Summary of Contents for Certified International 054-7159-4
- Page 1 ANGLE GRINDER IMPORTANT: INSTRUCTION Please read this manual carefully before using this angle grinder and MANUAL save it for reference.
-
Page 2: Table Of Contents
054-7159-4 TABLE OF CONTENTS Specifications Safety guidelines Work area safety Read and understand this instruction manual thoroughly before using the Electrical safety product. It contains important information for your safety as well as operating and maintenance advice. Personal safety Keep this instruction manual for future use. -
Page 3: Specifications
054-7159-4 SPECIFICATIONS MAINTENANCE Motor 120V~, 60 Hz, 5.5A CLEANING Single speed 12,000 RPM (no load) LUBRICATION Arbor size 5/8” (16 mm) STORAGE AND HANDLING OF THE WHEELS Disc diameter 4 1/2” (115 mm) Weight 4 lb 3 oz (1.89 kg) -
Page 4: Work Area Safety
054-7159-4 WORK AREA SAFETY Damaged or entangled cords increase your fingers on the switch or energising adjustments, changing accessories, or the risk of electric shock. power tools that have the switch on storing power tool. Such preventative •... -
Page 5: Safety Warnings Common For Grinding
054-7159-4 SAFETY WARNINGS COMMON FOR • Do not use a damaged accessory. Before or arm may be pulled into the spinning the direction opposite of the accessory’s each use inspect the accessory such as accessory. rotation at the point of the binding. For... -
Page 6: Safety Warnings Specific For Grinding
054-7159-4 • Do not attach a saw chain woodcarving • Wheels must be used only for ADDITIONAL SAFETY INFORMATION protecting insulation. Double-insulated blade or toothed saw blade. Such blades recommended applications. For example: tools do not need to be grounded. -
Page 7: Minimum Gauge For Cord Sets
054-7159-4 source, be sure to use an extension cord that has the capacity to handle the current the WARNING ICONS tool will draw. An undersized cord will cause a drop in line voltage, resulting in overheating Some of the following symbols may be used on this tool. Please study them and learn their and loss of power. -
Page 8: Installing The Side Handle
054-7159-4 INSTALLING THE SIDE HANDLE (FIG. 1) Description Description Fig. 1 On/Off switch Grinding wheel guard • Unplug the grinder. Threaded clamp nut Side handle Backing flange Wrench • Screw the side handle into the gear Spindle lock button housing. -
Page 9: Adjusting The Wheel Guard
054-7159-4 • With the guard latch open, rotate the spindle lock only when the tool is turned off Fig. 3 Fig. 5 guard into the desired working position. and the wheel has come to a complete stop. The guard body should be positioned... -
Page 10: Switch The Grinder On/Off
054-7159-4 If the wheel you are installing is more than SWITCH THE GRINDER ON/OFF Fig. 10 Fig. 8 1/8" (3 mm) thick, place the threaded clamp (FIG. 10) nut on the spindle so that the raised section •... -
Page 11: Grinding With Grinding Wheels
054-7159-4 GRINDING WITH GRINDING WHEELS CLEANING Fig. 11 (FIG. 11) Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. - Page 12 054-7159-4 1-YEAR LIMITED WARRANTY such as, but not limited to, fuel, PROBLEM PROBABLE CAUSE SUGGESTED CORRECTIVE ACTION lubricants, vacuum bags, blades, belts, Power cord is not plugged in. Plug tool into power source. This CERTIFIED product is guaranteed sandpaper, bits, fluids, tune-ups or Replace fuse or reset tripped circuit breaker.
-
Page 13: Warranty
054-7159-4 exemplary damages arising in connection with the sale, use or inability to use this product. NOTICE TO CONSUMER This warranty gives you specific legal rights, and you may have other rights, which may vary from province to province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation.