Page 1 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. DIGITAL SINGLE LENS REFLEX CAMERA 2009F0500-1 DSLR-A300_L2 © 2009.6 Sony EMCS Co. 9-852-277-33 Published by Kohda TEC...
Page 2: Specifications
SPECIFICATIONS Camera [Viewfinder] [Others] Type Fixed eye-level penta- PictBridge Compatible [System] Dach-mirror Exif Print Compatible Camera Type Field of View PRINT Image Matching III Digital Single Lens Reflex 0.95 Compatible Camera with built-in flash Magnification Dimensions Approx. 130.8 × 98.5 × and interchangeable lenses 0.74 ×...
Page 3: Unleaded Solder
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Page 4 ENGLISH JAPANESE ENGLISH JAPANESE 1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUS PLATE 1 Remove two claws pushing part A below, 3 Remove focus plate and VB spacer. and remove VM FS retainer in the direction of arrow. VB Spacer Claw Claw Focus Plate...
Page 5 Ver. 1.2 2008.06 ENGLISH JAPANESE ENGLISH JAPANESE 1. SERVICE NOTE 1-1. 各種薬品の取り扱いについて現在使用されている薬品の中には揮発性の高い薬品もあります。それらを不用意に取り扱い蒸発させてしまうと，環境や健康へ影響を与えたり，資源の無駄使いになります。各種薬品は，下記の点に注意して取り扱ってください。・保管場所を定め，高温になったり直射日光の当たらない場所に密閉して保管してください。・小分け（ハンドラップ等）する数は必要最小限に留め，容器による自然蒸発を防いでください。・作業に使用しない時は，必ずキャップ等をして自然蒸発を防いでください。・薬品を使用する回数を極力少なくし，使用する場合は使用する量だけ容器より出して受け皿に残さないようにしてください。 1-2. 樹脂系部品の取り扱いについて本機に使用されている樹脂系の部品は，下記の点に注意して取り扱ってください。・清掃には薬品を使用せず，清掃紙や清掃布を使用してください。やむを得ず汚れがひどくて薬品を使用する場合は，シンナー，ケトン，エーテルは使用しないでください。・各部品の取り付けには指定されたねじを使用し，部品に対して垂直に取り付けてください。また，ねじを締め付ける時は，無理な力を加えないでください。 1-3. 無鉛半田について本機には無鉛半田が使用されています。無鉛半田を使用している基板には，無鉛（Lead Free）を意味するレッドフリーマークがプリントされています。（注意：基板サイズによっては，無鉛半田を使用していてもレッドフリーマークがプリントされていないものがあります）：レッドフリーマーク無鉛半田は，下記の点に注意して使用してください。...
Page 6 Ver. 1.2 2008.06 ENGLISH JAPANESE ENGLISH JAPANESE 1-4. SAFETY CHECK-OUT サービス，点検時には次のことにご注意ください。注意事項をお守りください。サービスのとき特に注意を要する個所については，キャビネット，シャーシ，部品などにラベルや捺印で注意事項を表示しています。これらの注意書き及び取扱説明書等の注意事項を必ずお守りください。指定部品のご使用をセットの部品は難燃性や耐電圧など安全上の特性を持ったものとなっています。従って交換部品は，使用されていたものと同じ特性の部品を使用してください。特に回路図，部品表に0印で指定されている安全上重要な部品は必ず指定のものをご使用ください。部品の取付けや配線の引きまわしはもとどおりに安全上，チューブやテープなどの絶縁材料を使用したり，プリント基板から浮かして取付けた部品があります。また内部配線は引きまわしやクランパによって発熱部品や高圧部品に接近しないよう配慮されていますので，これらは必ずもとどおりにしてください。サービス後は安全点検をサービスのために取外したネジ，部品，配線がもとどおりになっているか，またサービスした個所の周辺を劣化させてしまったところがないかなどを点検し，安全性が確保されていることを確認してください。チップ部品交換時の注意・取り外した部品は再使用しないでください。・タンタルコンデンサのマイナス側は熱に弱いため交換時は注意してください。フレキシブルプリント基板の取扱いについて・こて先温度を270℃前後にして行なってください。・同一パターンに何度もコテ先を当てないでください。（3回以内）・パターンに力が加わらないよう注意してください。注意電池の交換は，正しく行わないと破裂する恐れがあります。電池を交換する場合には必ず同じ型名の電池又は同等品と交換してください。 DSLR-A300_L2...
Page 7 Ver. 1.2 2008.06 ENGLISH JAPANESE ENGLISH JAPANESE 1-5. SIスクリーン，焦点板の交換方法 3 焦点板とVBスペーサを外す。 1 A部を下に押してつめ2箇所を外し，矢印方向にVM FSリテーナを外す。 VBスペーサつめつめ焦点板 VM FSリテーナ 2 VM FSリテーナを外す。 VM FSリテーナ 4 SIスクリーンを外す。 SIスクリーンつめ注意： SIスクリーン交換時は， SIスクリーンに埃や傷を付けないように注意してください。 DSLR-A300_L2 1-5E...
Page 8: Note For Repair
2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some •...
Page 9 2-1. IDENTIFYING PARTS - DISASSEMBLY FLOW - 2-2-1. OVERALL SECTION 2-2-2. FRONT COVER SECTION ⋅ Front Cover ⋅ Control Switch Block (FS62700) ⋅ Side Cover ⋅ Grip Cover Rear Cover ⋅ Rear Cover ⋅ LF-057 Flexible Board AM-013 Board ⋅ MM-078 Flexible Board 2-2-4.
Page 10: Rear Cover
HELP HELP 2-2. DISASSEMBLY EXPLODED VIEW HARDWARE LIST 2-2-1. OVERALL SECTION Follow the disassembly in the numerical order given. 1 Side Cover (1-1 to 1-3) 2 Rear Cover (2-1 to 2-10) 3 Front Cover (3-1 to 3-6) Note: High-voltage cautions Discharging the Capacitor Short-circuit between two points with the short jig about 10 seconds.
Page 11 2-2-2. FRONT COVER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Control Switch Block (FS62700) (1-1 to 1-2) 2 Grip Cover (2-1 to 2-2) 1 Control Switch Block 1-2 (#75) (FS62700) HELP 2 (#75) (#75) 2Grip Cover DSLR-A300_L2...
Page 12 2-2-3. REAR COVER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 LCD (1-1 to 1-14) 2 Control Switch Block (RS62700) (2-1 to 2-8) 1-11 (#118) 1-10 (Claw) (Claw) 1LCD (#118) 1-14 HELP 4 HELP 3 (Claw) (Claw) 1-12...
Page 13 2-2-4. MAIN BOARD SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 AM-013 Board (1-1 to 1-20) 2 MM-076 Board (2-1 to 2-3) 1 AM-013 Board 1-18 (#75) 2MM-076 Board 2-2 (#75) 1-19 Shutter Unit Section - 0 1 (#109) (See Page 2-7)
Page 14 2-2-5. SHUTTER UNIT SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Tebure Unit (1-1 to 1-12) 2 Shutter Unit (2-1) 1 Tebure Unit Do not hang flexible board of mirror box when you remove Tebure Unit. Refer to page 2-16 "2-3.
Page 15 2-2-6. BOTTOM FRAME SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Top Cover (1-1 to 1-7) 2 Bottom Frame (2-1 to 2-4) 3 Battery Holder (3-1 to 3-6) Note: On installation of the top cover, adjust the position of the V lever and the LIVE VIEW/OVF select lever.
Page 16 2-2-7. TOP COVER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Control Switch Block (TK62700) (1-1 to 1-13) 1-13 (#75) (#114) 1-7 (Solder) 1-6 (#14) HELP 25 (#75) 1 Control Switch Block (TK62700) 1-12 (#75) 1-2 (#75) HELP 12...
Page 17: Flash Unit
2-2-8. FLASH UNIT SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Flash Unit (1-1 to 1-6) 2 Stroboscope Base (2-1) 3 Mode Dial (3-1) 1-2 (Claw) 1 Flash Unit HELP 13 2Stroboscope Base (#109) 3 Mode Dial HELP 15 1-1 (#23)
Page 18 2-2-9. BATTERY HOLDER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Media Lid (1-1 to 1-4) 2 ST-196 Board (2-1 to 2-3) 3 Battery Terminal Board (3-1 to 3-15) 3-5 (#109) 1-3 (#108) 3-11 3-10 (#75) (Claw) 3-3 (#109)
Page 19 2-2-10. TERMINAL HOLDER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Eye Piece Frame (1-1 to 1-5) 2 Terminal Holder (2-1) 3 AF Module (3-1 to 3-5) 1 Eye Piece Frame 1-2 (#14) (#23) Mirror Box Section (Penta Unit) (See Page 2-13)
Page 20 2-2-11. MIRROR BOX SECTION (PENTA UNIT) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Penta Unit (1-1 to 1-3) 1 Penta Unit Refer to page 1-2 "1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUS PLATE" when SI screen or focus plate are exchanged. Refer to page 2-24 "2-12.
Page 21 2-2-12. MIRROR BOX SECTION (SUB UNIT-1) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Iris Ring (1-1 to 1-9) 2 Aperture Unit (2-1 to 2-5) 3 AF Driving Unit (3-1 to 3-10) 2 Aperture Unit Refer to page 2-18 "2-6.
Page 22 2-2-13. MIRROR BOX SECTION (SUB UNIT-2) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Charge Base Plate A Unit (1-1 to 1-11) 2 Shutter Charge Lever (2-1 to 2-12) 2-12 Refer to page 2-20 "2-9. LEVERS AND GEARS INSTALLATION"...
Page 23 2-3. IMAGER INCLINATION ADJUSTMENT Checking Method Use the copy stand or place a mirror on the wall, and adjust the accuracy so that the camera is opposed to the mirror. Use the AE master lens as an inspection lens. Obtain the inclination angle with the Photoshop, and perform as follows according to the angle: •...
Page 24 2-4. SHUTTER INSTALLATION Follow the assembly in the numerical order given. 1 Raise Main Mirror up. Mirror Charge Lever Up 2 Rotate Idle Gear Don't damage Idle Gear. Shutter Charge Lever Down Boss 3 Shutter 4 Shutter Flexible Board DSLR-A300_L2 2-17...
Page 25 2-5. IRIS RING REMOVAL/INSTALLATION Removal Rotate the iris ring clockwise, and remove it at the stop position (iris-in end). At this time, do not rotate the iris joint gear of the Aperture Unit. Installation With the Aperture Unit set in the charge position (see "2-7. Aperture Unit Charge Position Setting" ), install it on the front frame set.
Page 26 2-8. APERTURE UNIT FREE POSITION SETTING Set the Aperture Unit to a free position once, if the gear was rotated accidentally and the charge position is disordered, or if the charge position was shifted during disassembly. In a free state, the edge of this spring In a free state, a hole in the gear almost will move up and down about 1 mm if coincides with a hole in the Aperture Unit.
Page 27 2-9. LEVERS AND GEARS INSTALLATION Follow the assembly in the numerical order given. 2-9-1. MIRROR CHARGE/SHUTTER CHARGE LEVERS INSTALLATION - Levers Position - 1 Mirror Charge Lever Assy Mirror Charge Lever Assy 4 Screw (#93) 3 Charge Base Plate C Assy Main Mirror Holder Boss 2 Shutter Charge...
Page 28 2-9-3. CHARGE BASE PLATE B INSTALLATION 1 Charge Base Plate B Assy 2 Screw (#93) Hole Hole 2-9-4. MIRROR DRIVING (SP) INSTALLATION 3 Screw (#93) - Spring Position - 2 Mirror Driving (SP) Retainer Mirror Charge Cam Gear 1 Mirror Driving (SP) Mirror Driving (SP) DSLR-A300_L2...
