Table of content Operating guide How to read this operating guide Qualified Personnel Need a little Help? Copyright Notice Basic description Installing the Me2 Working with the Me2 The Keyboard LCD Saver Menu Tree Operating instructions DMX Control Bootloader RDM Control...
Operating guide Congratulations! You are now in possession of a MDG Me2 Fog Generator. We hope this Me2 Fog Generator will bring you long hours of satisfaction. Please read the following instructions carefully and completely before filling your Fog Generator with the MDG Neutral Fog Fluid and turning it on.
Please refer to local authorities for further information. EED A LITTLE At MDG, we try our best to provide you with complete information for our products. Despite our best efforts, sometimes, a little more is required due to the specifics of your project and installation.
It is one of the quietest units on the market. At the heart of the MDG Me2 is an electronic assembly that keeps the heat exchanger at a very stable temperature, with three different types of fail-safe systems. Those three types of electronic fail-safe systems are designed to protect against over and under-heating conditions and against component failure.
Page 7
Me2, Fog Generator Fog fluid reservoir Handle Fog output nozzles USB Connector Keyboard MAIN POWER Switch XLR-5 DMX/ RDM Connector VAC Input 100-250 VAC or N Gas input 50/60 Hz (50-60 psi) Operating Guide, Rev: A/a 7 / 30...
Installing the Me2 Exercise caution when selecting the location to install or use this equipment: Install the MDG Me2 away from rain, wind, heavy dust or any harsh environment situations. Ensure available space for all electrical cable and gas tubing runs, ...
Me2, Fog Generator Working with the Me2 The MDG Me2 Fog Generator is quite easy to operate and requires no preventive maintenance. Switch On the power. The MDG Me2 will display during four (4) seconds, the following message: Me2, by MDG Fog Generators Testing BootLoad….
Me2, Fog Generator EYBOARD The user can scroll in the menu by using the buttons of the keyboard: ‘Down’ moves the selection to the next menu, or decrease a data value. When at the end of a list, the program moves back to the first item of this list.
Status Menu summarizes all the state of the fog generator. None of its sub menus can be modified. Control Menu allows the user to control locally the MDG Me2. All its sub menus can be set, as long as the generator is not in DMX/RDM mode.
Page 12
Me2, Fog Generator The tree menu architecture is explained below. Items highlighted in blue are state menu ( - ), and those highlighted in yellow are control menu ( ). STATUS Status menu STATE ---- Status State UNIT OFF...
Page 13
Me2, Fog Generator INTERFACE Network /DMX/RDM Menu COMM. ---- Communication toggle AUTO - the generator is controlled by DMX/RDM if a signal is present, or locally if there is no signal - the generator is controlled by the keyboard ONLY...
When powering up the generator, the control program configures the Input/Output, and loads the configuration parameters saved in the EEPROM memory. At this point, the MDG Me2 switches to stand-by mode, and most of the electronic controls are off. When the generator is manually switched to «UNIT ON» mode («CONTROLUNITON»), the program starts the heating cycle («STATUS...
Page 15
FAIL state mode is initiated if any critical error occurs. In this state, the MDG Me2 is off, awaiting an action from the user. A critical error is always displayed in the Status Menu («STATUSERROR»), as well as the five (5) last critical errors («STATUSLAST ERR»),...
Page 16
Me2, Fog Generator ERROR = T. HIGH LAST ERR CODE = 4 This error will occur if the temperature of the heating module is too high. This is generally due to an electronic problem. Shut down the generator and restart it.
AUTO»), controls MDG Me2 by DMX, only if there is a signal. If the DMX wire is unplugged or DMX signal is lost, the generator keeps the last DMX values. WARNING In «AUTO Mode», DMX commands always take precedence over Local commands.
Me2, Fog Generator OOTLOADER The MDG Me2 uses a BootLoader, also called boot manager. This program is a firmware (software embedded in a hardware device) located into the non-volatile memory of the microcontroller unit (MCU) that allows in-circuit reprogramming of the device using its USB communication port.
Page 19
Me2, Fog Generator The RDM supported parameters implemented in the MDG Me2 Fog Generator are summarized in the following table. RDM Parameter ID’s Value Comments Allowed Allowed DISC_UNIQUE_BRANCH 0x0001 DISC_MUTE 0x0002 DISC_UN_MUTE 0x0003 QUEUED_MESSAGE 0x0020 STATUS_MESSAGES 0x0030 SUPPORTED_PARAMETERS 0x0050 ...
CAUTION DISCONNECT UNIT BEFORE ADDING FOG FLUID. To fill the fluid reservoir, unscrew the brass cap and pour the MDG Neutral Fog Fluid until it reaches the inside bottom of the opening. Avoid overfilling, screw back the brass cap and make sure it is tightened.
Me2, Fog Generator Troubleshooting Contact MDG if symptoms are not listed, or if the provided solutions fail to resolve the issue. Table 2: Symptoms and Solutions Symptoms Probable Causes and Suggested Actions Verify that AC power cord is properly The fog generator does not switch on connected on both ends.
Page 22
You have solenoid valve malfunction. Restart the generator. Please contact MDG Service if this problem persists. ERROR = HEATER This is a heating timeout, due to a cartridge heater problem. Restart the generator and check the heating status «STATUSSTATE = xx%...
Page 23
Stop the generator for a few minutes, if it is possible Try to change the position of the generator to a cooler location. Please contact MDG Service if this problem persists. ERROR = WD RESET Restart the generator.
Me2, Fog Generator Accessories LIGHT Whether by plane, train or automobile, make sure your fog generator travels safe. Our sturdy flight cases have high-quality padding to make the journey easier on your generator, with special compartments accessories like cable extensions and remote control timers.
Me2, Fog Generator Technical specifications Series Series Maximum fog output (per minute): 200 m (7,063 ft Fog colour: Pure white Particle size: 0.5 to 0.7 microns Fluid consumption: 2 L (59.5 oz / 0.53 US gal) per hour at 2.76 bar / 40 psi...
MDG Neutral Fog Fluids has been used. MDG Fog Generators Ltd is not responsible for any damages resulting from a faulty installation or from abusive use of the product.
Need help?
Do you have a question about the ME2 and is the answer not in the manual?
Questions and answers