Advertisement
Quick Links
Advertisement
Summary of Contents for Ledj FOLL010
- Page 1 FS 100 LED Followspot User Manual Order code: FOLL010...
-
Page 2: Safety Advice
Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE- FULLY BEFORE YOUR INITIAL START-UP! • Before your initial start-up, please make sure that there is no damage caused during transportation. • Should there be any damage, consult your dealer and do not use the equipment. • To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. • Please note that damages caused by user modifications to this equipment are not subject to warranty. CAUTION! CAUTION! TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT! AWAY FROM RAIN, HIGH VOLTAGE-RISK MOISTURE AND LIQUIDS OF ELECTRIC SHOCK!! - Page 3 • Rear positioning handle • 3 push button menu with LED display • PowerCON input • 3-Pin XLR input/output • Fan cooled Specifications 9° - Lux 35600 3930 1300 Power consumption 118W 14° - Lux 18090 2260 Power supply 100~240V, 50/60Hz Fuse F2A 250V 9° 14° Dimensions 270 x 280 x 585mm Weight 6.4kg Order code FOLL010 280mm 585mm www.prolight.co.uk FS 100 LED Followspot User Manual...
-
Page 4: Technical Specifications
Technical specifications POWER INPUT: 100-240V~50/60Hz SHUTTER OPEN BLACKOUT 100W LED FOLLOWSPOT COOL WARM ZOOM WHITE WHITE YELLOW FUNCTION SELECT • DMX MODE • MANUAL MODE FUSE: BLUE GREEN PURPLE PINK DOWN F2A 250V FOCUS IRIS DIMMING DIMMING DMX OUTPUT DMX OUTPUT DMX INPUT DMX INPUT www.prolight.co.uk... - Page 5 Operating instructions Functions: Dimmer - Turn clockwise to increase the intensity, and anti-clockwise to decrease the intensity. Shutter - The LED display will show when the shutter is open and when the shutter is closed. Colour buttons - Allows the user to choose between 6 colours plus 3200K and open. Function selection button - Use this button to switch between DMX and Manual modes (Mode is indicated by LEDs above display) LED display/Status LEDs - The LED display shows the DMX address and fixture status. The status LEDs show the user whether the unit is in DMX or Manual modes and whether it is receiving a DMX signal. Up/down buttons - These are used to change the DMX address. DMX mode: Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show. In this mode you will be able to control each individual trait of the fixture and each fixture independently. To access the DMX mode, press the “FUNCTION SELECT” button on the rear of the unit to show on the LED display and the DMX mode LED is illuminated. The unit is now in DMX mode. Now use the “UP” and “DOWN” buttons to set the desired DMX address. 2 channel mode: Channel Value Function 000-031 Open (cool white) 032-063 3200K 064-095 Red 096-127 Yellow 128-159 Blue 160-191 Green 192-223 Purple 224-255 Pink 000-255 Master dimmer (0-100%)
-
Page 6: Dmx Setup
DMX setup Setting the DMX address: The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start address” from 1- 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the chain starts at 107. DMX 512: DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a data “out” terminal). DMX linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. DATA cable (DMX cable) requirements (for DMX operation): This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output, see image below. Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers. - Page 7 DMX setup Notice: Be sure to follow the diagrams below when making your own cables. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behaviour. Special note: Line termination: When longer runs of cable are used, Termination reduces signal transmission you may need to use a terminator on problems and interferance. it is always advisable to connect a DMX terminal, the last unit to avoid erratic behaviour. (resistance 120 Ohm 1/4 W) between pin 2 Using a cable terminator will decrease (DMX-) and pin 3 (DMX+) of the last fixture. the possibilities of erratic behaviour. (3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89) 5-pin XLR DMX connectors: Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
-
Page 8: Weee Notice
WEEE notice Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. www.prolight.co.uk FS 100 LED Followspot User Manual...