Related Manuals for Zodiac Pool Systems TRi-XO CrossOver
Summary of Contents for Zodiac Pool Systems TRi-XO CrossOver
- Page 1 CHLORINATOR USE WITH SALT AND MINERAL SALTS Rainbow Pool Products PO Box 2388, Mansfield Qld 4122 Telephone STD 61-7-3849 5385 Facsimile STD 61-7-3849 5384 Email: info@rainbowpoolproducts.com.au Web: www.rainbowpoolproducts.com.au...
- Page 2 WELCOME TO ZODIAC Congratulations on your purchase of the Zodiac TRi-XO CrossOver Chlorinator. TRi-XO allows users to select between using normal pool salt or mineral salt blends. Simply select the type of salt you are using from the start up screen to program it into the software.
- Page 3 ZODIAC BELIEVES IN SAFETY FIRST At Zodiac, we take safety seriously. Always exercise caution when using electrical appliances and follow the instructions. Failure to do so could result in permanent injury, electrocution or drowning. IMPORTANT INFORMATION YOU MUST READ THIS INFORMATION BEFORE INSTALLATION. ALWAYS READ THE LABEL AND OPERATION MANUAL BEFORE USING.
- Page 4 ZODIAC BELIEVES IN SAFETY FIRST CHILD SAFETY Children should not be allowed to operate or perform maintenance on this product. No one, particularly children, should sit, step, lean, or climb on any of your pool’s operational system. In the interests of child safety, all components of a pool’s operational system should be located at least 3.5 metres away from the pool.
- Page 5 INSTALLATION GUIDE POSITIONING THE POWER PACK 1. Locate a suitable space for the power pack bracket. It should be installed no further than 1.8 metres away from the cell - ideally in a 2. Using screws provided, fasten the bracket securely to the wall and position the power pack on the bracket.
- Page 6 NAVIGATION BUTTONS 6. Plug your pool pump into the outlet socket in the bottom of the TRi-XO 7. Once all connections are together press the mains power switch to ON. Use the following UI buttons to access and select all menus and commands: ON/OFF Turn Chlorinator on/off.
- Page 7 SELECTING THE RIGHT SALT TYPE At start up it is necessary to select the correct salt type being used in the pool. If using salt or using a mineral blended salt simply select the correct type as shown on the screen once the unit is powered up. 1.Use to scroll to the right selection 2.
- Page 8 USING INBUILT CLOCK AND TIMERS When it comes to chlorination, every pool is different. To get what’s right for you, you will need to set the unit’s clock and timers. SETTING THE CLOCK 1. Press the button to enter the MAIN MENU. 2.
- Page 9 USING INBUILT CLOCK AND TIMERS TURNING CHLORINE GENERATION ON The chlorine generation of the TRi-XO can be controlled in a number of ways: 1. Manually set to an output level, with the operating times determined by an external timer. 2. Using the in-built timers on the TRi-XO unit (refer to ‘ ’) 3.
- Page 10 USING INBUILT CLOCK AND TIMERS To program the timer: 1. Press the button. 2. Press button to move arrow to ‘SET TIMERS’. 3. Press to enter the ‘SET TIMERS’ menu. 4. Press to select the timer you wish to set. (Timer 1 or Timer 2) 5.
- Page 11 USING INBUILT CLOCK AND TIMERS CLEARING THE TIMERS To clear the timer: 1. Press the button. 2. Press button to scroll to ‘SET TIMERS’. 3. Press to enter the ‘SET TIMERS’ menu. 4. Press to scroll to ‘CLEAR TIMERS’. 5. Press EXTERNAL TIME CLOCK At times, it may be desirable to control chlorine generation using an external time switch.
- Page 12 CHLORINE OUTPUT LEVELS SETTING THE CHLORINE OUTPUT The amount of chlorine required by your pool is dependent on a number of factors including the size of the pool, the number of users and the climate. Output will appear as a percentage on the screen readout.
- Page 13 CORRECT SETTINGS FOR YOUR POOL...
- Page 14 CONNECTING TO A CONTROLLER You must set the controller type on the TRi-XO before making the wiring connection. SETTING THE CONTROLLER (To be done before making a wiring connection) Switch power to the TRi-XO unit on. Wait for the start-up sequence to complete. Press the button.
- Page 15 CONNECTING TO A CONTROLLER ATTENTION JANDY ‘REV L’ OR LATER USERS It is critical that the controller setting be set to the correct Zodiac, Jandy or Pentair controller designation. There are a number of different revisions locked into the TRi-XO software. Please see the controller user manual to determine the model and/or revision you are using.
- Page 16 CONNECTING TO A CONTROLLER 3. Remove the lower cover from the TRi-XO unit. 4. Remove the small white bung closest to the centre of the lower panel of the TRi-XO unit. 5. Thread the controller cable through the hole (a grommet may be necessary depending on the size of the cable being used).
- Page 17 CONNECTING TO A CONTROLLER TESTING THE WIRING CONNECTION Once a connection has been made between the Controller and the Chlorine generator, it will need to be tested. 1. Turn on the power to the Controller and the Zodiac TRi.-XO 2. If successful, a ‘ ’ symbol will appear in the top right hand corner of the screen after about 20 seconds.
- Page 18 SETTING THE MODE TO LOW: IMPORTANT IF USING A POOL COVER If your pool has a cover, you should set the output level to “low”. This is also known as “winter” mode. Reducing your chlorine output will help prevent damage to your pool’s cover and other equipment. MANUAL SETTING 1.
- Page 19 THE BOOST SETTING At times your pool may require a larger than normal application of chlorine. The Boost function is used to rapidly add chlorine. In BOOST or “Superchlorinate” mode, output settings are temporarily overridden and the chlorine generator runs for 24 hours at 100% Chlorine Production.
- Page 20 HELP AND TROUBLESHOOTING The Zodiac TRi-XO chlorine generator automatically provides a number of inbuilt warnings that can help identify problems and offer solutions. To access the HELP menu: 1. Press the button. 2. Using the buttons, scroll to the ‘HELP/DIAG’ menu. 3.
- Page 21 MAINTENANCE To keep your TRi-XO Unit in the best possible condition it is recommended regular maintenance should be performed. INSPECTING AND CLEANING THE ELECTRODE In areas that experience calcium hardness the TRi-XO electrode will To clean your electrode: and unplug the cell terminal cap. 2.
- Page 22 MESSAGES AND WARNINGS. WHAT THEY MEAN. Messages Meaning Solution Check Salt Your salinity level Take a water sample to the pool shop Check Minerals may be low to see if your salt or mineral levels need topping up. Please note that this can be affected by low water temperatures.
- Page 23 Express Warranty* Zodiac Group Australia Pty Ltd (Zodiac Australia) warrants that the Zodiac TRi-XO CrossOver Chlorine Generator will be free from defects in materials and workmanship for the period of 3 years from the date of purchase. * The warranty applicable to commercial application is limited to 12 months from the date of installation.
- Page 24 ZODIAC AUSTRALIA - EXPRESS WARRANTY AND GUARANTEES 4 Without limiting 3 above, products sold by Zodiac Australia are designed for use with swimming pool water balanced in accordance with Australian Standard AS3633-1989 with a pH range of 7.0 - 7.8. Maximum chlorine readings should not exceed 4ppm.
- Page 25 ZODIAC AUSTRALIA - EXPRESS WARRANTY AND GUARANTEES How to make a warranty claim 9 The Purchaser must telephone or email Zodiac Australia Customer Service and obtain a warranty ID number for the warranty claim. Contact details are: Zodiac Group Australia Pty Ltd 219 Woodpark Road Customer Service Telephone: 1300 763 021...
- Page 26 ZODIAC AUSTRALIA - EXPRESS WARRANTY AND GUARANTEES Additional guarantees, rights and remedies Australian Purchasers - Guarantees under the Australian Consumer Law rights and remedies Australian consumers have under the Australian Consumer Law. 13 Zodiac Australia products come with guarantees that cannot be excluded under the Australian Consumer Law.