Advertisement
Quick Links
Model XS1000
TCP/IP to RS232/422/485 Device Server
User's Manual
1.0 Introduction
The XS1000 is a cost effective and highly integrated
Serial-to-Ethernet 10/100Mbps device server. Embedding a
8051CPU with 64KB OTP ROM and 32KB SRAM. The serial
interface supports handshake signals RTS and CTS. The
XS1000 can access a serial RS232/422/485 device located
virtually anywhere (via Ethernet or Internet). It automatically
finds devices on the network and can be configured by a
web-browser.
2.0 Features:
♦ 3-in-1 RS-232/422/485 interface Max.230Kbps Serial
interface and 10/100 Mbps Ethernet.
♦ Supports 4- and 2-wire RS-485 with AUTO-SEND™.
♦ Terminal block for easy RS-422/485 serial wiring
♦ Supports IP configuration by MAC address.
♦ Supports Driver, TCP Server/Client, UDP Server/Clie
Pair
Connection protocols.
♦ Easy and powerful configuration management.
♦ Approvals: CE, RoHS.
3.0 . Hardware Installation & Initial Setup
3.1 RS-232 Configuration：（DB9 Male）
（DB9Male）
Signal
PIN2
PIN3
PIN5
PIN7
PIN8
3.2 RS-422/485 Configuration：（terminal header）
Terminal
1
2
No
RS-422
T+
T-
RS-485
485+
485-
3.3 Connecting to 10/100M：
Use a standard Ethernet cable to connect the XS1000 to an
Ethernet switch, or use a cross-over cable if you connect it
directly to a PC.
3.4 Power Supply：
The XS1000 needs a 9 to 24VDC 1000mA power supply.
3.5 XS1000 LED indication：
LINK:
Ethernet Link established.
ACT:
Data flow TX/RX.
PWR:
Power ON.
nt and
Copyrights © U.S. Converters
I/O
RXD
IN
TXD
OUT
GND
-
RTS
OUT
CTS
IN
3
4
5
6
R+
R-
VIN
GND
-
-
VIN
GND
3.6 Connection Diagram
RS-232 Connection
RS-422 Connection
RS-485 Connection
Advertisement
Summary of Contents for U.S. Converters XS1000
- Page 1 3.3 Connecting to 10/100M： XS1000 can access a serial RS232/422/485 device located Use a standard Ethernet cable to connect the XS1000 to an virtually anywhere (via Ethernet or Internet). It automatically Ethernet switch, or use a cross-over cable if you connect it finds devices on the network and can be configured by a directly to a PC.
- Page 2 XS1000. Your computer must have an Ethernet card and TCP/IP installed. B. The default IP address of the XS1000 is 192.168.2.1. Open your web browser and enter this IP address to connect to the XS1000.
- Page 3 Nickname: the product’s NetUART model name. Number is same as your remote control application If you want to keep the connection between XS1000 and your remote control application always on, then set the value of item using the correct value of Remote Host IP Address.
- Page 4 Silent time: If there is no data sent or received for the number of milliseconds specified the connection is dropped. Drop character: Drops the delimiter character of the serial port when sending to TCP, (the receiver doesn't display the character). Copyrights © U.S. Converters...
- Page 5 9. Hold the reset button for about 10 seconds and release it. No LED light indication will show when the unit has been reset, you just have to hold the button for 10 seconds. 10. The XS1000 now has been reset to factory settings.
Need help?
Do you have a question about the XS1000 and is the answer not in the manual?
Questions and answers