Download Print this page

Sealey PDM100B Instruction Manual page 2

Bench mounted pillar drills

Advertisement

Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
3
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non-stable work piece with a clamp, vice or other adequate holding device.
3
3 Avoid unintentional starting.
DO NOT use the drill for a task it is not designed to perform.
7
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the drill if damaged.
7
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
7
the drill when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
DO NOT exceed the rated capacity of the drill.
7
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
7
DO NOT leave the drill operating unattended.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT pull the cable from the power supply.
7
When not in use switch off the drill, remove plug from the power supply and do not leave until the drill chuck has come to a complete stop.
3
2. DESCRIPTION
These bench mounted variable speed drills are suitable for industrial, agricultural and woodworking applications. The drills are fitted
with flip-up safety guards and "No-Volt Release" switches which prevent accidental restart after a mains power interruption. A rack and
pinion feed shaft with preset depth control for repetitive work is also included. Morse taper spindles accept taper shank bits.
Mortice attachments, work clamps and vices are also available for these drills, contact your local Sealey dealer for information.
Model PDM155B has a built-in lamp to illuminate the drill bit and workpiece.
3. TECHNICAL SPECIFICATIONS
Model
Chuck size (mm)
Spindle Nose Taper
Swing (mm)
Chuck to Upright Face (mm)
Spindle Travel (mm)
Number of Speeds
Speed Range (rpm)
Spindle to Table - max. (mm)
Spindle to Base - max. (mm)
Working Table (mm)
Working Base (mm)
Overall Base (mm)
Column Diameter (mm)
Collar Diameter (mm)
Overall Height (mm)
Voltage (AC)
Motor (W) Nominal/Maximum
Weight
Optional Keyless Chuck
Integral Work Light
4. CONTENT
4.1. Package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your dealer immediately.
3 Head Assembly
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2 - table arm & bracket)
3 Arbor
3 Wedge
© Jack Sealey Limited
PDM100B
PDM125B
16
16
MT2
MT2
314
403
127
165
60
80
12
16
180 - 2740
190 - 3000
420
485
540
700
200 x 200
254 x 254
165 x 155
205 x 200
345 x 210
450 x 270
60
73
55
55
850
1050
230
230
370/550
370/550
35Kg
52Kg
PDM/KC
PDM/KC
NO
NO
3 Base
3 Feed Handle
3 Table
3 Bolts (4)
3 Set Screws (2)
3 Hex. Keys (2)
Original Language Version
PDM155B
16
MT2
460
190
80
16
190 - 3000
475
660
290 x 290
205 x 200
495 x 290
80
60
1050
230
370/550
62Kg
PDM/KC
YES
3 Chuck and Key
3 Table Arm, Bracket and Worm
3 Rack and Rack Ring
3 Safety Guard
PDM100B, PDM125B, PDM155B
Issue: 4 (SP) - 10/12/13

Advertisement

loading

This manual is also suitable for:

Pdm125bPdm155b