Page 29 2-10.GREASE APPLICATION AREA Grease uses G-85 (J-6082-626-A). Ring (SP) Ring Roller (C) Shaft Grease Grease Shutter Cam Gear Assy Mirror Charge Cam Gear Grease Grease Front Frame Assy Grease Grease Grease Grease Grease DSLR-A300_L2 2-22...
Page 30 2-11.CLEANING PROCEDURE OF OLPF <Preparation> Make it to Cleaning Mode of Power On/Set Up Menu by using the AC power supply. (It comes to Mirror Up/Shutter Open) Note: Use the AC power supply absolutely. <Cleaning Method> Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
Page 31 2-12.CLEANING PROCEDURE OF VIEWFINDER Note: Confirm it is the same before the following item cleans it after cleaning the viewfinder. 1. Digital zoom check 2. Inclination of Live view image 3. Resolution of Live view image in surrounding 1 Remove the connection of eight flexible board. 3 Remove the diopter adjust cam cover and the diopter adjust click plate after removing one screw.
Page 32 4 Remove the beam splitter block after removing 5 Clean dust with the blower. two screws. Note: Removed parts are not supplied. Blower Please recycle. Screw Beam Splitter Block Caution: Never touch two screws. Don't touch DSLR-A300_L2 2-25E...
Page 33 HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. HELP 1: HELP 3: Switch Block Control Unit (FS62700) Flexible Cover Spring Flexible Cover Spring Claw Switch Block Control Unit (FS62700) HELP 2: HELP 4: Switch Block Control Unit (FS62700) FPC Slider Sheet/FPC Slider Sheet B Switch Block Control Unit (FS62700) Claw...
Page 34 HELP 5: HELP 8: EM RS FPC Shield Sheet/ IS Flexible Unit Fuse Change Caution Label/ Flexible Hole Blind Sheet/ Adhesive Tape EM Shield Insulating Sheet EM RS FPC Shield Sheet Claw EM Shield Insulating Sheet IS Flexible Unit Flexible Hole Blind Sheet Fuse Change Caution Label HELP 6: HELP 9:...
Page 35 HELP 11: DC Jack Harness HELP 12: Flash Unit Harness/Tape (W) Tape (W) Tape (W) Flash Unit Harness DSLR-A300_L2 HELP...
Page 36 HELP 13: HELP 16: Flush Unit GY-008 Flexible Board GY-008 Flexible Board Boss HELP 14: HELP 17: CV Self LED Electrostatic S MA-450 Flexible Board MA-450 Flexible Board CV Self LED Electrostatic S GY-008 Flexible Board HELP 15: HELP 18: CT Mode Dial Assy RM-096 Flexible Board CT Mode...
Page 37 HELP 19: HELP 22: DC Jack Harness Aperture Unit Flexible Borad Iris FPC Protection Sheet Aperture Unit Flexible Borad AF Driving Unit Flexible Borad Iris FPC Protection Sheet HELP 23: Coupler Lever Tension SP Coupler Lever Tension SP HELP 20: BD Side Cover (L) Sheet BD Side Cover Coupler Joint Lever...
Page 38 3. BLOCK DIAGRAMS Link Link OVERALL BLOCK DIAGRAM (1/5) POWER BLOCK DIAGRAM (1/5) OVERALL BLOCK DIAGRAM (2/5) POWER BLOCK DIAGRAM (2/5) OVERALL BLOCK DIAGRAM (3/5) POWER BLOCK DIAGRAM (3/5) OVERALL BLOCK DIAGRAM (4/5) POWER BLOCK DIAGRAM (4/5) OVERALL BLOCK DIAGRAM (5/5) POWER BLOCK DIAGRAM (5/5) DSLR-A300_L2...
Page 39 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VTN-001 FLEXIBLE BOARD AM-013 BOARD (1/5) LF-057 FLEXIBLE BOARD CN3529 CN9451 CN2901 VOUT IC5402 VTN_CCD_OUT...
Page 40 3-2. OVERALL BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (2/5) XSHUTTER_X_SW XSHUTTER_X_SW Q3404 SH_2C 2ND_CURTAIN_MG SHUTTER SH_1C 1ST_CURTAIN_MG DRIVE OVERALL (1/5) (PAGE 3-1) XCF_IN_CA IMG_TEMP1 1ST_CURTAIN_MG...
Page 41 3-3. OVERALL BLOCK DIAGRAM (3/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AF-111 FLEXIBLE AM-013 BOARD (3/5) BOARD CN3511 VOUT AFCCD_VOUT MA-450 AE-032 FLEXIBLE EYE-006 FLEXIBLE BOARD FLEXIBLE AFCCD_CLOCK BOARD...
Page 42 3-4. OVERALL BLOCK DIAGRAM (4/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (4/5) RM-096 FLEXIBLE BOARD Q3511 CN3526 BZ901 BZ_DG BZ_DG BUZZER BUZZER (BUZZER) DRIVE S1_REMOTE J901 S2_REMOTE...
Page 43 3-5. OVERALL BLOCK DIAGRAM (5/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (5/5) MA-450 FLEXIBLE BOARD CN3517 (2/2) (2/2) OVERALL (4/5) (PAGE 3-4) XCS_VG XCS_VG XCS_VG XCS_HPY2 XCS_HPY2...
Page 44 3-6. POWER BLOCK DIAGRAM (1/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (1/5) BT902 BATTERY TERMINAL Q0502, Q0503, CN0503 F0501 Q0505 UNREG_LVDD0 BATT_UNREG B+ SWITCH POWER (2/5) (PAGE 3-7) BATT_SIG...
Page 45 3-7. POWER BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (2/5) IFL-003 FLEXIBLE BOARD BL901 CN3524 IC_3001_6.0V IC_3001_6.0V IC_3001_6.0V BL_A BL_A FINDER BACKLIGHT RM-096 FLEXIBLE CH3_3.3V (IC_3001_3.3V) CH3_3.3V (IC_3001_3.3V)
Page 46 3-8. POWER BLOCK DIAGRAM (3/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (3/5) IC_3001_2.5V IC_3001_2.5V VREF_CAM VREF_CAM EVER_1.5V EVER_1.5V POWER (1/5) EVER_3.3V EVER_3.3V (PAGE 3-6) IC3001 IC3713 MAIN CPU...
Page 47 3-9. POWER BLOCK DIAGRAM (4/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (4/5) AF-111 FLEXIBLE BOARD CN3511 CH3_3.3V (IC_3001_3.3V) CH3_3.3V (AFCCD_3.3V) VCC1 AS_5.0V AS_5.0V IC7801 EVER_3.3V EVER_3.3V AF CCD...
Page 48 3-10. POWER BLOCK DIAGRAM (5/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (5/5) IC2801 VIDEO AMP (18/19) IMG_3.3V IMG_3.3V IC2501 EVER_3.3V EVER_3.3V CF DETECT MM-078 MM-076 BOARD (17/19) D2501...
Page 49 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM BL CONTACT HOLDER UNIT GY-008 FLEXIBLE BOARD LENS CONTACTS CN6501 VTN PENTA BLOCK ASSY BL-016 LED-001 FLEXIBLE BOARD LED901 FLEXIBLE TOKO LED LCD902 BOARD IFL-003 FINDER FLEXIBLE MA-450 FLEXIBLE BOARD BOARD BL901 FLASH UNIT...
Page 50 4-2. SCHEMATIC DIAGRAMS Link Link IS-026 BOARD (1/3) (CCD IMAGER) RM-096 FLEXIBLE BOARD (REMOTE JACK) BL-016 FLEXIBLE BOARD IS-026 BOARD (2/3) (LENS CONTACTS) (AFE, TIMING GENERATOR) IS-026 BOARD (3/3) MA-450 FLEXIBLE BOARD (CONNECTOR) (AFE, TIMING GENERATOR) VTN-001 FLEXIBLE BOARD IFL-003 FLEXIBLE BOARD (FINDER) (LIVE VIEW CCD) LED-001 FLEXIBLE BOARD LF-057 FLEXIBLE BOARD (LCD)
Page 51 Ver. 1.2 2008.06 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS (ENGLISH) (JAPANESE) THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS 回路図共通ノート (In addition to this, the necessary note is printed in （他に必要なノートは各ブロックに記載してあります）【回路図ノート】 each block) ・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの (For schematic diagrams) はその耐圧を省略。単位はすべてμF（pはpF）。...
Page 52 15.1 R4315 R4317 IC4304 100k 220k CXA3691EN-T9 1/16W 1/16W ± 5% BUFFER ± 5% C4311 0.1u CCDOUT_RB-BUFF IDRV C4320 0.001u C4322 0.1u VOUT_RB Q4302 VSUB_CONT R4328 R4327 X4301 FB4331 25MHz 15.1 CCD_H15 3 OUT R4316 R4318 CONT 2 VSS 100k 220k IC4305 D4301...
Page 53 GNDL GNDL C4224 GNDL V3F_C 0.1u VDDH2 VDDH1 R4235 GNDL V4F_F IC4204 H2F_RB CXA3759ER-T2 L4203 FB4203 V3F_F 10uH H-DRIVER C4232 GNDH1 HVDD_RB 220p V3F_B GNDH2 R4232 GNDH1 C4205 C4204 V4F_C VDDH2 4.7u 0.1u H1F_RB 6.3V DRVDD_RB FB4201 VDDH1 C4233 GNDH2 150p GNDL GNDL...
Page 54 GNDL GNDL C4124 GNDL VDDH2 0.1u V1F_E R4135 VDDH1 GNDL V2F_A IC4104 H2F_G L4103 FB4103 V1F_B CXA3759ER-T2 C4132 10uH GNDH2 GNDH1 HVDD_G 220p H-DRIVER V1F_F R4132 VDDH2 GNDH1 C4105 C4104 V2F_E 4.7u 0.1u H1F_G 6.3V FB4101 DRVDD_G VDDH1 C4133 GNDH2 150p GNDL GNDL...
Page 55 VTN_H2 VTN_H1 VTN_RG VTN_CCD_VH LN5423 pin23 LN5422 VTN_CCD_VL LN5421 VTN_CCD_SUB LN5420 LN5419 R5401 C5401 R5402 C5402 0.01u VTN_V4 LN5418 220k 0.01u VTN_V3 LN5417 100k VTN_CCD_VL VTN_V2 LN5416 VTN_V1 LN5415 VOUT C5405 LN5414 AM-013 C5404 VTN_TEMP LN5413 0.1u (1/19) IC5401 LN5412 CN2901 ICX630AQZ-13 Page 4-7...
Page 56 Schematic diagrams of the AM-013 board is not shown. Pages from 4-7 to 4-25 are not shown. DSLR-A300_L2...
Page 57 CN9451 45P VCOM DGND pin23 LN9473 DGND NC(AUO)DGND(SONY) pin22 LN9472 LN9471 LN9470 LN9469 HSYNC LN9468 HSYNC HSYNC VSYNC LN9467 VSYNC VSYNC LN9466 DCLK DCLK DCLK LN9465 LN9464 AM-013 LN9463 (19/19) LN9462 CN3529 Page 4-25 LN9461 of Level 3 LN9460 LN9459...
Page 58 C5201 R5201 C5205 CN5202 CF_3.3V CN5201 XCF_CD1 REG_GND RB5201 CF_D[06] CF_D[03] CF_D06 CF_D[11] CF_D[04] REG_GND CF_D[12] CF_D[04] CF_D04 CF_D[10] RB5202 CF_D10 CF_D[02] CF_D[05] CF_D02 CF_D[13] CF_D[14] CF_D[06] CF_D14 CF_D[14] CF_D[00] CF_D00 CF_D[11] RB5203 CF_D11 CF_D[07] XCF_CE1 CF_D[15] XCF_CE1 CF_D[09] CF_D09 XCF_OE R5212 XCF_CE1...
Page 59 pin1 LN7801 pin2 LN7802 MOD4 VOUT LN7803 VOUT VOUT LN7804 VCC1 LN7805 VCC1 VREF LN7806 IC7801 T8D87Q(Z) LN7807 AF CCD LN7808 LN7809 LN7810 LN7811 MOD1 LN7812 MOD2 LN7813 pin13 pin14 LN7814 MOD3 AM-013 (19/19) CN3511 Page 4-25 of Level 3 Note: IC7801 is not supplied, but this is included in ALX-6270 (AF module).
Page 60 GYVCC SE6202 YAW SENSOR REG_GND C6203 C6204 pin22 LN6222 GOUT_P pin21 LN6221 GOUT_P LN6220 REG_GND VREF_P LN6219 VREF_P LN6218 REG_GND GOUT_Y GOUT_Y LN6217 REG_GND LN6216 VREF_Y VREF_Y LN6215 LN6214 REG_GND AM-013 GYVCC LN6213 GYVCC (19/19) CN3520 LN6212 REG_GND Page 4-25 LN6211 INT_FLASH_FULL of Level 3...
Page 61 BR_Y2 ACT901 pin1 LND001 BR_Y2 BR_Y2 LND034 ACTUATOR BR_Y1 pin2 LND002 BR_Y1 BR_Y1 LND033 (YAW) BR_P2 ACT-001 LND003 BR_P2 BR_P2 LND032 FLEXIBLE BR_P1 LND004 LND031 BR_P1 BR_P1 LND001-LND002 VBRA5 Page 4-30 LND005 VBRA5a of Level 2 POUT1P LND006 Pout1p POUT2N LND007 Pout2n POUT2P...
Page 62 M903 (APERTURE MOTOR) pin18 LND018 pin10 LND010 LND017 LND012 pin9 LND009 LND016 LND011 LND008 LND015 AP-031 FLEXIBLE LND007 LND014 IRIS_PI_E_2 LND001-LND010 LND006 LND013 IRIS_PI_E_2 Page 4-31 IRIS_PI_E_2 IRIS_PI_K of Level 2 LND005 LND012 IRIS_PI_K IRIS_PI_E_2 IRIS_PI_K IRIS_PI_E_1 LND004 IRIS_PI_K LND011 IRIS_PI_E_1 IRIS_PI_E_1 IRIS_PI_A...
Page 63 Note: BZ901 and J901 are not included in RM-096 flexible complete board. Note: SLLK base plate unit is not included C8601 in SLK-003 flexible complete board. 0.001u LF8601 J901 S1_REMOTE REMOTE pin1 LN8601 S1_REMOTE LN8611 CL5801 XIRIS_OPEN_SENSE LN8602 C8602 0.001u CL5802 LN8612 XIRIS_OPEN_GND...
Page 64 AM-013(19/19) CN3530 Page 4-25 LVDD1 pin1 LN5901 of Level 3 pin2 LN5902 LENS_SI CN5904 LENS_SCK LN5903 pin1 LN5981 PGND PGND LN5904 XCS_LENS pin2 LN5982 PGND PGND LN5905 REG_GND LN5983 PGND PGND LN5906 LENS_SO PGND EVER_3.3V LN5984 PGND LN5907 LVDD0 EVER_4.5V LN5985 LVDD0 LN5908...
Page 65 FOCUS_POS_LED_K9 pin1 LN8501 FOCUS_POS_LED_K9 FOCUS_POS_LED_K9 LN8511 FOCUS_POS_LED_K6 pin2 LN8502 FOCUS_POS_LED_K6 FOCUS_POS_LED_K6 LN8512 FOCUS_POS_LED_K5 LN8503 FOCUS_POS_LED_K5 FOCUS_POS_LED_K5 LN8513 FOCUS_POS_LED_K4 COM0 LN8504 FOCUS_POS_LED_K4 FOCUS_POS_LED_K4 LN8514 pin1 LN7401 COM0 COM0 LN7455 FOCUS_POS_LED_K8 SEG21 LED901 pin2 SEG21 LN8505 FOCUS_POS_LED_K8 FOCUS_POS_LED_K8 LN8515 LN7402 SEG21 LN7430 TOKO FOCUS_POS_LED_K7 SEG20...
Page 66 C6356 R6351 C6353 C6352 100k 4.7u 6.3V 6.3V Q6351 2SA1577-T106-R EVER_3.3V LED DRIVE R6359 pin18 LN6368 EVER_4.5V pin17 LN6367 XCS_LM LN6366 CS_LM EYE_SENSE_CTRL LN6365 GRP_ON EYE_SENSE_LED LN6364 IC_3001_SCK CN6351 LN6363 LMCK LM_MODE1 LN6362 RWLM REG_GND LM_MODE2 LN6361 MODE EYE_SPC_K EYE-006 IC_3001_SO FLEXIBLE LN6360...
Page 67 • Refer to page 4-2 for mark 0. FLASH UNIT (FL62700) is replaced as block, so that there PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted. CL6502 D6502 T6501 D6501 RR264M-400 FV02R80TP CN6503 XE_K IGBT_C FLASH UNIT (FL62700) CN6504 R6501 CL6503 EVER_3.3V LD6503...
Page 68 pin51 LN7251 DGND DGND LN7351 pin51 LN7250 DGND DGND LN7350 pin50 pin50 LN7249 LN7349 LN7248 DGND DGND LN7348 LN7247 AV16 AV16 LN7347 LN7246 DGND DGND LN7346 LN7245 LN7345 LN7244 LN7344 LN7243 LN7343 LN7242 DGND DGND LN7342 LN7241 LN7341 LN7240 DGND DGND LN7340 LN7239...
Page 69 1pin LN6701 LN6752 51pin REG_GND REG_GND LN6702 LN6753 CF_A09 CF_A09 LN6754 LN6703 XCF_CD1 XCF_CD1 LN6704 LN6755 CF_A10 CF_A10 LN6705 LN6756 XCF_CD2 XCF_CD2 LN6706 LN6757 CF_A06 CF_A06 LN6707 LN6758 XCF_IOWR XCF_IOWR LN6708 LN6759 CF_A04 CF_A04 LN6760 LN6709 XCF_REG XCF_REG LN6710 LN6761 CF_A01 CF_A01 LN6711...
