1. Manuals
  2. Brands
  3. LOBSTER Manuals
  4. Cutter
  5. EH-19PCU
  6. Owner's manual & operating instructions

LOBSTER EH-19PCU Owner's Manual & Operating Instructions

Electric-hydraulic rebar cutter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Model EH-19PCU Electric-Hydraulic Rebar Cutter
Read safety and instructions carefully before using this tool.
SAVE THIS OWNERS MANUAL & OPERATING INSTRUCTIONS
Max. Cutting Capacity
Voltage
Power Consumption
Weight
Dimensions (L x W x H)
7248 Inama Rd., Sauk City, WI 53583
Phone: (608)643-6678 Fax: (608)643-2682
Specifications and prices shown in this document are subject to change at any
time. For the latest detailed information, please contact Fascut Industries.
Fascut Industries Inc.
www.fascut.com
#6 (3/4") - Grade 60 rebar
110-120 Volts AC, 50/60 Hz
800 Watts / 7.2 amps
22 pounds
17" x 4½" x 8½"

Advertisement

Table of Contents
loading

Summary of Contents for LOBSTER EH-19PCU

  • Page 1 Model EH-19PCU Electric-Hydraulic Rebar Cutter Read safety and instructions carefully before using this tool. SAVE THIS OWNERS MANUAL & OPERATING INSTRUCTIONS Max. Cutting Capacity #6 (3/4") - Grade 60 rebar Voltage 110-120 Volts AC, 50/60 Hz Power Consumption 800 Watts / 7.2 amps...

  • Page 2: Safety Requirements

    Safety Requirements For your own safety and protection, do not attempt to operate this tool until it is completely assembled and installed according to the instructions… and until you read and understand all the safety requirements. FOR POWER TOOLS WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
  • Page 3 13. Avoid unintentional starting. Do not carry the tool with finger on the switch. Be sure switch is off when plugging in. Use switch lock behind trigger switch when not in use. 14. Avoid using an extension cord. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock.
  • Page 4 8. If the tool makes an abnormal sound during operation, discontinue use immediately. Return the tool to Fascut Industries for repair. 9. Do not add hydraulic oil if the tool is warm or immediately after heavy duty operation. Oil will be under a slight pressure when tool is warm. 10.
  • Page 5 #3 - Is the electrical power supply correct? Use this tool only with a power supply that meets the rating indicated on the tool. #4 - Using an extension cord? An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock.
  • Page 6 3. Position the rebar to be cut at a right angle to the tool head and secure by adjusting the adjusting screw. This will hold the rebar at a right angle to the cutting direction. 4. Confirm where the dangerous range is. Cut pieces may fly off with tremendous force within the dangerous range as shown.

  • Page 7: Emergency Manual Release

    Emergency Manual Release For emergency reasons, it may become necessary to manually retract the moving cutting blade. To do this, loosen the Release Valve no more than ¼ turn using the M5 Hex Key Wrench. The moving blade will return to its starting position.

  • Page 8: Maintenance

    Maintenance 1. Changing the blades. If a blade is dull or damaged, immediately replace with a new blade. Cutting with dull or loose blades WILL damage the tool. Unplug the tool before starting maintenance of any kind. 2. Check the length of the carbon brushes every six months. Unplug the tool and loosen the brush caps using a screw driver.

  • Page 9: Storage Method

    Storage Method The tool should be stored in a dry, high or locked up place out of reach of children. Clean prior to long term storage. Coat metal parts with a rust inhibitor. Trouble Shooting If the remedy listed below does not solve the problem, the tool MUST be returned to Fascut Industries for service.
  • Page 11 Lobster EH-19PCU Fascut Industries Inc. March 1, 2011 Qty. Index # Description Code Price Ea. Req. Cutter Head 40626 $662.61 Washer, Spring Lock, M6 25592 $0.20 Screw, Socket Head Cap, M6x20 25593 $0.45 Cutting blade w/washers & screws 29044 $37.50...
  • Page 12 Screw, Support, M12x35 25623 $5.20 Support Screw locking nut, M12 25624 $1.30 Key, Piston 25628 $5.10 Pump Frame (frame only) 25625 $415.50 Steel Ball, 4.8 mm (3/16) 12360 $0.20 O-ring, Relief Valve, P-3 10333 $0.35 Relief Valve 25606 $14.13 Label, Name Plate 40622 $1.86 Washer, Sealing...
  • Page 13 Cable Tie 24316 $0.30 Oil Tank Case Housing 40354 $327.12 O-ring, Oil Tank, P-32 25813 $3.20 Oil Seal, 12-28-7 28071 $13.28 Washer, M5 28032 $0.10 Screw, Socket Head Cap, M5x30 w/lock 28033 $0.50 Trigger Switch Spring Plate 26698 $8.10 Grab Handle 40627 $44.80 Oil, 12-oz ISO-46...

Table of Contents