or press “ ” to exit and return to the main screen. Note: This machine supports floppy disk driver with USB interface. The operation of that driver is as similar as that of USB flash disk. BECS-129S Singular-head Computerized Embroidery Machine...
Page 73: Part Vii Memory Design Operation
⑴ Under the main screen, press “ ” to enter the design operation menu and its first page is shown as followed: ⑵ Press keys “ ” to switch between the two pages. The second page: BECS-129S Singular-head Computerized Embroidery Machine...
Page 74: Select Design For Embroidery
” to select No. 15. If there is design No. 15 in the memory, it will be set for embroidery and the parameter setting menu will appear. Refer to Part IV for setting parameters. If there is no design No. 15, the BECS-129S Singular-head Computerized Embroidery Machine...
Page 75 ” to confirm selection. After that the screen will turn to the parameter setting menu. ⑷ If the user doesn’t change parameter setup, press “ ” to exit to the main screen. For parameter setting refer to Part IV. BECS-129S Singular-head Computerized Embroidery Machine...
Page 76: Show Memory Design
” to enter the memory design operation menu. ⑵ Press "2" or “ ” to move the cursor to the second option, and then press the confirmation key “ ” to enter the memory design list: BECS-129S Singular-head Computerized Embroidery Machine...
Page 77: Des. Input
“ ”. ⑶ U. disk driver light is on, and the system begins to read the disk directory and then displays it. Press “ ” and “ ” to select the BECS-129S Singular-head Computerized Embroidery Machine...
Page 78 ” to select "Yes", then press “ ”, and the system will enter the parameter setting operation. (Refer to Part IV for parameter setting.) To embroider the original design, the user needs press “ ” to BECS-129S Singular-head Computerized Embroidery Machine...
Page 79: Delete Memory Design
” to select the design.) Then press the key “ ” to delete the selected design. 7.6 Copy Design This operation is to copy a memory design and save it as a new design in the memory. BECS-129S Singular-head Computerized Embroidery Machine...
Page 80 “ ” and “ ” to select. If there is no such a design in memory, the confirmation will fail. Otherwise the system will provide a minimum vacant design number for the new design. BECS-129S Singular-head Computerized Embroidery Machine...
Page 81: Combine Design
Under the main screen, press “ ” to enter the memory design operation menu and then select the sixth option “Combine Design” and press “ ”. The following interface will be shown on the screen: BECS-129S Singular-head Computerized Embroidery Machine...
Page 82 (3) Input the memory number of the second design in the same way with operation (2). Then the system will provide and display the minimum available memory number for the new design. BECS-129S Singular-head Computerized Embroidery Machine...
Page 83 (4) The user can also input a new number by pressing numerical keys and “ ”. If the number has been used by another design, the confirmation will fail. Otherwise the system will ask user to input the interval between the two designs. BECS-129S Singular-head Computerized Embroidery Machine...
Page 84: Divide Design
⑶ Press numerical keys to input the number of a memory design or choose one from the memory design directory. Then the system will ask user to input number of dividing stitches. BECS-129S Singular-head Computerized Embroidery Machine...
Page 85 ⑸ Confirm the system-provided number or input and confirm a new design number. Then the system will ask user to input or confirm the name of the first new design. BECS-129S Singular-head Computerized Embroidery Machine...
Page 86: Clear All
7.9 Clear All This is to delete all the designs in the memory. Please take caution. Operation: ⑴ Under the status “ ”, press “ ” to enter the design operation menu on the main screen. BECS-129S Singular-head Computerized Embroidery Machine...
Page 87: Check Design
“Design Wrong”. 7.11 Rename File On the second screen of design operation menu, there is an option to change the design’s name. Follow the prompts to select the design and the BECS-129S Singular-head Computerized Embroidery Machine...
Page 88: Expand Satin
Press the confirmation key to confirm the input and the system will complete the change and return to the design operation menu. 7.12 Expand Satin On the second screen of design operation menu, there is an option for expanding satin to create a new design. BECS-129S Singular-head Computerized Embroidery Machine...
Page 89: Design Letter Pattern
0~9. The user can arrange the letters and digits at will to make a new design. Operation: (1) Enter the second page of the design operation menu and select the option “Des. letter pattern”. The following screen will be displayed. BECS-129S Singular-head Computerized Embroidery Machine...
Page 90 The design’s outline is displayed in the screen as follows. The user can adjust the design’s positions, fonts, angles and scales according to the prompts on the left. Then press “ESC” to end the operation. BECS-129S Singular-head Computerized Embroidery Machine...
Page 91 Selecting “Yes” and pressing “ are for entering the next ” step. ⑦ Input the new design number and press “ ” to save the design. ⑧ Then the system will return to the disk management menu. BECS-129S Singular-head Computerized Embroidery Machine...
Page 92: Part Viii Assistant Function
Without setting the frame origin position, the user can not operate this function. That is to say, only when option 5 is at “SET” status, the software position limitation can be set. Operation: BECS-129S Singular-head Computerized Embroidery Machine...
Page 93: Frame Restore
If the origin point hasn’t been set, the option “Frame Restore ” will be in darkness and unavailable for operation. If the origin point has been set, the option “Frame Restore” will be in brightness and available for operation. Operation: BECS-129S Singular-head Computerized Embroidery Machine...