Page 70 S9106 (MODE DIAL) Note: CN901 is not included in D9105 CONTROL SWITCH BLOCK (TK62700). SML-210LT-T86 (SELF-TIMER) R8201 Q8201 2SC4505T100 BUFFER R8202 IN0_M pin1 LN9101 IN0_M FB8201 LN8207 IN1_M pin2 LN9102 IN1_M FB8202 CN901 LN8208 IN3_M ACCESSORY LN9103 IN3_M FB8203 LN8209 SEL4 SHOE LN9104...
Page 71 S9501 POWER POWER_SW pin1 LN9501 XPOWER_SW DGND pin2 LN9502 DGND (ENTER) / XKEY_MAT_SEL_2 S9503 D9501 LN9504 XKEY_MAT_SEL_2 XKEY_CROSS_COM_1 LN9505 XKEY_CROSS_COM_1 S9502 IN_6 S9502 - S9506 LN9506 XKEY_MAT_IN_6 (CONTROLLER) RB48SKTK XKEY_FUNC_COM LN9507 XKEY_FUNC_COM S9505 XKEY_CROSS_C D9502 LN9508 XKEY_CROSS_C XKEY_CROSS_U LN9509 XKEY_CROSS_U S9202 S9504 XKEY_CROSS_D...
Page 72 4-3. PRINTED WIRING BOARDS Link Link IS-026 BOARD AP-031 FLEXIBLE BOARD SLK-003 FLEXIBLE BOARD VTN-001 FLEXIBLE BOARD RM-096 FLEXIBLE BOARD LF-057 FLEXIBLE BOARD MM-076 BOARD MA-450 FLEXIBLE BOARD GY-008 FLEXIBLE BOARD AE-032 FLEXIBLE BOARD HOL-004 FLEXIBLE BOARD ST-196 BOARD AFP-003 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS DSLR-A300_L2...
Page 73 Ver. 1.2 2008.06 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS (ENGLISH) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible board Pattern from the side which enables seeing.
Page 74 IS-026 (6 layers) : Uses unleaded solder. IS-026 BOARD HDRV6 HDRV6 C4328 FB4102 C4304 C4317 R4232 FB4202 IC4301 R4135 C4118 C4303 C4225 C4221 C4205 C4125 C4121 C4132 C4331 C4302 IC4204 C4306 C4124 IC4104 IC4302 FB4103 FB4203 L4201 C4119 C4329 C4220 AFE-TG_3 AFE-TG_3 C4219...
Page 75 VTN-001 (2 layers) : Uses unleaded solder. VTN-001 FLEXIBLE BOARD VTN_CCD_VL C5404 1-873-788- 11 VTN_CCD_VH IC5402 R5403 VTN001 VTN001 VTN001 V V T T V V V T 0 0 N N N 0 1 1 0 0 01 1 1 C5405 Note: VTN-001 flexible complete board and all mounted parts are not supplied, but they are included in VTN PENTA block assy.
Page 76 Printed wiring boards of the AM-013 board is not shown. Pages 4-44 and 4-45 are not shown. DSLR-A300_L2...
Page 77 LF-057 (2 layers) : Uses unleaded solder. LF-057 FLEXIBLE BOARD > P I < 1 - 8 7 3 - 8 4 5 - L F - 0 5 7 R9456 R9457 C9461 LN9451 C9465 LN9452 C9456 LN9453 LN9454 LN9455 LN9456 LN9457 C9460...
Page 78 MM-076 (2 layers) : Uses unleaded solder. MM-076 BOARD (SIDE A) MM-076 BOARD (SIDE B) R5231 R5246 R5228 C5204 R5226 CN5202 R5244 R5222 CompactFlash/ R5220 Microdrive R5218 R5216 R5215 R5213 R5212 R5201 CN5203 CF CARD EJECT LEVER CN5201 1-873-778- 11 1-873-778- 11 DSLR-A300_L2 MM-076...
Page 79 GY-008 (1 layer) : Uses unleaded solder. GY-008 FLEXIBLE BOARD LN6222 LN6221 LN6220 LN6219 LN6218 LN6217 LN6216 LN6215 LN6214 LN6213 LN6212 LN6211 LN6210 LN6209 LN6208 LN6207 LN6206 LN6205 LN6204 LN6203 (PITCH) LN6202 1-873-784- GY-008 LN6201 SE6201 (YAW) GYVCC C6203 1-873-784- 11 LN6242 LN6241 LN6240...
Page 80 HOL-004 (2 layers) : Uses unleaded solder. HOL-004 FLEXIBLE BOARD Note: HOL-004 flexible complete board and all mounted parts are not supplied, but they are included in slider unit. RB7502 IC7501 RB7501 LND031 LND032 LND033 LND034 1-872-900- 11 DSLR-A300_L2 HOL-004 4-49...
Page 81 AFP-003 (1 layer), AP-031 (1 layer) : Uses unleaded solder. AFP-003 FLEXIBLE BOARD AP-031 FLEXIBLE BOARD Note: AFP-003 flexible complete board and all mounted parts are not supplied, Note: AP-031 flexible complete board and all mounted parts are not supplied, but they are included in AF driving unit.
Page 82 SLK-003 (1 layer), RM-096 (1 layer) : Uses unleaded solder. SLK-003 FLEXIBLE BOARD Note: SLK-003 flexible complete board and all mounted parts are not supplied, but they are included in charge base plate B assy. -003 AAAAA >PI< D5801 LN5801 LN5802 LN5803 LN5804...
Page 83 MA-450 (1 layer) : Uses unleaded solder. MA-450 FLEXIBLE BOARD MA-450 >PI< 1-873-783- LN5974 LN5973 LN5972 LN5965 LN5964 LN5963 LN5975 LN5970 LN5971 LN5966 LN5967 LN5962 LN5976 LN5969 LN5968 LN5961 LN5977 1-873-783- 11 D5906 DSLR-A300_L2 MA-450 4-52...
