MarkBass EVO 1 Owner's Manual
  1. Manuals
  2. Brands
  3. MarkBass Manuals
  4. Amplifier
  5. EVO 1
  6. Owner's manual

MarkBass EVO 1 Owner's Manual

Head
Hide thumbs
Table of Contents

Advertisement

Quick Links

v. 14.march.2017
OWNER'S MANUAL

Advertisement

Table of Contents
loading

Related Manuals for MarkBass EVO 1

Summary of Contents for MarkBass EVO 1

  • Page 1 v. 14.march.2017 OWNER’S MANUAL...

  • Page 2: Important Safety Instructions

    MORE INFORMATION For warranty and service information, please contact your local Markbass distributor (contact information available at www.markbass.it). For more technical information, please visit us at www.markbass.it and ll out the form on the Support page. We hope you enjoy your power amp and use it to make great music! “The Lightning Flash with arrowhead symbol...
  • Page 3 MIDI In port, on board tuner, aux in and headphones out, FX loops, XLR Line Outs, and a powerful 500W MPT (Mark Proprietary Technology) power amp. We hope you will enjoy your new rEVOlutionary bass amp, and we invite you to contact us any time with your comments and questions, at info@markbass.it. Thanks again, and good music!

  • Page 4: Front Panel

    (Markbass Little Mark III) for your preference thanks to the MARKBASS EVO SOFTWARE. flagship Markbass amplifier, solid-state preamp with warm and natural sound, - FX ON/OFF switching can be controlled by the EVO pedal. faithfully reproduces the true tone of your instrument - In MIX mode the effects don’t work simultaneously.
  • Page 5 (VOX ® AC 120 ®) 25) ON/OFF SWITCH This switch delivers AC power to the amp. vintage, mellow sound The Markbass EVO 1 is manufactured to be used in the country where it has • JMayor (MARSHALL ® MAJOR ®) been sold, and it’s factory preset to that country’s voltage.

  • Page 6: Rear Panel

    B E A D G C 31) USB This USB port allows to connect your Markbass EVO 1 to a computer thanks to an USB A/B 4 ohm, the speaker outputs are in parallel). (printer) cable to set your preferred AMPs on CH1 and CH2 and parameters of FX1/FX2 INPUT 1 The speaker JACK outs (27-29) accepts ¼”...
  • Page 7 32/34) SEND/ RETURN 1 If you use effect pedals or rack gear, you can route them through the CH1 using SEND 1 (32) and RETURN 1 (34), connecting the SEND to the input of the effect and the RETURN to the effect’s output using instrument cables.

  • Page 8: Midi Functions

    JAPAN 10 A 100V T 5x20 Amps Selection: 6 for CH1 / 6 for CH2 Markbass amps/combos are manufactured to be sold and used in the country of purchase, and they are OTHER CONTROLS (commons) factory preset to at country’s voltage.
  • Page 9 The EVO can be controlled also via programmable MIDI pedalboard as for the MIDI commands listed with your computer. below: - Connect the USB port on the rear panel of the Markbass EVO 1 to a computer using a USB A/B (printer) • TRX MIDI CHANNEL #0 cable, when the unit is communicating with the software the connection LED on the left bottom side will turn from grey into green.
  • Page 10 Product specifications are subject to change without notice Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52 - Tel. +39 085 446 3755 - Fax +39 085 440 7764 - www.markbass.it - info@markbass.it...

Table of Contents