Binks 43P6370-0000-6 Manual

Binks 43P6370-0000-6 Manual

Medium-volume plural component (spray and/or pour) dispensing device

Advertisement

Quick Links

Nozzle

deScRiPtion

The Binks Model 43P is a low to medium-volume plural
component (spray and/or pour) dispensing device designed
specifically for plural component systems. Capacity is up
to 20 lbs. spray using a patented static mixing principle.
The 43P, and its companion the 43PA (automatic), uses
the opposed internal orifices principle with no moving
parts (patented).
Spray patterns are by nozzle selection.
Gun output is dependent upon nozzle and impingement
orifices in conjunction with applied fluid pressures.
Impingement orifices usually are matched but may be
dissimilar to "balance" divergent viscosities and/or ratios.
43P Airless Gun
Model: 6370-0000-6
Safety
lock
SolveNt
The 18-8 stainless steel head is designed with cross-
drilled ports for ease of maintenance. The ports allow
access to remove impacted cured resins. Immersion in
solvent will not affect the PTFE seals.
Both resin (1/4 NPS) ports have check valves. The needle
valves share common parts (springs, housing, take-up nuts,
packings and followers) for simplicity. The resin needles
are ball type, the purge is tapered tip.
The rugged forged aluminum gun handle is anodized for
corrosion resistance. The trigger's finger geometry affords
comfortable trigger pull and operation.
PuRge
Part
Replaces
Part Sheet
Sheet
77-1722R-12
77-1722R-11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 43P6370-0000-6 and is the answer not in the manual?

Questions and answers

Summary of Contents for Binks 43P6370-0000-6

  • Page 1 Safety lock SolveNt deScRiPtion The Binks Model 43P is a low to medium-volume plural The 18-8 stainless steel head is designed with cross- component (spray and/or pour) dispensing device designed drilled ports for ease of maintenance. The ports allow specifically for plural component systems. Capacity is up access to remove impacted cured resins.
  • Page 2 ReSPonSiBility of tHe eMPloyeR to PRoVide tHiS infoRMAtion to tHe oPeRAtoR of tHe eqUiPMent. foR fURtHeR SAfety infoRMAtion ReGARdinG BinkS And deVilBiSS eqUiPMent, See tHe GeneRAl eqUiPMent SAfety Booklet (77-5300).
  • Page 3 Binks Model 102-1700 (43P) AiRleSS SPRAy GUn Your Binks 43P Airless Spray Gun has been thoroughly vent through system until all traces of material are tested before leaving the factory. No adjustment is removed. Pack gun mixing chamber with petro- required prior to its operation other than installing the leum jelly.
  • Page 4 Binks Model 102-1700 (43P) AiRleSS SPRAy GUn item 38 Safety “oN” Position flat faces Downward Safety “off” Position flat faces upward PARtS liSt (When ordering, please specify Part No.) iteM PARt iteM PARt deScRiPtion qty. deScRiPtion qty. 102-3327 Nut ......
  • Page 5 MAintenAnce inStRUctionS A. Short Period Shut-down. d. fluid inlet fittings, (two) items 20. 1. When stopping operation of the Model 43P gun for short 1. Be sure check valve assembly (20) is clean and moving periods exceeding 1/2 hour, remove nut (1), nozzle tip (2), freely before connecting hoses.
  • Page 6 noteS...
  • Page 7 noteS...
  • Page 8 WARRAnty this product is covered by Binks’ 1 year limited Warranty. Binks Sales and Service: www.binks.com U.S.A./ canada customer Service toll free customer Service 77-1722R-12 Revisions: Ptfe reference update and technical Support 195 Internationale Blvd. throughout; (P1) corrected model number;...

Table of Contents