Page 84 AE-032 (2 layers) : Uses unleaded solder. AE-032 FLEXIBLE BOARD C6351 C6353 LN6351 LN6352 >PI< LN6353 LN6354 LN6355 LN6356 LN6357 LN6358 LN6359 LN6360 LN6361 LN6362 LN6363 LN6364 LN6365 LN6366 LN6367 AE-032 AE 032 AE 032 AE 032 AE 032 AE 032 AE 032 AE 032 AE 032...
Page 85 ST-196 (2 layers) : Uses unleaded solder. ST-196 BOARD (SIDE B) ST-196 BOARD (SIDE A) CN6501 CL6501 C6501 T6501 CL6502 C901 C6502 CHARGING CAPACITOR LD6502 LD6501 CL6503 R6513 CL6504 C6504 D6502 LD6503 (For Discharge) EVER_3.3V R6515 R6510 R6502 C6507 R6516 C6503 R6514 CL6506...
Page 86 NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS EXPLODED VIEWS Link Link OVERALL SECTION FRONT COVER SECTION REAR COVER SECTION MAIN BOARD SECTION BOTTOM FRAME SHUTTER UNIT SECTION...
Page 87 Ver. 1.2 2008.06 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST (ENGLISH) NOTE: When indicating parts by reference number, • -XX, -X mean standardized parts, so they may have some differences from please include the board name. the original one.
Page 88 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1. EXPLODED VIEWS 5-1-1. OVERALL SECTION ns: not supplied Rear Cover Section (See page 5-4) Main Board Section (See page 5-5) Front Cover Section (See page 5-3) Ref. No. Part No.
Page 89 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-2. FRONT COVER SECTION ns: not supplied Ref. No. Part No. Description Ref. No. Part No. Description 3-288-191-01 CV GRIP COVER (629) 3-282-783-01 CT FOCUS SELECTION KNOB X-2189-658-1 CV FRONT COVER ASSY 628 * 57 3-282-784-01 CT FC CLICK PLATE 3-282-781-02 CT LENS LOCK BUTTON...
Page 90 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-3. REAR COVER SECTION ns: not supplied #118 CAUTION: For the part of 110, cut SHEET, ADHESIVE (2-649- 300-01) into the desired length and use it.
Page 91 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-4. MAIN BOARD SECTION ns: not supplied - 0 1 Shutter Unit Section (See page 5-6) #109 BH3001 (Note)
Page 92 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-5. SHUTTER UNIT SECTION ns: not supplied #110 Tebure Unit Section (8mm x 8mm) (See page 5-7) Bottom Frame Section (See page 5-8) CAUTION:...
Page 93 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. HARDWARE LIST 5-1-6. TEBURE UNIT SECTION (including IC4303 (CCD imager) and IS-026 complete board) (Note 1, 2) #111 (including IS-027 flexible board) (including ACT901, ACT902, ACT-001 flexible board (Note 3)
Page 94 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-7. BOTTOM FRAME SECTION Top Cover Section (See page 5-9) #112 (15mm x 9mm) #113 Battery Holder Section (See page 5-11) #110 Terminal Holder Section...
Page 95 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-8. TOP COVER SECTION #114 #115 PL901 (15mm x 9mm) Flash Unit Section (See page 5-10) CAUTION: CN901 For the part of 353, cut WOVEN (T0.25), FABRIC NON...
Page 96 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-9. FLASH UNIT SECTION ns: not supplied #109 White (Note) Note: About the arrangement of harness, Black (Note) Pink (Note) refer to HELP 10.
Page 97 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-10. BATTERY HOLDER SECTION ns: not supplied #109 #108 #109 #116 BT902 C901 • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description A-1437-493-A ST-196 BOARD, COMPLETE * 463...
Page 98 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-11. TERMINAL HOLDER SECTION ns: not supplied Mirror Box Section (Penta Unit) (See page 5-13) (including SE901 and EYE-006 flexible board) (8mm x 8mm) BZ901 J901...
Page 99 Ver. 1.2 2008.06 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.1 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-12. MIRROR BOX SECTION (PENTA UNIT) ns: not supplied (including BL901, LCD902, LED901, AE-032 flexible board, IFL-003 flexible board, LED-001 flexible board and #117 #117...
Page 100 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-13. MIRROR BOX SECTION (SUB UNIT-1) (including M903 (aperture motor) and AP-031 flexible board) Mirror Box Section (Sub Unit-2) (See page 5-15) 705 706 (including M901 (AF motor), EN-022 board, AFM-002 flexible board and AFP-003 flexible board) Ref.
Page 101 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-14. MIRROR BOX SECTION (SUB UNIT-2) ns: not supplied (including BL-016 flexible board) (including SLK-003 flexible board) (including M902 (charge motor)) Ref. No. Part No. Description Ref. No. Part No. Description 3-268-935-01 SP, SUB MIRROR FUNCTION 3-268-937-01 RETAINER, ADJUSTMENT PLATE...
Page 102 Electrical parts list of the AM-013 board is not shown. Pages 5-16 to 5-22 are not shown. DSLR-A300_L2...
Page 103 Ver. 1.2 2008.06 GY-008 IS-026 LF-057 MA-450 The changed portions from Ver. 1.1 are shown in blue. MM-076 RM-096 ST-196 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-1437-492-A GY-008 FLEXIBLE BOARD, COMPLETE A-1437-495-A MM-076 BOARD, COMPLETE ******************************* ************************ <...
Page 104 ST-196 Ref. No. Part No. Description Ref. No. Part No. Description * CN6504 1-821-666-21 PIN, CONNECTOR < DIODE > 0* D6501 6-502-219-01 DIODE FV02R80TP 0 D6502 6-501-119-01 DIODE RR264M-400 < IC > 0* IC6501 6-711-948-01 IC BD4216NUV-E2 < TRANSISTOR > 0* Q6501 6-551-937-01 TRANSISTOR TIG032TS-S-TL-E <...