Page 94: Default Setup
” on the main menu to enter the assistant management menu. ⑵ Press keys “ ” to select the option “Default Setup”, and then the entire parameters will be restored to the default values after the user pressed “ ”. BECS-129S Singular-head Computerized Embroidery Machine...
Page 95: Change Ui Language
”, press “ ” on main menu to enter the assistant management menu. ⑵ Press “ ” or “5” to select the option “Set Frame Origin”. Then press “ ” and the following screen will be displayed BECS-129S Singular-head Computerized Embroidery Machine...
Page 96: Machine Self-Test And Test Machine Parts
User can code the mechanical parameters of system via this operation in order to protect the machine from the negative influence caused by the accidental changes of parameter. After password is set, the user has to input the password before changing the parameter values. BECS-129S Singular-head Computerized Embroidery Machine...
Page 97: Set Network Address
PC. Otherwise there will be IP address conflict thus leads the failure of network. Sub mask: 255.255.255.0 Gateway: same to the Dest IP Dest IP: the IP address of the PC server in the LAN Dest Port: 1600 BECS-129S Singular-head Computerized Embroidery Machine...
Page 98: Lan Function Switch
The premises for the machine to successfully link the server are: 1) appropriately setting the IP address 2) the network link is good and network equipments (e.g. HUB, switch) are in the open mode. 3) the server is power on and the software (SemsServer.exe) is open. BECS-129S Singular-head Computerized Embroidery Machine...
Page 99: Net Manual Connect
Note: In order to use the network function, you have to install and use Dahao embroidery monitoring software for client terminal (SemsClient.exe and SemsServer.exe). Please read the introduction in CD attached to the computer system. BECS-129S Singular-head Computerized Embroidery Machine...
Page 100: Set Design Showing-Color
” to choose the color of the needle which he wants to change. You can move the “□” to the color which you wants choose, and then press the key “ ”. In the following picture, the BECS-129S Singular-head Computerized Embroidery Machine...
Page 101 No.1 needle position is changed to black. The method for setting the color of other needles is the same as above description. After the color-set is complete, press “ ” to quit. BECS-129S Singular-head Computerized Embroidery Machine...
Page 102: Appendix
Rep. Times (Y) 1～99 Repetition Interval (X) -999.9～+999.9 Repetition Interval (Y) -999.9～+999.9 Switch Parameters Parameter Choice Standard value Thread broke detect Yes、No Auto Back Origin Yes、No Start Slow Af. Trim 1,2,3,4,5,6,7,8 Adjust Stop Position 0,1,2,3,4,5,6 BECS-129S Singular-head Computerized Embroidery Machine...
Page 103 Not exit embroidery confirm E—14 Memory parameter lost E—15 Memory design lost E—16 No design in memory E—17 No free design numbers E—18 Memory design number does not exist E—19 No enough memory space E—50 Encoder abnormal BECS-129S Singular-head Computerized Embroidery Machine...
Page 104 E—75 Trimming motor overtime E—80 Over-current, Restart E—89 Lost Continuous Pulse E—110 Error At Saving code E—130 No Respond from U disk E—131 Rsp Disagree Command E—151 No Device E—152 Device Err E—153 File Exist BECS-129S Singular-head Computerized Embroidery Machine...
Page 105 Please ensure that the disk or U disk is in the state of writing-in mode. E—05 No free space in disk directory No more directories can be established in the floppy/USB disk. E—06 No free space in disk BECS-129S Singular-head Computerized Embroidery Machine...
Page 106 In manual or automatic returning (tracing back), the machine has reached the origin point of the design. E—13 Not exit embroidery confirm It appears when the user operates machine without quitting the embroidery confirmation status. Press the embroidery confirmation key to exit. BECS-129S Singular-head Computerized Embroidery Machine...
Page 107 E—19 No enough memory space Because of occupation by memory designs, the memory can’t provide enough space for design input or design review. E—50 Encoder abnormal Encoder abnormal results in incorrect embroidery. Check the cable BECS-129S Singular-head Computerized Embroidery Machine...
Page 108 Overtime of color change means that the color change motor can’t change color to the set position within the designated time. The cause may be the motor stopping rotation caused by wrong mechanical installation, or the connection BECS-129S Singular-head Computerized Embroidery Machine...
Page 109 E—59 Color-change motor reverse It’s the motor reverse rotation caused by reverse connection of the motor wire winding. E—61 Frame software limit BECS-129S Singular-head Computerized Embroidery Machine...
Page 110 E—80 Over-current, Restart BECS-129S Singular-head Computerized Embroidery Machine...
Page 111 E—151 Device Full The USB disk is full or its remaining space is not enough to input a certain file. E—152 Device Err This may be caused by: malfunction of the USB disk or E1904A hasn’t BECS-129S Singular-head Computerized Embroidery Machine...
Page 112 E—157 File Not Open The file hasn’t been opened successfully. E—158 State Err Something wrong comes out in the process of reading the USB disk sections. E—159 Sys Err Something is wrong in the file system. BECS-129S Singular-head Computerized Embroidery Machine...