Page 105 Ver. 1.2 2008.06 The changed portions from Ver. 1.1 are shown in blue. Checking supplied accessories. Note: This item is supplied with the unit as an accessory, but is not prepared as a service part. Battery Charger Power Cord Quick Start Guide 0 1-792-549-41 (J) BC-VM10 3-287-968-11 (ENGLISH) (AEP, UK, E)
Page 106 File this supplement with the service manual. (DI08-031) • Addition of Champagne Gold Model Champagne Gold Model was added at DSLR-A300. This supplement covers only differences from models other than Black. Refer to the parts list of original service manual about other parts.
Page 107 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS Page Black Model Champagne Gold Model Ref. No. Part No. Description Ref. No. Part No. Description X-2187-837-1 BD BATTERY CASE LID ASSY X-2318-493-1 BD BATTERY CASE LID ASSY 628N 3-282-749-02 BD SIDE COVER (L) 3-282-749-11 BD SIDE COVER (L) 3-282-750-01 BD DC•REMOTE LID 3-282-750-11 BD DC•REMOTE LID...
Page 108 • Suffix No. of AE-032 flexible board has been changed from 11 into 12 . About suffix No. 11 and 12 , there are no changes of schematic diagram. 2008H0500-1 DSLR-A300_L2 © 2008.8 Sony EMCS Co. 9-852-277-82 Published by Kohda TEC...
Page 112 : Points changed portion. • Change of AE-032 Flexible Board’s Suffix No. 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS AE-032 FLEXIBLE BOARD (Service manual page 4-53) Suffix: -11 Suffix: -12 • Change of Repair Parts 3. BLOCK DIAGRAMS 3-6.
Page 114 : Points changed portion. Page Former 5-12 (8mm x 8mm) (8mm x 8mm) Ref. No. Part No. Description Ref. No. Part No. Description 2-633-540-01 SHEET (C), INSULATING 5-14 2-689-312-02 RING, IRIS 2-689-312-21 RING, IRIS 5-2. ELECTRICAL PARTS LIST Page Former Ref.
Page 115 File this supplement with the service manual. (DI08-269) • Change of Board’s Suffix No. • Suffix No. of AM-013 board has been changed from 13 , 23 into 25 . 2008J0500-1 DSLR-A300_L2 © 2008.10 Sony EMCS Co. 9-852-277-86 Published by Kohda TEC...
Page 119 R5226 XCF_RST R5226 RESET RESET R5246 100k 100k R5246 XCF_WAIT R5228 R5228 XCF_WAIT WAIT WAIT CF_A[02] CF_A[02] CF_A[01] CF_A[01] RB5206 CF_A[00] CF_A[00] INPACK INPACK R5231 XCF_REG R5231 XCF_REG 2009F0500-1 DSLR-A300_L2 © 2009.6 Sony EMCS Co. 9-852-277-88 Published by Kohda TEC...
Page 122 & : Points added portion. : Points deleted portion. • Change of Repair Parts 5. REPAIR PARTS LIST Page Former Ref. No. Part No. Description Ref. No. Part No. Description 0 BH3001 1-756-615-41 HOLDER, BATTERY (Note) 0 BH3001 1-756-615-61 HOLDER, BATTERY (Note) (including IC4303 (CCD imager) (including IC4303 (CCD imager) and IS-026 complete board) (Note 1, 2)
Page 123 HARDWARE LIST (1/7) #1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver)
Page 124 HARDWARE LIST (2/7) #21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver)
Page 125 HARDWARE LIST (3/7) #41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping) (Silver) (Silver) (Red) (Silver) 3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61 #45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5 (Silver) (Red)
Page 126 HARDWARE LIST (4/7) #64: M1.7 X 5.0 (Tapping) #61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 (Silver) (Black) (Silver) (Black) 2-666-551-21 7-682-549-09 3-080-202-21 3-060-811-21 12.5 10.0 #65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0 (Silver) (Silver)
Page 127 HARDWARE LIST (5/7) #81: M1.7 X 2.5 #82: M1.4 X 1.4 #83: M1.7 X 7.0 (Tapping) #84: M2.0 X 3.0 (Silver) (Silver) (Black) (Silver) 2-515-756-01 3-272-251-01 3-080-204-41 3-072-453-11 #85: M1.7 X 2.5 #86: M1.7 X 4.0 (Tapping) #87: M1.6 X 5.3 #88: M1.6 X 5.9 (Tapping) (Black) (Silver)
Page 128 HARDWARE LIST (6/7) #101: M2.0 X 5.0 #102: M2.6 X 8.0 #103: M2.6 X 10.0 #104: M3.0 X 8.0 (Silver) (Black) (Silver) (Black) 7-621-555-39 7-621-284-30 7-685-794-09 7-682-548-09 10.0 #105: M2.0 X 4.0 #106: M2.0 X 6.0 #107: M2.0 X 5.0 #108: M1.7 X 3.0 (Tapping) (Red) (Black)
Page 129 HARDWARE LIST (7/7) #121: M2.0 X 4.0 (Tapping) #122: M3.0 X 6.0 #123: M4.0 X 8.0 #124: M1.7 X 2.0 (Silver) (Black) (Black) (Silver) 7-682-547-09 3-080-205-11 7-682-561-09 2-599-475-01 #125: M1.4 X 3.0 #126: M2.9 X 3.5 #127: M3.0 X 25.0 #128: M4.0 X 12.0 (Black)
Page 130: Revision History
Reverse 985227737.pdf Revision History ∗: S.M. revised only top cover. S.M. Rev. Ver. Date History Contents issued 2008.03 Official Release — — 2008.05 Supplement-1 • Addition of Champagne Gold Model (S1 DI08-031) 2008.06 Revised-1 • Addition of E and Japanese Models (A1 DI08-124) •...

Sony DSLR-A300 Service Manual

Quick Links

Related Manuals for Sony DSLR-A300

Summary of Contents for Sony DSLR-A300

Page 2: Specifications

Page 3: Unleaded Solder

Page 8: Note For Repair

Page 10: Rear Cover

Page 17: Flash Unit

Page 130: Revision History